CONTECH LIGHTING Slim Downlight Series Round Baffle Instruction Manual

June 16, 2024
CONTECH LIGHTING

CONTECH LIGHTING logo Slim Downlight Series Round Baffle
Instruction Manual

Slim Downlight Series Round Baffle

CONTECH LIGHTING Slim Downlight Series Round Baffle INSTALLATION INSTRUCTIONS
Slim Downlight Series: Round Baffle
The important safeguards and instructions here are not meant to cover
all possible conditions and situations that may occur.

IMPORTANT SAFETY INSTRUCTIONS:

  • WARNING: RISK OF FIRE AND ELECTROCUTION
  • WARNING: TO AVOID FIRE, SHOCK OR DEATH, disconnect power at circuit breaker before installing or servicing device
  • READ AND SAVE THESE INSTRUCTIONS FOR LATER USE
  • Product should be installed by an electrician
  • All electrical connections must be in accordance with local and National Electrical Code (NEC) standards. If you are unfamiliar with proper electrical wiring connections, consult an electrician.
  • Product must be grounded to avoid potential electric shock and any other potential hazards
  • Product must be mounted in locations and at heights and in a manner consistent with its intended use, in compliance with National Electrical Code and local codes and where it will not readily be subject to tampering by unauthorized personnel
  • This device is not intended for use with emergency exits
  • Do not open the Slim Downlight; there are no serviceable parts inside. Any changes or modifications can void the warranty.
  • Do not exceed the input rating of the luminaire
  • Connect to a 120V 60Hz power source only; any other connection will void the warranty
  • To prevent damage to the wiring, do not expose wiring to edges of sheet metal or other sharp objects
  • Wear rubber soled shoes and work on a sturdy wooden or nonconductive ladder
  • Ground the fixture to avoid potential electric shocks and to ensure reliable starting
  • Double check all connections and screws, ensuring they are tight and correct
  • Most dwellings built before 1985 have supply wire rated at 60°C
  • Supply conductors (power wires) connecting the fixture must be rated at minimum of 90°C
  • Installing contrary to instructions may cause unsafe conditions
  • If the product has any visible damage do not install it
  • Call the Technical Support department at ConTech Lighting with any installation questions: 847.559.5500

INSTALLATION PROCEDURE

FIGURE 1

  • Use the template (included) to mark and cut the opening in the ceiling

CONTECH LIGHTING Slim Downlight Series Round Baffle - FIGURE
1

FIGURE 2

  • Remove the Junction Box knock-outs for wiring and open the Junction Box
  • The Junction Box contains three (3) Wires: Hot (black), Neutral (white) and Ground (green)
  • Connect Supply Wires to Junction Box Wires; ALWAYS SPLICE BLACK TO BLACK (hot to hot) and WHITE TO WHITE (neutral)
  • Connect the Ground (green) Wire to Ground (green) Wire in the Junction Box; replace Cover

CONTECH LIGHTING Slim Downlight Series Round Baffle - FIGURE
2

INSTALLATION PROCEDURE, CONTINUED

FIGURE 3

  • Connect downlight to junction box with the quick-connect cable
  • Select the Color Temperature (CCT) using the 5CCT Switch on the Junction Box
  • Place Junction Box into ceiling

CONTECH LIGHTING Slim Downlight Series Round Baffle - FIGURE
3

FIGURE 4

  • Push the “Easy Mount” clips up on the luminaire
  • Insert downlight into ceiling and release clips to secure downlight in ceiling

CONTECH LIGHTING Slim Downlight Series Round Baffle -
FIGURE4

INSTALLATION PROCEDURE FOR OPTIONAL MOUNTING PLATE ACCESSORY

  • The New Construction Plate can be used to provide extra support for a variety of sizes (4, 6 and 8 inch)
  • Select the luminaire hole size by matching the luminaire to the rings on the frame kit
  • Select the ring that is slightly smaller than the outer diameter of the fixture
  • Using a pair of cutters, cut the ring out that corresponds to the luminaire being installed

CONTECH LIGHTING Slim Downlight Series Round Baffle -
FIGURE5

FIGURE 1: CEILING JOIST INSTALLATION

  • Lay the frame kit on the ceiling joist in the desired location and secure to joists
    NOTE: Allow enough space for the Junction Box mounted on the Mounting Plate

CONTECH LIGHTING logoCONTECH LIGHTING | 725 LANDWEHR ROAD
NORTHBROOK, ILLINOIS 60062
PHONE 847.559.5500 | www.contechlighting.com
©2023 Conservation Technology of Illinois, LLC. All rights reserved.
Note: Specifications subject to change without notice.
WFBR INST REV0423
All specifications subject to change without notice.
For ConTech’s limited product warranty, go to
www.contechlighting.com.
For a printed copy of the warranty,
call 1-847-559-5500.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals