Lincat CiboPlus High Speed Oven Instruction Manual

Lincat CiboPlus High Speed Oven

IMPORTANT INFORMATION

• Read these instructions carefully before using this product, paying particular attention to all sections that carry warning symbols, caution symbols, and notices. Ensure that these are understood at all times.

• WARNING!
  This symbol is used whenever there is a risk of personal injury.

• CAUTION!
  This symbol is used whenever there is a risk of damaging your Lincat product.

• NOTE:
  This symbol is used to provide additional information, hints, and tips.

KEEP THIS MANUAL FOR FUTURE REFERENCE
This manual contains important safety and installation-operation instructions. All users/operators should be required to read this manual before operating the oven. Failure to follow the instructions contained in this manual may cause injury or death, and damage to the oven and will void the warranty.

IMPORTANT SAFETY INSTRUCTIONS

When using electrical appliances basic safety precautions should be followed, including the following:
WARNING – To reduce the risk of burns, electric shock, fire, injury to persons, or exposure to excessive microwave energy.

1. Read all instructions before using the appliance.
2. Read and follow the specific “PRECAUTIONS TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY” found.
3. This appliance must be grounded. Connect only to a properly grounded outlet. See “GROUNDING INSTRUCTIONS” found.
4. Install or locate this appliance only by the provided installation instructions.
5. Some products such as whole eggs and sealed containers ± for example, closed glass jars ± can explode and should not be heated in this oven.
6. Use this appliance only for its intended use as described in the manual. Do not use corrosive chemicals or vapors in this appliance. This type of oven is specifically designed to heat, cook, or dry food. It is not designed for industrial or laboratory use.
7. HOT CONTENTS CAN CAUSE SEVERE BURNS. DO NOT ALLOW CHILDREN TO USE THE MICROWAVE. Use caution when removing hot items.
8. Do not operate this appliance if it has a damaged cord or plug if it is not working properly, or if it has been damaged or dropped.
9. This appliance should be serviced only by qualified service personnel. Contact the nearest authorized service facility for examination, repair, or adjustment.
10. Do not cover or block any openings on the appliance.
11. Do not store this appliance outdoors. Do not use this product near water ± for example, near a kitchen sink, in a wet basement, near a swimming pool, or similar locations.
12. Do not immerse the cord or plug in water.
13. Keep the cord away from heated surfaces.
14. Do not let the cord hang over the edge of the table or counter.
15. When cleaning surfaces of the door and oven that come together on closing the door,use only mild, nonabrasive soaps, or detergents applied with a sponge or soft cloth,
16. To reduce the risk of fire in the oven cavity:
    • Do not overcook food. Carefully attend to appliances when paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking.
    • Remove wire twist-ties from paper or plastic bags before placing the bag in the oven.
    • If materials inside the oven ignite, keep the oven door closed, turn the oven off, disconnect the power cord, or shut off power at the fuse or circuit breaker panel.
    • Do not use the cavity for storage purposes. Do not leave paper products, cooking utensils, or food in the cavity when not in use.
17. Liquids, such as water, coffee, or tea can be overheated beyond the boiling point without appearing to be boiling. Visible bubbling or boiling when the container is removed from the microwave oven is not always present. THIS COULD RESULT IN VERY HOT LIQUIDS SUDDENLY BOILING OVER WHEN THE CONTAINER IS DISTURBED OR A UTENSIL IS INSERTED INTO THE LIQUID.

SAVE THESE INSTRUCTIONS

• Do not cook directly on the glass base. Use a Teflon or similar lining sheet.
• Do not use metal tools to clean the glass base. Do not hit the glass base.
• Never use any metal, one-use plastics or aluminum foil in this oven unless Lincat approved.

Do Not Operate the oven if it is damaged

The oven door closed properly and there must be no damage to the:

1. Door structure or microwave choke on the inside of the door
2. Hinges or latches (broken or loosened)
3. Door seals and sealing surfaces

Planned Maintenance
Periodic preventive maintenance is essential in maintaining peak performance. It is necessary to keep the motors, fans, and electronics free of dirt, dust, and debris to ensure proper cooling. Overheating is detrimental to the life of all the components mentioned. The periodic intervals for preventive cleaning may vary depending on the environment in which the oven is operating.

Do not cook large quantities of raw meat in this oven. The oven is fitted with a catalytic converter that can become blocked and ineffective if excessive amounts of fatty foods such as burgers and sausages are cooked. Lincat recommends re-heating cooked proteins.

Technical Data and Specifications

External Dimensions, Weight, and Power

• Height (inch): 25.2″
• Width (inch): 15.6″
• Depth (inch): 26.1″ + 2.4″ handle
• Weight (lb): 114.7
• Power rating: 3kW, 208-240V, 60Hz

Internal oven cavity dimensions

• Height (inch): 4.6″
• Width (inch): 13.2″
• Depth (inch): 13.6″

Technical Pictures

Installation and Commissioning

This appliance must be earthed.

An equipotential bonding terminal is provided to allow cross-bonding with other equipment.

If replacing the plug connect the terminals as follows:

• Green and Yellow wire Earth E
• Black wire L1
• White wire L2

Supply cords shall be oil-resistant, sheathed flexible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57)

Install this appliance on a level surface ensuring all vents are unobstructed. Ensure that the surface is capable of safely supporting the weight of the appliance. Any partitions, walls or furniture must be of non-combustible material. Minimum distances: A 2´, B 2´ ± see Fig 1. The appliance is not intended for built-in installation.
Do not locate the oven directly next to dusty / flour-based preparation areas.

We recommend you always cook on the Teflon sheet or tray. Never cook directly on the glass base.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
WARNING ± Improper use of the grounding can result in a risk of electric shock. Consult a qualified electrician or serviceman if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded, and either:

1. If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3- 3-blade grounding plug, and a 3-slot receptacle that will accept the plug on the appliance. The marked rating of the extension cord shall be equal to or greater than the electrical rating of the appliance.

What’s in the box

• CiBO+ oven
• This Instructions Manual IS814
• Quick Start and Recipe Book
• Loading Paddle LT05
• Air filter grill GR68

Accessories, Consumables and Codes

General layout

• A – Door Handle
• B – Touchscreen display
• C – On/Off button, Press and hold for 3 seconds
• D – Air filter, must always be fitted when the oven is switched on
• E – USB port (behind air filter)

To access the USB port, remove the air filter. The air filter is fitted on a keyway – to detach it, push upwards and then pull forward.

• F – Air Outlet, do not block
• G – Limit thermostat
• H – Mains supply
• I – Stand-off spacer

Only qualified or trained personnel should use this appliance.

Quick start guide

Quick start guide – Switching on

• Make all the relevant safety checks and ensure the oven is clean and empty before
• proceeding. Spray the inside walls, base, and door inner with oven guard (OS01) Plug the oven into a wall socket and turn on the socket.
• Turn on the oven by touching and holding the On/Off button (Fig 2, C) for 3 seconds.
• The oven will beep once, and then show the CiBO+ logo followed by the Home screen.

The Home screen

• CiBO+ Tri Heat Cooking technology

• CiBO+ has three heat sources ± a twin oven element with power ratings of 500 and 1,500W, a 1000W output microwave magnetron, and a 700W heated base element.

• Not all the heat sources are powered on at the same time (the controller prevents this) and power is always limited to less than 13 amps, allowing a standard 13A plug to be used.

• CiBO+ can cook all types of food, however with a small cavity we advise against continual use for cooking proteins high in fat content as this will damage the catalytic converter.

• The concept behind operating the CiBO+ controller is that you simply touch whatever you want to change/select

• Cooldown and switch off. This is a special function to rapidly cool the oven down to 122°F (in around 10 minutes if the user opens the door), after which the oven automatically turns itself off.

• Recipe Manager. This accesses the individual cooking recipes and then the general settings for the oven via the settings cog in the bottom left-hand corner.

• ECO. This is displayed in the bottom left corner if the ECO mode is selected in the settings. It can be used to reduce electricity consumption during quiet periods

The home screen shows the first 8 recipes in the first group. Four more groups are selectable across the bottom of the screen.

Groups Explained

• On the home screen, you will find five recipe groups that you can name.
• Each group of eight recipes within the group share the same oven and base temperature settings, changing the settings will change the whole group.
• You can decide on the best working temperature and have multiple groups working at the same temperature if you wish.
• Individual recipes can have up to four steps to change airspeed to increase coloration to the outside of the food and the microwave power to heat through to the center of the product. Most foods only require one step.
• When a recipe is selected the oven heats to the oven and base temperature for that group.

Operation
To operate touch the required recipe. The oven will pre-heat to the set oven temperature (If the oven temperature is below the recipe temperature). Touching the oven/base set temperatures in the bottom right corner shows the current temperatures, touch again to return to the set temperatures. To minimise pre-heating it is suggested that the auto-preheat is turned on in the settings screen. This means the oven will maintain a set temperature and always be ready to cook.

• When the set oven temperature is reached the oven will beep, the screen will go green and the oven is ready to be loaded with product.

• Place the food in the oven and touch the ³Play´ button. The oven will cook the food to the selected recipe, the screen will go red and beep to tell you it is complete.

• Touch ³Stop´ and carefully remove the food from the oven. There is an auto-stop / reset to ready option in the settings menu.

Settings

Copying and moving recipes
From the Home screen, touch Recipe Manager to be presented with the Recipe Manager screen. This screen allows you to copy/move and edit recipes.

• Copy Touch the copy button and select the recipe to copy. Then select the position to copy the recipe to, this can be in any Group.
  Note. The base and oven temperature settings will be as per the group settings the recipe is moved to so cooking times may need to be adjusted.

• Move Touch the move button and select the recipe to move. Then select the position to move the recipe to, the other recipes will auto-arrange themselves. Move only works in the group you are working in.

• Settings Touch the settings button to access the general setup for the oven.

Recipe editing
This is a typical recipe.

To rename the group, touch the Group name (Snacks) on the right-hand title bar and use the keyboard to edit the title. Accept your changes with the ³Tick´. Touch the Save icon. Touch the Home icon to return to the Home screen.
To rename a recipe, touch the recipe name (Chicken Wings) on the top title bar and use the keyboard to edit the title. Accept \RXUFKDQJHVZLWKWKH³7LFN´ Touch the Save icon. Touch the Home icon to return to the Home screen. Recipes can have two lines of tex

To change the oven temperature settings of a Group

From a selected recipe, touch the temperature figures (bottom right side) and you will be presented with the Temperature adjustment screen (above).
Touch the temperatures you wish to change and adjust them with the slider bar.
Touch the Save icon and the Home icon to return to the Home screen. All recipes on that group will now use the new temperature settings.

• Oven temperature. This is the temperature for the oven and is adjustable between 86 and 518°F
• Base temperature. This is the temperature for the oven ceramic glass base and is adjustable between 86 and 644°F
• Save. 7KLVVDYHVWKHFXUUHQWVHWWLQJVLI\RXGRQ¶WZDQWWRVDYHWKHQHZ setting touch the back arrow

To edit individual recipes
From the Recipe Manager touch the recipe icon you wish to edit.

The Recipe editing screen consists of 4 rows of cooking stages (not all will need to be used for most recipes), with 3 columns to set Microwave Power, Fan Speed and Time.
Touch any of the numerals and they will become orange, to change them, edit with the slider bar. The cooking time for each stage will be incremented and added to the total recipe cooking time shown on the RH side below the recipe icon. When any value is adjusted, the Save icon will display. You now have 2 options. You can either touch Save and then return to the Home screen to try your new settings, or as an aid to quickly developing your recipes, you can try out the new settings without returning to the Home screen by touching the Play button. Once you are satisfied with the results of your trial recipe always remember to touch Save before returning to the Home screen.

• Microwave Power. This is a percentage value and can be adjusted in 10% increments from 0 to 100%
• Fan speed. This is a percentage value and can be adjusted in 10% increments from 0 to 100%
• Time. This is seconds and minutes-based and can be adjusted in 5-second intervals from 0 seconds to 30 minutes

To change a recipe icon
Recipe icons can be selected from a library to complement the product being cooked. To change a recipe icon, touch Recipe Manager and then the Recipe icon to be changed. Touch on the icon image in the top right corner to open the icon library. Select your new icon, touch Save, and then the Home icon to return to the Home page to see the new recipe icon.

General Settings
Your CiBO+ comes with many user-adjustable settings to allow of customisation the oven. To access the Settings menu, from the Home screen touch Recipe Manager and then Settings.

Settings Touch the settings button to access the general setup for the oven. This can be PIN-protected.

This is the settings screen showing the five subcategories. Touch the relevant arrow to advance to the next level.
Temperature and Control

• Auto Preheat. If this is set the oven will start to heat as soon as the oven is switched on and on the home screen. It is recommended this is selected as it improves the oven’s readiness to cook.
• Ready Temperature band. This is the range of temperature at which the oven is ready to receive food to be cooked. A value of 86°F is a good starting band. If the oven is repeatedly showing pre-heat after cooking then it may be increased.
• Measurement units. Touch to cycle between Celsius and Fahrenheit

Magnetron Energy delay. Selecting this adds a 5-second delay to the recipe start to compensate for the time needed for the magnetron to heat and start emitting microwaves.
ECO Settings. See explanation on next page.

Auto Preheat settings

• Enable Turns the Auto Preheat on and off. With it turned off the oven ZRQ WKHDWXQWLO a recipe is selected. It will then take approximately 10 minutes to get to a cooking temperature.
• Set Oven Temperature. Sets the default temperature between 86 and 518°F. Touch to change, use the slider, and save the new temperature. It is recommended that this is set to the most common cooking temperature being used.
• Set Base Temperature. Sets the default temperature between 86 and 644°F. Touch to change, use the slider, and save the new temperature. It is recommended that this is set to the most common cooking base temperature being used.
• Enable Soak. This sets a time after the initial heat-up to allow the oven cavity temperature to equalize. Enabling soak can give more repeatable results at the start of the cooking session. It only operates when the oven is first turned on.
• Soak time. Sets the soak time, up to 20 minutes. At least 10 minutes is recommended.

ECO settings
Eco allows you to save energy during quiet periods by reducing the temperature of the oven.

Enable. Turns ECO on and off

• Set Temperature. Sets the temperature the oven reduces to after no cooking activity within the Timeout time
• Timeout Time. The time allowed with no cooking activity before ECO is activated.
• When ECO is active the screen goes black and displays ECO in green in the center.
• To exit ECO just touch the screen and the unit will re-heat to the set temperatures.

Settings – Sound and Display
Sound and Display settings allow the user to configure volumes and screen appearance to their preference.

• Volume – Touch volume to toggle the level of the warning buzzer.
• Buzzer Reset Time – Touch the time to adjust the duration of the buzzer time. It is set to sound every 10 seconds for the duration of this time.
• End Program Warning Enable – This is a buzzer that warns the operator that the food is nearly cooked. Touch to switch the buzzer end of the recipe warning on or off. End Program Warning Time – Touch to set the time before the recipe ends to sound the buzzer.
• Door Open Stop / Start – When enabled, this function allows the opening or closing of the door to control the stopping and starting of the cooking recipe. Touch to toggle on/off.
• Screen Brightness – Touch to allow selection of High or Low screen brightness.

Settings – Test and Diagnostics (Engineer Utility)

These are a series of utilities for checking the health of the oven. They are not needed on a day-to-day basis but are used to diagnose and test the various components within the oven.
A technical manual is available to qualified service technicians.

Element test

This indicates the status of the elements and thermocouples, a tick means they are working correctly a cross indicates a potential issue.

• Touch to retest the components and refresh the indicators.
• Touch to return to the previous menu

Motor test

This screen allows the three different motors to be tested.

• Press to start a motor
• Press to stop a motor

The Oven fan and Case cooling fan motors are speed-controlled and pressing the numbers alllows the speed to be varied. This can be both felt and heard as the speed is increased and decreased.

Microwave test

This screen is used by service engineers to verify the performance of the magnetron componentry
The AC Supply range is used to set the magnetron supply. Over 225V ac is high and under 225V is low.
Temperatures

This screen is used by service engineers to check the temperatures of the various components in the oven. If the temperature is too high it is colored red and may be due to a lack of airflow in the oven.

Energy and Datalog

• This shows both energy consumption and also counts the number of door operations.

• To use it the time and date need to be set in the Datalog setup screen.

• Touch the relevant parameter and use the slider to adjust. Once correct confirm with the save button

Settings – Pin Settings
PIN settings allow selective ownership over the settings and functions of the oven.

To set a PIN touch the cross

Enter a 4-digit PIN and then confirm the number when prompted. Once set the PIN will be needed each time the settings screens are entered. You can disable the PIN by entering the PIN settings screen selecting no PIN and confirming by entering the PIN. A master PIN is available for the Lincat Service desk should the PIN ever be forgotten or lost.

Software and Data

From the Software and Data screens, you can access and update the versions of software and hardware you are using, upload and download recipes including those from another CiBO+, set your preferred screen appearance and set the appropriate language.

Firmware control

• Display Firmware Version ± shows the current version of the Display Firmware Control Firmware Version ± shows the current version of the Control Firmware Hardware Revision ± shows the installed hardware Revision VFD Firmware Version ± Shows the current VFD Version.
• Updates will be issued by Lincat when there is an enhancement to be made to the oven.
• The general sequence is to always update the display hardware first.
• Update Display Firmware ± Ensure the USB stick is inserted into the port behind the lower air grill. Touch the arrow. This takes you to a confirmation screen, touch to confirm and select the version of the software. This will then install and restart the oven. Remove the
• USB stick, fit the dust cap, and replace the grill Update Control Firmware – Ensure the USB stick is inserted into the port behind the lower air grill. Touch the Arrow. This takes you to a confirmation screen, touch to confirm and select the version of the software. This will then install and restart the oven. Remove the USB stick, fit the dust cap, and replace the grill.
• When updating software avoid opening or closing the door as this may create interference that slows the update process.

Recipe Control

• This function provides the facility to upload, download, and delete recipes which allows recipes to be moved between different CiBO+ ovens.
• Import recipe ± Ensure the USB stick is inserted into the port behind the lower air grill. Touch the Arrow. The recipes will then be installed. Remove the USB stick, fit the dust cap, and replace the grill.
• Export recipes ± Ensure the USB stick is inserted into the port behind the lower air grill. Touch the Arrow. These recipes will then be exported to the USB stick. Remove the USB stick, fit the dust cap, and replace the grill.
• Restore default recipes ± restores the as supplied recipes.

Software and Data – Images and Themes

This is where you can load updated recipe icons and set your preferred screen appearance.

• Load Recipe Icons ± Ensure the USB connection is made. Touch the Right arrow to import the recipe icon set. Remove the USB stick, fit the dust cap, and replace the grill.
• Load Theme ± Ensure the USB connection is made. Touch the Right arrow to load the latest theme. Remove the USB stick, fit the dust cap, and replace the grill.

Software and Data – Set Languages
This screen enables you to set the language that the screen text will appear in.
Touch the Right arrow on the language you wish to use and accept by touching the tick.

Error Messages

If you see this warning triangle it indicates an error within the oven. Touch the triangle and it will take you to the diagnostics screen. If  VDQelement or thermocouple error you can re-run the test to confirm. Try re-starting the oven by powering off for 10 seconds at the plug and then restarting it. It the fault persists call Lincat Service.

Safety Cut-out

This appliance is fitted with a safety thermostat, which will cut power to the appliance under fault conditions. If the display works when switching on but the appliance does not heat up, the safety thermostat may need re-setting. Push the red button on the rear panel (Fig 3 G). This re-set cannot be activated until the appliance is cool. If this continues to happen please call our service department.

Warranty Conditions

<RXUSURGXFWKDVDPDQXIDFWXUHU¶VZDUUDQW\7KLVUHTXLUHV\RXWRPDLQWDLQDQGFDUH for your product following the maintenance and cleaning instructions. Only clean using CiBO Sparkle (OC01) ± other products may damage components and result in a non-warranty service call. Always apply oven guard after cleaning. (OS01) If you fail to maintain your oven or damage components during cleaning Lincat may charge you for a warranty repair. Please check the website for terms and conditions.

Cleaning Guide

• See separate cleaning guide for detailed cleaning method.
• Wear protective clothing.
• Do not use a water jet or steam cleaner, and do not immerse this appliance.
• The oven should be cleaned regularly with Lincat Sparkle (OC01) oven cleaner and all food deposits removed. When cool clean with warm water and mild detergent, do not use tools or abrasive materials. Dry with a soft cloth and apply Oven Shield (OS01).
• Do not spray the catalytic converter with detergent or caustic oven cleaner.
• Ensure all door seals are kept clean and inspected regularly to avoid microwave leakage.
• Failure to maintain the oven in a clean condition could lead to deterioration of the surface that could adversely affect the life of the appliance and possibly result in a hazardous situation.
• Regularly check the air filter on the front of the oven. It may be cleaned in a dishwasher. Do not use the oven without the filter.

Servicing, Maintenance and Component Replacement

• We recommend that your CiBO+ oven has an annual Service/Inspection.
• All servicing, maintenance and component replacement should be carried out by one of our recommended service engineers.
• The door seal on this oven is considered a consumable part and is not covered by the warranty.
• Lincat advise that the catalytic convertor is checked annually and debris and food particles carefully removed. Do not use any cleaning solutions on it. Damage to the catalytic convertor is not covered by warranty.
• The oven contains a battery for data logging. Lincat also advise that the battery is changed every 5 years by a service engineer. The battery is not covered by warranty.

Service Information
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY

• Do not operate or allow the oven to be operated with the door open.
• Make the following safety checks on all ovens to be serviced before activating the magnetron or other microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3) seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and latches, (5) evidence of dropping or abuse.
• Before turning on microwave power for any service test or inspection within the microwave generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment, integrity, and connection.
• Any defective or misadjusted components in the interlock, monitor, door seal, and microwave generation and transmission systems shall be repaired, replaced, or adjusted by procedures described in this manual before the oven is released to the owner.
• A microwave leakage check to verify compliance with the Federal Performance Standard should be performed on each oven prior to release to the owner.

GUARANTEE

This oven has a 2 year warranty fulfilled by Lincat in the UK or your dealer outside of the UK.
The guarantee is in addition to, and does not diminish your statutory or legal rights.
The guarantee does not cover:

• FFLGHQWDO GDPDJH PLVXVH RU XVH QRW LQ DFFRUGDQFH ZLWK WKH PDQXIDFWXUHU¶V instructions
• Consumable items.
• Damage due to incorrect installation, modification, unauthorised service work or damage due to scale, food debris build-up, etc.
• The door seal on this oven is considered a consumable part and is not covered by the warranty.
• Cleaning due to heavy raw protein cooking or flour ingress.
• The manufacturer disclaims any liability for incidental, or consequential damages.

CONTACT

For help with the installation, maintenance and use of your Lincat equipment, please contact our service department:

• UK: (+44) 1522 875520
• For non-UK customers, please contact your local Lincat dealer
• All service work, other than routine cleaning should be carried out by one of our authorised service agents. We cannot accept responsibility for work carried out by other persons.
• To ensure your service enquiry is handled as efficiently as possible, please tell us:

Brief details of the problem

• Product code
• Type number All available on serial plate
• Serial number

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>