Coplax PH1001T Portable Electric Space Heater with Thermostat Instruction Manual

Coplax PH1001T Portable Electric Space Heater with Thermostat

Specifications

• Model: PH1001T
• Power: 120V~ 60Hz 1500W
• For household use only

Read all the instructions carefully before you use the appliance and keep it for future use.

IMPORTANT INSTRUCTIONS

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: READ AND SAVE THESE INSTRUCTIONS

• READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCTS DESCRIBED PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT
• IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
• RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

Preparation before operating

1. Check if the electrical voltage of the main supply and the load of the socket match the rated voltage and power marked on the rating label of the appliance.
2. Check if the socket and the plug are undamaged, and put the plug well in the socket.
3. Put the appliance on a stable and flat surface for no risk of falling.
4. Be sure that there is enough space for the ceramic heater while operating, at least 50 cm around the appliance, and right before the air outlet, the distance should be at least 120 cm.

Safety Precautions

1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front of the heater and keep them away from the sides and rear.
3. Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
4. Always unplug the heater when not in use.
5. Do not operate any heater with a damaged cord or plug or after the heater malfunctions, or has been dropped or damaged in any manner. Discard the heater, or return to the authorized service facility for examination or repair.
6. Do not use outdoors.
7. Do not run the cord under the carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from the traffic area so that it will not be tripped over.
8. To disconnect the heater, turn the controls off, then remove the plug from the outlet.
9. Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
10. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked.
11. A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
12. Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
13. Always plug heaters directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
14. This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate the heater where it may fall into a bathtub or other water container.

WARNING : This product is equipped with a polarized plug (one blade is wider than the other blade). To reduce the risk of electrical shock, this plug will fit into a polarized cutlet only one way. This is a safety feature. If you are unable to insert the plug into the electrical outlet, try reversing the plug. If the plug still does not fit, contact a qualified electrician. Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. Always plug heaters directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap ( outlet/power strip).

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT USE THIS HEATER WITH ANY SOLID-STATE SPEED CONTROL DEVICES. WARNING: DO NOT DEPEND ON THE ON/OFF BUTTON AS THE SOLE MEANS OF DISCONNECTING POWER WHEN SERVICING OF MOVING THE HEATER. ALWAYS UNPLUG THE POWER CORD.

CAUTION: TO PREVENT ELECTRIC SHOCK MATCH THE WIDE BLADE OF THE PLUG TO THE WIDE SLOT, AND FULLY INSERT.

SAVE THESE INSTRUCTIONS

Product Parts

Operation Instructions

1. Turn the thermostat switch to the minimal value, and at the same time turn the heat select switch to the “O” position.
2. Plug in the appliance, and turn the thermostat switch to the maximum position. Then turn the heat select switch to choose air or warm air and the temperature of warm air as below. While working the indicator light will be on.
3. Turn the heat select switch to “position, the heater blows cool air.
4. Turn the heat select switch to the “I” position, and the heater blows warm air, working at Low.
5. Turn the heat select switch to the “II” position, and the heater blows warm air, working at High.
6. Turn the heat select switch to the “O” position, the heater stops working, the indicator light will be off.
7. Adjust the thermostat switch to a suitable position for the desired temperature setting.
8. When you feel the room temperature comfortable, turn the thermostat switch anti-clockwise slowly to the minimal position until the appliance stops working.
9. Then the thermostat switch will keep the room temperature at the desired temperature automatically.
10. Tip over-safety switch is designed to switch the heater off if it is lifted or falls over. If the heater is placed on a very indented surface or a carpet with an exceptionally long, soft pile the safety switch may prevent the heater from turning on. Should this happen replace the heater on a firmer, smoother, surface.

Protective System

1. To avoid risk to human beings or damage to internal components, the ceramic heater has a security system that will automatically switch off the appliance if the heat reaches the safety limit. If overheating occurs:
2. Turn the heat select switch to “O” position, turn the thermostat switch to the minimal position and remove the plug from the socket.
3. Check if the air flows smoothly before the outlet and inlet, and if the appliance is put in the right position. If so, get it in order before restarting the appliance.
4. Let the ceramic heater cool down for at least 10 minutes before you start it again.
5. Plug in the appliance and switch it on. If the appliance can’t operate normally, remove the plug immediately from the socket and have the ceramic heater serviced by an appointed service only.

Maintenance and Cleaning

1. Before you turn off the appliance, turn the heat select switch to the “ “position. After operating for 3 to 5 minutes lower the internal temperature of the appliance, and then turn the heat select switch to “O” position.
2. Clean the air inlet and air outlet of the appliance regularly (at least twice a year normally).
3. Before you clean the appliance, turn off the heater first, then remove the plug from the socket, and wait until the appliance cools down.
4. Use a damp cloth to clean the surface of the appliance, avoid water going inside the appliance, and dry the appliance before use or storage.

WARNING: To avoid the danger of electric shock, unplug from the outlet when not in use and before cleaning. If the supply cord is damaged, it must be replaced by the manufactory or its service agent or a similarly qualified person to avoid a hazard.

• Children of less than 3 years should be kept away unless continuously supervised.
• Children aged from 3 years and less than 8 years shall only switch on/off the appliance provided that it has been placed or installed in its intended normal operating position and they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children aged from 3 years and less than 8 years shall not plug in, regulate and clean the appliance or perform user maintenance.

CAUTION — Some parts of this product can become very hot and cause burns. Particular attention has to be given where children and vulnerable people are present.
Any other servicing should be performed by an authorized service representative.

FAQ

• Q: Can I use this heater with a solid-state speed control device?
  • A: No, using this heater with any solid-state speed control devices is not recommended as it may pose a risk of fire or electric shock.
• Q: How do I disconnect the power when servicing or moving the heater?
  • A: Always unplug the power cord instead of relying solely on the on/off button to disconnect the power.
• Q: What should I do if the heater does not turn on?
  • A: If the heater does not turn on, ensure that it is placed on a firm and smooth surface. If it is placed on an indented surface or a carpet with an exceptionally long, soft pile, the tip-over safety switch may prevent the heater from turning on. In such cases, replace the heater on a firmer and smoother surface.

MODEL: PH1001T 120V~ 60Hz 1500W
FOR HOUSEHOLD USE ONLY

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>