ROSE BELLA SP1897 Phonograph User Manual

June 16, 2024
ROSE BELLA

ROSE BELLA SP1897 Phonograph User Manual

ROSE BELLA SP1897 Phonograph User Manual

SCHEMATIC DIAGRAM OF CONTROL PANEL

ROSE BELLA SP1897 Phonograph User Manual - SCHEMATIC DIAGRAM OF CONTROL
PANEL

  1. Standby
  2. Mute button
  3. Volume +
  4. Volume –
  5. Previous
  6. Next
  7. Bluetooth play
  8. Black glue play
  9. Sound effect
  10. USB/TF play
  11. Radio play
  12. Pause playback
  13. USB interface
  14. Screen
  15. Previous
  16. Pause
  17. Next
  18. Function select
  19. Power switch/volume adjust knob

INTRODUCTION TO FUNCTION

I. Power switch/Volume adjust knob

  1. turn the knob clockwise to connect the mainframe power
  2. After power on, turn the knob to adjust the volume, or adjust the volume by remote controller

II. USB play

  1. After power on, the default mode is USB play
  2. Under other playing mode, press the USB function button of the remote controller and switch to USB play mode
  3. In USB mode, press the sound adjust button for different sound effect

III. Vinyl record play

  1. Press the Function select button, and PHO appears on the screen
  2. Place the vinyl record on the player, select the corresponding rotation speed and put down the tone arm to play the vinyl record
  3. The player will stop after the vinyl record is over

IV. Bluetooth play

  1. Press the Function select button, and BT mode appears on the screen, connecting the PEL bluetooth.
  2. In the bluetooth mode, press the sound adjust button for different sound effect

V. FM play

  1. when using radio, press the function switch button and switch to FM mode

  2. Play/Pause button on the panel or remote controller is for automatic station-selection in FM mode, press it for 3s to start the
    automatic station search; during search, press the ‘Play/Pause’ button to stop the search; select the station upward or downward by the Next/Previous on the remote controller;

  3. Press the ‘Next/Previous’ button for 3s on the remote controller or panel, start the rapid station-selection upward or downward and selection stops for available station.

OPERATION PROCEDURES OF TURNTABLE

  1. Remove the buckle of tone arm
  2. Lift the tone arm by adjusting the lifting arm
  3. Select the play speed
  4. Remove the protection sleeve of stylus
  5. Place the vinyl record
  6. Move the stylus to the edge of the vinyl record
  7. Put down the lifting arm slowly
  8. After using it, please disconnect the power and assemble the protection sleeve of stylus

ROSE BELLA SP1897 Phonograph User Manual - OPERATION PROCEDURES OF
TURNTABLE

When using the gramophone, switching to the state of gramophone, put in the vinyl record, remove the white protective sleeve of the stylus, and move the tonearm to the vinyl record; then, the turntable starts to work, and when the vinyl record is finished, the turntable will stop automatically.

INSTALLATION DIAGRAM OF HORN

ROSE BELLA SP1897 Phonograph User Manual - INSTALLATION DIAGRAM OF
HORN

  1. Take out the bent tube from the packing box, screw out the upper part (with flower) counterclockwise and separate it from the
    bent tube; (Figure 1)

  2. When assembling the large horn, fix the elbow head with the left hand, and rotate the elbow clockwise with the right hand until it is completely consistent: (Figure 2)

  3. Insert the connecting line of the large horn and the connecting line of the mainframe elbow according to the direction, and finally put the large horn on the base of the mainframe elbow. (Figure 3)

All rights reserved
All other marks, products or company names mentioned in this manual are trademarks of their respective companies

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.

RF warming for Portable device: The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals