URVOLAX UR65X 100 Percent Wireless Reversing Camera User Manual
- June 16, 2024
- URVOLAX
Table of Contents
DIGITAL WIRELESS BACKUP
CAMERA SYSTEMS
User Manual / Installation Instructions
UR65X
Please read this manual thoroughly before operating the device,
and keep it for future reference.
Please Do Bench Test before Installation in Vehicle
**Introduction
**
Thanks for purchasing URVOLAX Digital Wireless Backup Camera Systems! With
this manual, you will be able to properly install and operate the unit.
Digital Wireless Connection – the product adopts latest car point to point
wireless connection technology, there is no interference with other wireless
devices.
The camera with built-in battery achieve 100% wireless and no need to connect
the reversing light, the magnetic base allow to stick on the vehicle without
drilling a hole. When the vehicle is in reverse, the image is wireless
transmitted to the monitor. Monitor is directly powered from the cigarette
lighter socket or ACC, No need to run any wires from the camera to the
monitor.
Our reversing camera kit can provide reliable security for your journey.
Enjoy using our products!
What’’s in the Box
- DU AW oN e
- 7 inch IPS Monitor
- Backup Camera
- Monitor U-shaped bracket
- Monitor Swivel Head bracket . Car Charger
- Sunshade
- User Manual
- Power cable
- Antenna
- U-shaped bracket Installation Kit
- Installation tool
- Remote control / Iron and glue
Monitor Operation
| Button | Function |
|---|---|
| POWER | Turn the monitor ON/OFF |
| Brightness “-“, Adjust settings, Long press 8S to flip the menu | |
| Brightness “+”, Adjust settings | |
| CH- | Switch channel |
| MENU | 1.Menu setting 2.Back to previous page |
3.Long press to enlarge Xi. X1.5 X2.0 X3.0
SEL| 1.Confirm key 2.Setting SD card to start/pause recording
3.Long Press for Parking Line Adjustment
MENU
※PAIRING
- Long press to power on the camera, it will enter one minute pairing mode. (The infrared lights will turn on when cover the lens).
- “CH-” to select the channel to be pairing
- “MENU””PAIRING””SEL” to confirm connection
- Start pairing
- The image will display automatically once match
Please turn ON the camera again and repeat the pairing steps if the connection
do not completed at the first time.
If need to connect multiple cameras, please switch to the corresponding
channel at step 2.
※ PICTURE
Press “SET” to confirm the choice, and adjust the “BRIGHTNESS” “CONTRAST””HUE”
by “↑””↓”
※MIR-FLIP
The image can be rotated for viewing when the camera is on different
direction.
※ MODE
Different display mode for split screen.
※ CAM-SETUP
If turn OFF the camera, it will not display when switch channel at home page
SCANTIME: The time (seconds) for the cameras switching automatically.
Only work when the AUTOSCAN is ON.
AUTOSCAN: Turn ON to switch the camera image automatically. Only work for the
cameras which already activated.
※SYSTEM
DELAY TIME: System setting Only, will not influence the image transmission,
please no need to adjust this value.
DEFAULT: All the setting will be back to default when the device reboot.
※Play
Playback the recording videos, each video clip is one minute.
The remianing storage space can be checked on the top of this page.
※ RECORD
REWRITE: The video will be loop recording by rewriting the oldest files when
the memory card is full.
FORMAT: Format the memory card.
*Recording Function
-
5D Card Slot
Open the SD card slot on the monitor back with the small blue screw-driver, insert the adapter and micro SD card for recording.
High-speed $D card of class 10 or above (Less than 128G) is recommended.
Please make sure to UNLOCK the Adapter before inserting the SD Card.
The format allocation unit of the micro SD card should be set in exFAT 32/64KB, other value is not compatible for the recording function. If you need free adapter and micro D card, please feel free to contact us: service03@urvolax.cn -
SD Card Status
-
“SEL” to start/stop recording
Camera Operation
※Turn ON/OFF by long press the power button
Camera ON: The red dot at the left side will light on first, then the yellow
dots will light on to show the remain power, and then enter the pairing mode
for one minute, the eight infrared lights will turn on when cover the lens or
in the dark.
Camera OFF: The red and
yellow dots will flash together and enter the sleeping mode.
* Warm Tips to SAVE Camera
Battery & REDUCE Recharging Times:
We suggest to turn OFF the red button of the cigar charger when NOT in
reversing or no need to view the screen.
If SD card i inserted, please pause the recording when do not need this
function.
※Please make sure to attach both TWO antennas to the camera and monitor
accordingly, otherwise the signal transmission will be influenced.
※Recharge by TYPE-C
usb cable (included)
※The camera angle can be adjusted by loosing the button at the right side.
Remote Control Key Operation
※Please operate the remote
control to the signal source of the screen
Installation Tool
- Removable Sunshade
- 0ption 1 to mount the monitor: U-shaped bracket
- 0ption 2 to mount the monitor: Swivel Head bracket
- Magnetic iron piece
If the position you would like to install can not attract the magnetic camera,please stick the included magnetic iron piece on the specific position for attaching the camera.
Connection Method
Specification
| Power Supply | DC12to 36V |
|---|---|
| Wireless Frequency | 2.4 GHz |
| 2.4G Wireless network range | 2403-2480MHz |
| Wireless Range | 300m(open area) |
| Delaying Time | <200ms |
| Operating temperature | -20°C~ 80°C |
CAMERA
| Image Sensor | 1/3 inch |
|---|---|
| Waterproof Rating | 1P69K |
| View Angle | 130°[H] 170°[D] |
| Camera Pixel | 1000TVL |
| Charging voltage | sv |
MONITOR
| LCD Size | 7Zinch IPS |
|---|---|
| Resolution | 1280(H) x 1024(V) |
| Contrast | 500:01:00 |
| Brightness | 500cd/ m² |
| Response Time | 25ms |
| Power Consumption | <500mA |
Troubleshooting
| Problem | Solution |
|---|---|
| Monitor Won’t turn on | Check the cigarette lighter has 12-36V DC Output |
Check the fuse in the Cigarette socket adapter
Camera and Monitor won’t pair| Check if the camera is receiving power
Make sure to follow the instructions to operate the Pairing
Weak Signal| Check if the camera and monitor antennas are installed
Distance between camera and monitor is too far. Reduce distance between camera
and monitor
Large dense objects could be obscuring the signal. If possible, move the
objects
Interference from overhear power lines may be affecting the signal
Try unpairing and pairing
Night Vision is poor| The night sensor on the camera may be dirty or
obstructed
Ensure the camera is installed at least 2 inches away from rear lights
Dark Picture| Check whether brightness and contrast are adjusted correctly
Warranty Card
https://mailchi.mp/cea0e7884b64/urvolax
Scan for 1-Year Warranty
We offer 1-year warranty and lifetime technical support for this product.
Please scan the QR code above to activate the 1-year warranty within 2 WEEKS
upon product receipt.
Should you have any general or technical questions about this product, please
feel free to contact us as following:
CUSTOMER SUPPORT
Email: service03@urvolax.cn or
service02@urvolax.cn
Company TEL:(0086)769 2198 6525