Haier HDW15V2 Dishwasher User Manual

: June 16, 2024
: Haier

Haier HDW15V2 Dishwasher

Product Information

Specifications

Model: HDW15V2/ HDW15V3
Intended Use: Domestic use inside the house
Standards and Directives: Meets all applicable EC directives with corresponding harmonized standards

Product Usage Instructions

Safety

Intended Use: The appliance is designed for domestic use inside the house. It is not intended for commercial or industrial use. Do not use it for purposes other than that for which it was designed, as it may cause hazards and loss of warranty claims.
Standards and Directives: This product meets the requirements of all applicable EC directives with the corresponding harmonized standards, which provide for CE marking.
Before Switching on the Appliance for the First Time: Ensure that there are no foreign objects or packaging materials in, near, or on the appliance.

During Daily Use:

Supervise children to prevent them from playing with the appliance.
Ensure that sharp pointed objects (e.g. knives) are placed in a way that there is no danger of injury.
WARNING: Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed.
Avoid contact with the skin and eyes, and keep children away from the dishwasher when the door is open. Check that the detergent receptacle is empty after completion of the wash cycle.

Product Description

Thermo Dry Top
Spray Upper spray
Arm Lower spray
Arm Filters
Rinse aid dispenser
Detergent dispenser
Rating label
Cutlery basket (Applicable to models HDW15V2)
Lower basket
Upper basket
Knife rack
The third basket (Applicable to models HDW15V3)

Control Panel

HDW15V2W1/S1:

The control panel consists of the following elements:

ON / OFF button
START / PAUSE button
PROGRAMME Touch button
Time & Info Display/Indicator Icon
Option Indication
Status Indication
Time & Info display: Displays the program cycle time, program start delay time, error codes, and service information. It also shows the remaining time in hours of a delayed program start or the remaining program cycle time in hours and minutes.
Please note that the displayed time may vary due to local conditions and daily working load.

Indicator Icon – Rinse aid: If the indicator lights up, it means that the rinse aid is empty. After adding Rinse Aid, press for 3 seconds and the light will go out.

FAQ

Q: What should I do if the dishwasher detergent is swallowed?

A: Dishwasher detergents can be extremely dangerous if swallowed. In case of ingestion, seek medical attention immediately.

Thank you for purchasing a Haier product

Please read these instructions carefully before using this appliance. The instructions contain important information that will help you get the best out of the appliance and ensure safe and proper installation, use and maintenance.
Keep this manual in a convenient place so you can always refer to it for the safe and proper use of the appliance.
If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass on this manual so that the new owner can become familiar with the appliance and safety warnings.

Legend

General information and tips
Warning – Important Safety information
Environmental information

Disposal

Help protect the environment and human health. Put the packaging in applicable containers to recycle it. Help to recycle waste of electrical and electronic appliances.
Do not dispose of appliances marked with this symbol with the household waste.
Return the product to your local recycling facility or contact your municipal office.
WARNING Risk of injury or suffocation!
Disconnect the appliance from the main supply. Cut off the main cable and dispose of it. Remove the door catch to prevent children and pets from getting closed in the appliance.

Safety

Intended Use

The appliance is designed for domestic use inside the house. It is not intended for commercial or industrial use.
Do not use it for purposes other than that for which it was designed. may cause hazards and loss of warranty claims.

Standards and Directives

This product meets the requirements of all applicable EC directives with the corresponding harmonized standards, which provide for CE marking.

Before Switching on the Appliance for the First Time

make sure all packaging is removed and is kept out of children’s reach.
make sure that the electrical information on the rating plate agrees with the power supply. If it does not, contact an electrician.
use a separate earthed socket for the power supply. The appliance must be earthed.
make sure the plug is easily accessible.
make sure only the delivered electric cable and hose set are used.
hold the plug and not the electric cable when unplugging the power supply.
make sure not to damage the electric cable and the plug. If damaged, have it replaced by an electrician.
make sure the hose joints and connections are firm and there is no leakage.

Do not

install or use the appliance where the temperature is below 5 °C.
use multi-plug adapters and extension cables.
let persons, children included, with reduced physical sensory, reduced mental functions or lack of experience and knowledge use the appliance if not supervised by a person responsible for their safety.
put flammable products or items that are wet with flammable products in, near, or on theappliance.

During Daily Use

Do…

supervise children to prevent them from playing with the appliance.
put sharp pointed objects (e.g. knives) in a way that there is no danger of injury.

Do not…

open the door while a program operates. The appliance can release hot steam.
keep the appliance door open without supervision to prevent tripping and falling.
let children or pets come close to the appliance when the door is open.
Lsit or place heavy items on the open door.
remove the dishes from the appliance until the program is completed. There can still be detergent on the dishes.
drink the water in the appliance. The water may be contaminated with detergent residues.
cover any ventilation openings in the base with a carpet or similar object.
use water spray or steam to clean the appliance.
let the children do the cleaning and user maintenance without supervision.

WARNING:

Some dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed.
Avoid contact with the skin and eyes and keep children away from the dishwasher when the door is open.
Check that the detergent receptacle is empty after completion of the wash cycle.

Product Description

Haier-HDW15V2-Dishwasher-fig-4

Thermo Dry Top
spry Upper spray
arm Lower spray
arm Filters
Rinse aid dispenser
Detergent dispenser
Rating label
Cutlery basket”
Lower basket
Upper basket
Knife rack
The third basket”

Accessories

Check the accessories and literature under this list:

Applicable to models HDWI5V2.
Applicable to models HDWI5V3.

Control Panel

HDW15V2W1/S1 :

ON / OFF button
START / PAUSE button
PROGRAMME Touch button
Time & Info Display/Indicator Icon
Option Indication
Status Indication

HDW15V3W1/S1 :

ON / OFF button
Time & Info Display
START / PAUSE button
Option Indication
PROGRAMME Touch button
Status Indication

Time & Info display

During any selection the display shows by flashing related information like
Programme cycle time
Programme start delay time
Error codes and service information

After start of an operation it displays without flashing:

Remaining time in hours of a delayed programme starts, e.g. 24h
Remaining programme cycle time in hours + minutes, e.g. 1:59
While running it may vary due to local conditions and daily working load.

Indicator Icon

Haier-HDW15V2-Dishwasher-fig-10

Status Indicators

Option Indication

Programmes

Haier-HDW15V2-Dishwasher-fig-13

The appliance senses the type of soil and the quantity of items in the baskets. It automatically adjusts the temperature and quantity of water, energy consumption and programme duration.
With this programme you can wash a load with fresh soil. It gives good washing results in a short time.
Use this programme to quickly rinse the dishes. This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance. Do not use detergent with this programme!

On HDW15V3 models

Before first Use

First Steps

Remove all packaging materials, keep them out of children’s reach and dispose them in an environmentally friendly manner. There could be water residue inside the appliance due to quality checks in the factory.

Perform the following steps:

Install the appliance.
- Refer to section INSTALLATION.
Only for use of Multitabs:Adjust the rinse aid setting.
- Refer to section DIFFERENT SETTINGS FOR RINSE AID.
Fill the rinse aid dispenser.
- Refer to section HOW TO FILL THE RINSE AID DISPENSER.
Open the water tap.
Seat aegergent but a load to remove post manufacturing resiActivate / De-Activate the Buzzer

An accoustic signal informs about the end of a programme. This signal can be switched off.
Refer to section HOW TO ADJUST SETTINGS and select the b-setting:
If the display shows bO the signal is switched off.
If the display shows b I the signal is switched on.

Different Settings for Rinse Aid

Rinse aid is added during the last rinsing phase to dry the dishes without streaks and stains.

Detergent (e.g. powder, tablets, …)

requires separate rinse aid
Factory default setting: d5. No settings are necessary.
The rinse aid is added from the rinse aid dispenser only.
Detergent with multifunction (e.g. Multitabs) combine detergent and rinse aid:
The rinse aid setting should be adjust to de. Please use the setting instructions in section HOW TO ADJUST SETTINGS and select the d-setting.
The rinse aid is added from the rinse aid dispenser in addition to the multitabs rinse aid.
Setting d- cuts off the rinse aid dosage and the rinse aid indication.
The higher the value for d the higher the dosage.
Usually the recommended setting performs well. In case of streaks, stains, shimmer etc.; refer to section TROUBLESHOOTING.
How to fill the Rinse Aid Dispenser

caution

Only use rinse aid for dishwashers.
Other products can cause damage to the appliance!

Press the release button (B) to open the lid.
Fill the tank (A) up to the ‘max’ mark.
Remove any spilled rinse aid with an absorbent cloth. Overdosed or spilled rinse aid may cause problems creating foam
Close the lid. Make sure that the release button locks into position.

How to Adjust Settings

To adjust the Rinse Aid level

The appliance is switched off.
Press and hold and about 3 seconds until:
- The display shows the current Rinse Aid setting (the default is d5).
Press to change the Rinse Aid setting in steps between d- (minimum dispense) and d5 (maximum dispense).
To exit the Rinse Aid menu, press and hold for I second.

Activate / De-Activate the Buzzer

The appliance is switched off.
Press and hold and for about 3 seconds until :
- The display shows the current Rinse Aid setting.
Press to scroll to the buzzer menu.
The display will show bU(buzzer off) or b / (buzzer on).
Press to toggle between bO (buzzer off) or b i (buzzer on).
To exit ,press and hold I second .

Child lock
This feature disables all the buttons on the dishwasher. If any other buttons are pressed while Child lock is activated, the Child lock indicator will flash for a few seconds.

To activate Child lock, press and hold for 3 seconds.
The display will remain on (if no programme has been started it will continue to flash while the control panel is locked).
To cancel Child lock, press and hold for 3 seconds.

Daily Use

Please note that not all sales models comes with identical features and options. So pictures of that chapter are sometimes different to your dishwasher model. Explanations try only to point out basic model variants.

Load the baskets.
Press the ON/OFF button to activate the appliance.
- If the rinse aid indicator is on, fill the rinse aid dispenser and reset the rinse aid indicator; refer to section HOW TO RESET THE RINSE AID IDNICATOR.
Add the detergent; refer to section DETERGENT.
Close the door.
Set the programme according to the type of load and how dirty the dishes, cups and cutlery are.
Maybe select a start delay time.
Press the START / PAUSE button to start the programme.
After programme end the appliance change to auto off. Unload the baskets.

How to Reset Rinse Aid Indicator

The appliance is switched on.
The rinse aid indicator is on:

Always completely fill the rinse aid before starting the next wash cycle.
Press and hold the START/PAUSE button until the Rinse Aid indicators light up. The Status Indicators light up.

Load the Baskets

With delicate glasses and porcelain make sure they are labelled dishwasher-proof.
Do not put in the appliance items made of wood, horn, aluminium, pewter and copper.
Do not put in the appliance items that can absorb water (sponges, household cloths).
Only use the appliance to wash items that are dishwasher-safe.
Remove remaining food from the items.
Soften burned food on the items before washing.
Put hollow items (cups, glasses and pans) with the opening down.
Put items with deep hollows in a slanted position.
Mix spoons with other cutlery to prevent them to bond together.
Make sure that cutlery and dishes do not bond together and there is a gap between each item.
Make sure that glasses do not touch other glasses.
Put small items in the cutlery basket.
Put light items in the upper basket. Make sure that the items do not move.
Make sure that the spray arms can move freely before you start a programme.
If jingling noises are heard during a programme run: Check that the dishes and glassware have a firm position.
Place heavily soiled items (like pots and pasket. Thin mople es in the bay int provides a better dishwashing result.
Told dover basse sakes do improve arrangement of pots, pans and bowls.

Cutlery Basket

Mix spoons with other cutlery to prevent them to bond together.
Use the grid element in order to separate the cutlery.
Place cutlery with the handles down for better washing results.
If long items may block the spray arms find a horizontal positioning in the upper basket.

CAUTION!

Put sharp and pointed items with the blade pointing downward to keep them out of harm’s way.

Upper Basket and utensil tray

The upper basket is designed to hold items like glasses, cups, saucers, plates, small bowls and shallow pans.
Use the utensil tray to securely hold long or sharp items like knives, chopsticks, or ladles. Ensure that knife blades are facing down.
Slide or remove the utensil tray if you need the space for other items below.
You can adjust the height of the upper basket to create more space for tall items in the lower basket.
For best washing results place the table knifes in the knife rack.
Place small items on the foldable cup holder.

CAUTION!

Place sharp and pointed items with the blade pointing down- ward into the knife rack, to keep them out of harm’s way.
Model with lever for easy height adjustment of the upper basket.

HDW 15V2 / HDW15V3 :

Pull out the upper basket.
Hold the basket on both sides on the edge above the lever.
Lift the basket till you hear a click.
Check the horizontal position and safe lock of the basket.

Lower the basket

Press the lever on both sides to lower the basket.
Check the horizontal position and safe lock of the basket.

The third Basket

The third basket can be pulled out, it is easy to put down and take out the cutlery.
Depending on the model, you can take out the third basket.
Depending on the model, you can take out the left and right side shelves to provide more room for taller goblet.

Detergent

Please use only a dedicated dishwasher detergent and follow the related instructions and dosage on its package.

If the lid is closed press the release button (A) to open the lid.
Put any detergent into compartment (B).
If the programme has a pre-wash phase, put a small quantity of detergent on the inner part of the appliance door. Refer to section PROGRAMMES.
Close the lid. Make sure that the release button locks into position.

Multitabs

These Multitabs detergent tablets could include two different agents for water softening, rinse aid and other functions. The softener and rinse aid setting must be adjusted according to section BEFORE FIRST USE.
Usually the default setting performs well. If there are streaks, stains, shimmer etc.; refer to section TROUBLESHOOTING and BEFORE FIRST USE.
Detergent tablets do not fully dissolve with short programmes. That may cause bad washing results and detergent residues.

If detergent without multifunction should be used again:

Save 3 to 5 tablets
Adjust the softener and rinse aid setting according to section BEFORE FIRST USE.
Use Multitabs detergent tablets for the next 3 to 5 wash cycles.

Start a Programme

Close the door.
Press the ON/OFF button
Press the program button you want to select and then the required programme indicator lights up.
Additionally the display flashes the programme run-time.
If desired select a start time for a delay start. Refer to section START A PROGRAMME WITH DELAY.
Press the START/PAUSE button to activate the programme or the delay start.
- The programme starts. The display acts now as countdown of the remaining run-time.

Interrupt a Running Programme

To interrupt a programme run:

Press the START/PAUSE button lI. In the display P is flashing. and/or
Open the door. The displayed cycle time is flashing.
Press the START/PAUSE button ll and/or close the door to continue the programme from the point of interruption. Longer breaks may cause bad cleaning results.

Activate / Deactivate options

On some models, the combination of all options is possible with all programmes. You can set one option or combine all options.

Switch on the appliance.
Press any of the currently extinguished washing procedure icons to select the washing procedure.
- The display shows the duration of the programme.
If needed, press any unlit additional function button (1/2, wash block, increase the brightness.
- If it can be matched with the current washing procedure, the additional function indicates that the icon will be lit, and if it cannot be matched, it will not be lit.
If the currently selected washing procedure is rapid washing, washing and single rinsing, press the and add the button, the washing time can be increased by 10 minutes at a time ,up to three times .
Press the button l| to start the program.

Start a Programme with Delay

Set a start time by the following procedure in order to delay a programme start:

Set a programme.
Press and hold the reservation button until the display flashes the required delay time (from | to 24hours).
Press the START/PAUSE button .
- The display shows the countdown of the start delay. The count down decreases with steps of I hour.
When the countdown is completed, the programme starts.

Cancel a Delayed Start

When the current reservation time is displayed for 24h, press the reservation button again to cancel the reservation
Afterwards the display flashes with the duration time for the set programme.
The selected programme starts after a few seconds

Cancel Start Delay / Programme

Press the ON/OFF button for about I second.
- The start delay is cancelled.
- The programme is aborted.
- The appliance is switched off.

Start a new programme and a delayed start if desired.
CAUTION!
If a programme will be aborted in the process of washing dishes, the residue of detergent remains on the dishes. These can cause damage to health! Make sure to rinse off the detergent residues completely before using these dishes again.
Make sure that there is detergent in the detergent dispenser before start a new programme.
End of Programme
When the programme is completed, the display shows 000 and an ac- coustic signal is heard (if it is not switched off). The display switches off.

Press to switch off the appliance or the appliance switches into standby mode automatically after 2 minutes.
Open the door:
- CAUTION!
- If the door will be opened immediately after the end of programme, hot steam can escape. Danger of scalding!
- Open the door carefully!
Remove dishes:
- Open the door slightly and leave it ajar (about 100 mm) to help the drying process.
- Let the dishes become cold before removing them from the appli- ance. Hot dishes damage more easily.
- First remove the items from the lower basket, then from the upper basket.
- There can be water on the sides and on the door of the appliance.
- Stainless steel becomes cool more quickly than the dishes.

Standby Mode

The switched on appliance will go into standby mode if it is not activated within 2 minutes before starting a programme, or at the end of a programme.
This saves energy.
The display switches off.
To interrupt the standby mode push one button.

Care and Cleaning

In for are clue your palia diverse pra les i spely die erens.
clogged or blocked spray arms significantly decrease the washing results.

Care and Cleaning the Filters

There are three filters (Al.A2. B) to be checked and cleaned.

Turn the filter A anticlockwise and remove it.
To disassemble the filter A press the latches and unplug A I from A2.
Remove the filter B.
Clean the filters with water.
Put the filter B to its initial position.
Assemble the filter A and put it into position in filter B. Turn it clockwise until it locks.

An incorrect assembly or position of the filters will cause bad washing results and possibly serious damage to the appliance.
If any filter is removed make sure that no solid object of any size is left beyond these filters!

Care and Cleaning of the Spray Arms

Spray arms should be regularly inspected for dirt. If needed the spray arms could be removed.

Upper spray arm

Turn bayonet socket to the left to remove spray arm.
Remove remaining parts of foodremnants with a thin pointed object.
Flush with water and check all the holes are clear.
Turn bayonet socket clockwise to fasten spray arm.

Lower spray arm

Pull at the center to remove spray arm.
Remove remaining parts of food remnants with a thin pointed object.
Flush with water and check all the holes are clear.
Place spray arm at the center with a light push.

External Cleaning

CAUTION!

Never clean the appliance with a steam cleaner.
Never use bleach or other chlorinated detergents.
Clean the appliance with a damp soft cloth.
Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads or solvents.
Clean the door seal with a damp soft cloth.

Troubleshooting

Many occuring problems could be solved by yourself without specific expertise.
In case of a problem please check all shown possibilities and follow below instructions before you contact an after sales service

CAUTION!

Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket.
Electrical equipment should be serviced only by qualified electrical experts, because improper repairs can cause considerable consequential damages.

The appliance does not start, or it stops during operation

Problem	Possible cause	Possible solution
The programme does not start.	Appliance door is open.	Close the appliance

door.
Delay start is set.| Refer to displayed time.
Mains plug is not connected in the mains socket.| Connect the mains plug.
Fuse in the house circuit is damaged.| Replace the fuse.

Rinse Aid Indicator is lighted.

| Rinse aid dispenser is empty.| Refill Rinse aid until full
****| Press and hold the START/ PAUSE button for 3 sec after

Error codes on the display

All other Alarmcodes:

Note Alarmcode
Contact Service ; refer to CUSTOMER SERVICE

Washing Results are not satisfactory

Problem	Possible cause	Possible solution
The dishes are not clean.	Filters are clogged.
Filters are not correctly assem- bled and installed.	****

correctly assembled and installed.

Spray arms are clogged.| Remove remaining food remnants with a thin pointed object.
Programme was not applicable for the type of load and food remnants.| Make sure that the programme is applicable for the type of load and food remnants.
Incorrect position of the items in the baskets.Water could not wash all items.| Make sure that the position of the items in the baskets is correct and that the water can easily wash all items.
Spray arms could not turn freely.| Make sure that the position of the items in the baskets is correct and does not cause the blockage of the spray arms.
No detergent or insufficient quantity of detergent in the deter- gent dispenser.| Make sure that you add the correct quantity detergent in the dispenser before you start a programme.
The wash cycle was interrupted by a long break.| Do not open the door or cut power supply during the wash cycle.
Whitish streaks, stains or bluish layers on glasses and dishes.| Released quantity of rinse aid is too much.| Decrease the released quantity of rinse aid. Refer to section DIFFERENT SETTINGS FOR RINSE AID.
Quantity of detergent was too much.| Make sure that you add the correct quantity of detergent in the dispenser before you start a programme.
Multitab detergent tablets used with a short programme might not fully dissolve.| ** Select a longer programme when using Multitab detergent table.ts
Problem| Possible cause| Possible solution**
---|---|---
Dry water drop stains on glasses and dishes.| Rinse aid dosage is too low.| Increase the released quantity of rinse aid. Refer to section DIFFERENT SETTINGS FOR RINSE AID.
Quality of rinse aid or Multitab.| Cleaning product too old; change the product.
The dishes are wet.| • Programme had no drying phase.

• Programme had a low temperature drying phase.

| Open the door slightly and leave it ajar (about 100 mm) to help the drying process.
The dishes are wet and matte.| Rinse aid dispenser is empty.| Refill rinse aid into the dispenser and reset the rinse aid indicator.
Quality of rinse aid or Multitab.| Cleaning product too old; change the product.

Economic and Environmental Use

It is not recommended to pre-rinse the dishes under running water.
Select the washing programmes by type and degree of contamination of the dishes.
Select the economy mode programme ECO for normal soiled items.
The most economically use you will have with full loading.
Open the door slightly and leave it ajar (about 100 mm) to help the drying process.
Only use the manufacturer’s recommended detergent or rinse aid dosages.

Installation

WARNING!

Any installation may be carried out only by a qualified technician; refer to section SAFETY.

Free Standing Installation

Install the appliance on solid ground. Adjust accurately all feet to get a firm, horizontal position.

INFORMATION!

Only with a correct level the appliance door closes and seals correctly.

Installation under Worktop

The dimensions of the recess should at least agree with the dimensions in the figure.
Put the appliance adjacent to the slot. Make sure that all connections (water, drain water, power) are neatly positioned and connected.
Optional: Remove the worktop of the appliance.
Adjust accurately all feet to get a firm level position.
Install the appliance carefully into the recess.

WARNING!

If used as free standing appliance again, the worktop must be remounted.

Fresh Water Connection

IMPORTANT!

The appliance should be connected to the water main using the new water inlet hose supplied. Old hoses should not be used.
Do not shorten the inlet hose

Take note of water connection requirements.
- The dishwasher has a single valve water connection.
- We recommend a cold water connection for best performance and energy efficiency.
- The incoming water temperature should not exceed 25°C.
Take note of the permitted water pressure extremes.
- Lowest: 0.3 bar = 3 N/cm = 30kPa
- Where pressure is below I bar, contact a qualified plumber.
- Highest: 10 bar = 100 N/cm’ = IMPa
- Where pressure is above 10 bar, a pressure reduction valve must be installed. Contact a qualified plumber.
Connect the water inlet hose to an accessible water tap with a 3/4″ BSP connector (see fig.A). Ensure that there is no kink in the inlet hose that could restrict the flow of water. A 90° bend requires a minimum height of 200 mm for a kink-free curve.
- Ensure incoming water is clear. If the water pipes have not been used for a long period of time, let the water run to make sure it is clear with no impurities. Not doing so may result in the water inlet hose getting blocked and damaging the appliance.
- If required, use a filter insert to filter out deposits from the piping. The filter insert is available from your Authorised Service Centre or Customer Care.
Tighten the hose coupling a further half turn after seal contact.
Check that the connection does not leak.
- Some models are fitted with an “Aquastop” water supply hose (see fig.B) in which the small filter is already housed in the threaded end.

Anti-Flooding protection

The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, in order to prevent damage to your home. If for any reason the box containing the electrical components happens to get damaged, turn off the power supply and remove the plug for the appliance from the socket immediately. In order to guarantee that the anti-flooding feature operates properly, the “A” box with water supply hose must be attached to the water supply tap as shown in fig.B. No other type of connection is acceptable. The water supply hose must not, under any circumstances, be cut, as it contains electrical parts which are live. If the length of the hose is not adequate to make a proper connection, the hose must be replaced with one which is long enough. This hose is available upon request from specialised retailers and Authorised Service Center.

Drain Water Connection

Fix the water drain hose properly to the piping. The hose has to reach at one point a height between 400 and 850 mm above the appliance bottom line!
An extension hose for the water drain hose must not exceed a total length of 4 m and must have the same diameter as the water drain hose.

Following connections are possible:

Drain hose to sink

Hang the drain hose with the U-support over the edge of a sink with adequate size.
Protect the U-support sufficiently against slipping.
Drain hose to waste water connection
The internal diameter of the stand pipe with vent-hole must be minimum 40 mm.
Put the drain hose for approx. 80 mm in the wastewater pipe.
Attach the U-support and secure it sufficiently.

Drain hose to sink connection

When connecting the drain hose to a sink trap with a drain hose spigot, make sure that the drain hose is supported to the height of the bench.
Ensure the drain spigot has a minimum hole diameter of 15 mm and it has been drilled out.

CAUTION!

Ensure always that all connections (power supply, drain and fresh water hose are firm, dry and leak free!
Take care these parts are never to be crushed, kinked, or twisted
If the supply cord is damaged, it must be replaced by the service agent (see warranty card) in order to avoid a hazard.
Check the electrical data on the rating label (located on the left-hand side of the dishwasher’s stainless steel inner door). Should the data on the rating label be different to those specified below, consider those on the rating label as correct.

Suppliers name

or trade mark

| Haier
---|---
Supplier´s model identifier| HDW15V2| HDW15V3
Rated capacity in standard

-place settings

Stainless Steel

|

HDW15V2W1 /HDW15V2S1 /HDW15V3W1/HDW15V3S1

Customer Service

We recommend our Haier Customer Service and the use of original spare parts.
If you have a problem with your appliance, please first check section

TROUBLESHOOTING.

If you cannot find a solution there, please contact your local dealer or the Service & Support area at www.haier.com.au or at www.haier.co.nz
where you can activate the service claim and also find FAQs.
To contact our Service, ensure that you have the following data available.
The information can be found on the rating plate at the door.
Model——————————-
Serial No.—————————

Standards Test

Haier-HDW15V2-Dishwasher-fig-41

Recommended loading patterns

Wash programme| Eco When the programme is finished, open the door 100mm to help with drying
---|---
Powdered detergent quantities| 5 g pre-wash + 28.75 g main wash
Rinse aid dosage level| (HDW15V3)
Maximum number of place settings| 15
Height adjustment of upper basket| Ensure the upper basket is in its lower most position

Recommended loading patterns