Voya S1 Helmet Bluetooth Kit User Manual

Voya S1 Helmet Bluetooth Kit

A diagram shows a Bluetooth kit with cables and a control unit with buttons.

Product Introduction

• The control unit has a Power Button (ON/OFF), a Next Song/Volume “+” button on one side, and a Previous Song/Volume “-” button on the opposite side.
• It also features a Microphone Connector, Speaker Connector, LED Indicator, and a Type C charging port.

Package Contents

• BT Kit
• BT Kit Holder
• Hard Rod Microphone Positioning Buckle
• Hard Rod Microphone
• Soft Wire Microphone
• Speakers (2 pieces)
• Hard Rod Microphone Velcro
• Soft Wire Microphone Velcro
• Speakers Velcro (2 pieces)
• Hard Rod Microphone Positioning Buckle Velcro
• USB to Type C Charging Cable

Specifications

Warning: Do not place the device in an environment where the temperature is too high or too low (above 60 °C/below -20 °C).
Do not throw the battery into fire or short-circuit it directly. Do not disassemble or replace the battery yourself.

Operation Guide

1. Bluetooth Pairing: Long press the power button for 5 seconds to turn on the kit and start pairing.
2. Turning On/Off: Long press the power button for 5 seconds.
3. Reset Long press the power button for 10 seconds to reset the kit.
4. Volume Adjustment: Short press the volume buttons to increase or decrease volume.
5. Charging: The LED indicator shows the charging status.
6. Receiving Calls: Press the power button once to answer or hang up calls.
7. Voice Assistant Activation: Double press the power button to activate “Siri” or “Google Assistant”.
8. Music Control: Pause, play, or skip songs with short presses or double presses on the control buttons.
9. Noise Cancelling Mode Switching: Press and hold both volume buttons for 10 seconds to switch modes.

Installation Instructions

1. Assemble the Bluetooth kit onto the helmet by attaching the bracket with adhesive and then securing the device.
2. Install the speakers and microphones inside the helmet using Velcro patches.

Microphone & Speaker Installation

Instructions are provided for installing the speakers and microphones for different helmet types, ensuring proper alignment and secure attachment.

FAQ

How do I pair my device with the Bluetooth kit?

• Long press the power button for 5 seconds until the LED indicator flashes alternately in red and blue, then select the device in your Bluetooth settings.

How can I check if my kit is fully charged?

• The LED indicator will turn off when the kit is fully charged.

Can I use voice commands with this kit?

• Yes, double press the power button to activate “Siri” or “Google Assistant”.

Is the Bluetooth kit waterproof?

• Yes, the kit has a waterproof level of IP66.

FCC Warning

This device complies with part 15 of the FCC Rules and should not cause harmful interference. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device.
If the equipment does cause harmful interference to radio or television reception, the user is encouraged to try to correct the interference by consulting a professional or increasing the distance between the equipment and the receiver.
The device has been evaluated to meet general RF exposure requirements and can be used in portable exposure conditions without restriction.

Product Introduction

WHAT’S IN THE BOX

Basic Function

Bluetooth Pairing

First-time bluetooth pairing: Long press on the power button for 5S to turn on the BT kit, then you will hear the prompt sound “Please pair the Bluetooth”, the indicator light flashes alternately in red and blue.
Open your mobile phone bluetooth and search for the BT device Device pairing name is “St”, choose Sl and you will hear the prompt sound” Bluetooth pairing successful”, blue tooth pairing is successful, and the indicator light is blue.
Bluetooth kits that have already been paired will automatically connect to the last paired device after powering on.

Notes: When the battery level is lower than 20%, the prompt is: “Low battery, please charge The indicator light is red and slowly flashes, reminding every 5 minutes until the power is turned off and the charging is started.

Product Parameters

• Bluetooth Name: S1
• Bluetooth Version: ВТ 5.3
• Speaker: 320 50mW
• Microphone: 6050 -34DB
• Battery: 3.7V
• Product Material: ABS
• Charging Input: 5V 0.5C
• Full Charging Time: Around 1.5hours
• Continue Phone Calling: 12H
• Waterproof   Level: IP66
• Continue Music Playing Time: 24H-28H
• Warning: Do not place the device in an environment where the temperature is too high or too low (above 60 ° C/below -20 ° C); Do not throw the battery into fire or short-circuit it directly. Do not disassemble or replace the battery yourself

Button Function

Notes: When a call comes in, the headset plays the ringtone.

Noise Cancelling Mode Switching

(Different professional noise canceling mode for 3/4 helmet or full face helmet)

How to assemble the Bluetooth Kit?

• Tear off the adhesive release paper on the back of the BT kit bracket and stick the bracket to the selected position on the safety helmet.
• Install the BT kit onto the bracket.

Microphon&Speaker Installation

Speaker Installation

• Tear off the Velcro adhesive release paper from the speaker and apply the Velero to the speaker holes on both sides of the helmet.
• Stick the speaker onto the velcro.
• When installing speakers and microphones, it is necessary to correctly connect the speakers and microphones according to the white triangle docking mark on the connectors.

Microphone Installation: 3/4 Helmet, Open face helmet

• Open the helmet’s left side lining and attach the hard rod microphone Velcro to the inside of the helmet.
• Attach the hard rod microphone to the velcro.
• Adjust the proper distance between the microphone and the mouth and finish the microphone installation.

Microphone Installation: Full-face helmet

• Select the proper position next to the mouth inside the helmet and attach the soft wire microphone Velcro.
• Attach the soft wire microphone to the velcro.
• Finish Installation

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by timing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>