BOSCH Zamo Digital Laser Measure Instruction Manual

: June 16, 2024
: Bosch

Table of Contents

References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOSCH Zamo Digital Laser Measure Instruction Manual

BOSCH Zamo Digital Laser Measure Instruction Manual

Original instructions

BOSCH Zamo Digital Laser Measure - Overview

BOSCH Zamo Digital Laser Measure - Figure A,B,C

BOSCH Zamo Digital Laser Measure - Figure D,E,F

BOSCH Zamo Digital Laser Measure - Figure G,H,I

BOSCH Zamo Digital Laser Measure - Figure I,J,K

BOSCH Zamo Digital Laser Measure - Figure K.L

Safety instructions

All instructions must be read and observed in order for the measuring tool to function safely. The safeguards integrated into the measuring tool may be compromised if the measuring tool is not used in accordance with these instructions. Never make warning signs on the measuring tool unrecognizable. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE AND INCLUDE THEM WITH THE MEASURING TOOL WHEN TRANSFERRING IT TO A THIRD PARTY.

Do not use the measuring tool in explosive atmospheres which contain flammable liquids, gases or dust. Sparks may be produced inside the measuring tool, which can ignite dust or fumes.
The measuring tool is delivered with a warning sign (marked in the illustration of the measuring tool on the graphics page).
If the text of the laser warning label is not in your national language, stick the provided warning label in your national language over it before operating for the first time.
Do not direct the laser beam at persons or animals and do not stare into the direct or reflected laser beam yourself. You could blind somebody, cause accidents or damage your eyes.
If laser radiation hits your eye, you must close your eyes and immediately turn your head away from the beam.
Do not make any modifications to the laser equipment.
Never leave the measuring tool unattended when switched on, and ensure the measuring tool is switched off after use. Others may be dazzled by the laser beam.
Have the measuring tool serviced only by a qualified specialist using only original replacement parts. This will ensure that the safety of the measuring tool is maintained.
Do not let children use the laser measuring tool un- supervised. They could unintentionally blind themselves or other persons.
Do not use the laser goggles (accessory) as protective goggles. The laser goggles make the laser beam easier to see; they do not protect you against laser radiation.
Do not use the laser goggles (accessory) as sunglasses or while driving. The laser goggles do not provide full UV protection and impair your ability to see colours.
Warning! If operating or adjustment devices other than those specified here are used or other procedures are carried out, this can lead to dangerous exposure to radiation.

Product description and specifications

Intended Use
Digital laser measure

The measuring tool is intended for measuring distances, lengths, heights and clearances, and for calculating areas.
The measuring tool is suitable for measuring indoors.
This product is a consumer laser product in accordance with EN 50689.

Laser line adapter
The laser line adapter is intended to be used in combina-
tion with the Zamo digital laser measure for vertical or ho-
rizontal alignment (e.g. of wall pictures) in interior areas.

Tape adapter
The tape adapter is intended for use in combination with the Zamo digital laser measure for measuring circumferences (e.g. of vases, pipes, etc.) and lengths of freestanding objects (e.g. televisions, shelves, etc.) in interior areas.

Wheel adapter
The wheel adapter is intended for use in combination with the Zamo digital laser measure for measuring distances between two points (e.g. lengths of material) in interior areas.

Product features

The numbering of the product features shown refers to the illustration of the measuring tool on the graphic page.

(1) Measuring button
(2) Display
(3) Battery compartment cover
(4) Locking mechanism of the battery compartment cover
(5) Serial number
(6) Laser warning label
(7) Reception lens
(8) Laser beam output
(9) Cover cap
(10) Release buttons for adapter

Display elements

(a) Battery warning
(b) Temperature warning
(c) Fitted adapter
(d) Laser switched on
(e) Previous measured value
(f) Unit of measurement
(g) Current measured value
(h) Area measurement

Laser line adapter A)

(11) Level for vertical alignment
(12) Level for horizontal alignment

Tape adapter A)

(13) Tape
(14) Contact edge

Wheel adapter a)

(15) Wheel

a) Accessories shown or described are not included with the product as standard.

Technical data

BOSCH Zamo Digital Laser Measure - Technical data

Note on the measuring range : In unfavorable conditions, e.g. with extremely bright interior lighting or a poorly reflecting surface, the measuring range may be reduced.

Note on measuring accuracy: In unfavorable conditions, e.g. with extremely bright interior lighting, a poorly reflecting surface or a room temperature that deviates significantly from 25 °C, the deviation can be a maximum of ± 8 mm at a distance of 20 m. In favorable conditions, a deviation of ± 0.05 mm/m needs to be taken into account.

BOSCH Zamo Digital Laser Measure - Note on measuring
accuracy

BOSCH Zamo Digital Laser Measure - Note on measuring accuracy
2

A) non-conductive pollution only, whereby occasional temporary conductivity caused by condensation is expected
B) depending on surface characteristics and ambient conditions

Digital laser measure

Inserting/changing the batteries

It is recommended that you use alkaline manganese batteries to operate the measuring tool.

Insert the batteries (see figure on page 4). When inserting the batteries, ensure that the polarity is correct according to the illustration on the inside of the battery compartment.

The battery warning (a) is shown on the display when the battery voltage is weakening.

When the battery symbol first appears on the display, measurements can be made for approx. another 15 minutes. When the battery symbol flashes, you have to replace the batteries because measurements are no longer possible.

Always replace all the batteries at the same time. Only use batteries from the same manufacturer and which have the same capacity.

Do not use lithium-ion batteries. This may result in damage to the measuring tool.

Operation

Switching the laser measure on/off

To switch on the measuring tool, briefly press the measuring button (1). When the measuring tool is switched on, the laser beam is switched on. The indicator (d) flashes on the display.
To switch off the measuring tool, hold down the measuring button (1)

Measuring process
A continuous measurement is performed after the measuring tool has been switched on. The current measured value (g) is shown on the bottom line of the display (see figure A). During continuous measurement, the measuring tool can be moved relative to the target and the current measured value (g) will be updated approx. every 0.5 seconds on the bottom line of the display (see figure B).
The indicator (d) flashes on the display.

The rear edge of the measuring tool is the reference level for the measurement (see figure C).
Length measurement

Press the measuring button (1) to stop the measuring process. The laser beam is switched off and the current measured value (g) is displayed.
Press the measuring button (1) again to switch the laser back on and continue measuring. The current measured value (g) is shown on the bottom line of the display, while the previous measured value (e) is displayed above it.

Area measurement

Press the measuring button (1) twice in quick succession to multiply the last two measurements together (see figure D). The indicator (h) appears on the display and the area measurement is shown.
Press the measuring button (1) twice in quick succession again to display the last two measurements.

If no button on the measuring tool is pressed for approx. 5 min, the measuring tool will automatically switch itself off to preserve battery life.

Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself (even from a distance).

Practical advice

General advice
The reception lens (7) and the laser beam output (8) must not be covered during the measuring process.
The measurements are taken at the center of the laser beam, even when the laser is pointed at surfaces diagonally.

Errors – causes and corrective measures

BOSCH Zamo Digital Laser Measure - Errors – causes and corrective
measures

Fitting the Adapter (see figures E, H, J)

Remove the cover cap (9) from the measuring tool.
Attach the adapter to the laser measure so that it clicks into place.
To remove the adapter, press the release buttons (10) and take off the adapter.
Reattach the cover cap to the measuring tool.

Digital laser measure with laser line adapter

Operation

Activating the laser line

Switch on the measuring tool (see “Switching the laser measure on/off”, page 35).
To show the laser line, briefly press the measuring button (1). The indicator flashes on the display.

♦ Do not direct the laser beam at persons or animals and do not stare into the laser beam yourself (even from a distance).

Note : If the measuring tool is switched on when fitting the adapter, the laser will automatically switch off. Pressing the measuring button (1) will reactivate the laser line.

Aligning the laser line

Align the laser line with the level for horizontal alignment (12) (see figure F) or the level for vertical alignment (11) (rotate the measuring tool by 90°) (see figure G).
The bubble must be in the center of the level vial.
To precisely align the laser line, you can turn the adapter head by ±10° around the laser line.

Note : Make sure that the measuring tool is always positioned horizontally in order to obtain an exact measurement. You can adjust the height of the laser line by placing suitable objects underneath (e.g. a ladder, books, etc.).

Digital laser measure with tape adapter

Operation

Switch on the measuring tool (see “Switching the laser measure on/off”, page 35).

♦ Only use the tape adapter on clean and dust-free surfaces to avoid measurement inaccuracies.

Measuring length (see figures I1−I2)
After the measuring tool has been switched on, the tape extension is measured continuously. The current measured value (g) is shown on the bottom line of the display.
During continuous measurement, the length of the tape can be adjusted, and the current measured value (g) is updated on the bottom line of the display.
The measuring process is indicated by a rolling arrow on the display.

Pull the tape (13) out of the adapter by the contact edge (14) and place the tape against the object to be measured. The visible length of tape (between the two red markings) corresponds to the measurement length (in cm).
Press the measuring button (1) to save the measured value. The current measured value (g) is shown on the bottom line of the display.

Press the measuring button (1) again to start a new measurement. The current measured value (g) is shown on the bottom line of the display, while the previous measured value (e) is saved and shown on the top line of the display.

Note : When switching off the measuring tool, the current measured value (g) is reset to “0”, even if the tape is still pulled out. To avoid measuring errors, always retract the tape fully before taking a new measurement. Do not press the measuring button until you have done this. If the tape is already extended when you are fitting the ad- apter to the measuring tool or switching on the measuring
tool, the “roll in” indicator will appear on the display. Retract the tape fully and press the measuring button before taking a new measurement.

Always make sure that the measuring tape does not snap back into the adapter. Release the tape slowly back into the adapter; otherwise it may become damaged.

Area measurement

Press the measuring button (1) twice in quick succession to multiply the last two measurements together.
The indicator (h) appears on the display and the area measurement is shown.

Digital laser measure with wheel adapter

Operation

Switch on the measuring tool (see “Switching the laser measure on/off”, page 35).

Length measurement (see figures K1−K2).

Run the wheel (15) along the distance to be measured. After the measuring tool has been switched on, the wheel measures continuously. The current measured value (g) is shown on the bottom line of the display. During continuous measurement, the wheel can be moved forwards or backwards. The measured values will be positive in both directions. If the direction is changed during the measurement, the value will be deducted until the starting point (zero point) has been reached. Once the starting point has been crossed, the value will become positive again.
The current measured value (g) is updated on the bottom line of the display.
– The measuring process ends once the wheel has come to a stop. The current measured value (g) is shown.
– Press the measuring button (1) again to save the measured value, and continue measuring. The current measured value (g) is shown on the bottom line of the display, while the previous measured value (e) is displayed above it.

Note : In order to obtain an exact measurement, do not change the angle between the measuring tool and the surface (see figure L). Make sure that you apply a steady amount of pressure throughout the measuring process.
The result may vary on soft substrates and/or when applying excessive pressure. The recommended pressure for an exact measurement result is equivalent to 500 g.

Area measurement

Press the measuring button (1) twice in quick succession to multiply the last two measurements together.
The indicator (h) appears on the display and the area measurement is shown.

Maintenance and Service

Maintenance and cleaning

Keep the measuring tool clean at all times.
Never immerse the measuring tool in water or other liquids.
Wipe off any dirt using a damp, soft cloth. Do not use any detergents or solvents.
Take particular care of the reception lens (7), which must be handled with the same level of care you would give to a pair of glasses or a camera lens.
Send in the measuring tool if it requires repair.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare parts. You can find explosion drawings and information on spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com

You can find further service addresses at:
www.bosch-pt.com/serviceaddresses

Disposal
Measuring tools, accessories and packaging should be recycled in an environmentally friendly manner.

Do not dispose of measuring tools or batteries with household waste.

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, measuring tools that are no longer usable, and, according to the Directive 2006/66/EC, defective or drained batteries must be collected separately and disposed of in an environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended) and the Waste Batteries and Accumulators Regulations 2009 (SI 2009/890) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

Bosch Power Tools

1 609 92A 8MK | (01.03.2023)

Robert Bosch Power Tools GmbH
70538 Stuttgart
GERMANY
www.bosch-pt.com
1 609 92A 8MK (2023.03) O / 527