nVent 12PSF Push In Conduit Clamp With Shot Fire Bracket 3 4 Inch Emt Owner’s Manual

nVent 12PSF Push In Conduit Clamp With Shot Fire Bracket 3 4 Inch Emt

Product Information

Specifications

• Catalog Number: 12PSF

Warning

nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.

Contact Information

• Europe Netherlands: +31 800-0200135
• France: +33 800 901 793
• Germany: 800 1890272
• Other Countries: +31 13 5835404
• APAC Shanghai: + 86 21 2412 1618/19
• Sydney: +61 2 9751 8500

Brands

• Our powerful portfolio of brands:
• nVent.com
• CADDY
• ERICO
• HOFFMAN
• RAYCHEM
• SCHROFF
• TRACER

Disclaimer

• All trademarks and registered trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.

Product Usage Instructions

Installation

1. Refer to the product instruction sheets and training materials provided by nVent.
2. Ensure you have all the necessary tools and equipment for installation.
3. Follow the step-by-step instructions carefully to ensure proper installation.
4. If you have any questions or concerns, contact nVent customer service representative.

Usage

1. Familiarize yourself with the product attributes and additional product details mentioned in the user manual.
2. Ensure you understand the diagrams provided to have a clear understanding of the product.
3. Always follow nVent’s instructions and warnings to prevent product malfunction, property damage, or bodily injury.
4. If you experience any issues or notice any abnormalities while using the product, stop using it immediately and contact nVent customer service.

Maintenance

1. Regularly inspect the product for any signs of wear and tear or damage.
2. Clean the product as recommended in the user manual to maintain its performance.
3. Follow any specific maintenance instructions provided by nVent for your product.

Troubleshooting

• If you encounter any problems with the product, refer to the troubleshooting section in the user manual.
• If the issue persists, contact nVent customer service for assistance.

Disposal

• Dispose of the product according to local regulations and guidelines.
• Do not dispose of it with regular household waste.

Warranty

• Refer to the warranty information provided by nVent for details on the coverage and terms of your product warranty.

Frequently Asked Questions (FAQ)

• Q: Where can I find the product instruction sheets and training materials?
• A: The product instruction sheets and training materials are available at www.nvent.com or you can contact your nVent customer service representative.
• Q: What should I do if I notice any abnormalities while using the product?
• A: If you notice any abnormalities or experience any issues while using the product, stop using it immediately and contact nVent customer service for assistance.
• Q: How often should I inspect the product for wear and tear?
• A: It is recommended to regularly inspect the product for any signs of wear and tear or damage. The frequency of inspection may vary depending on the usage and environmental conditions.
• Q: How should I dispose of the product?
• A: Dispose of the product according to local regulations and guidelines. Do not dispose of it with regular household waste.
• Q: What is the warranty coverage for this product?
• A: For details on the warranty coverage and terms, refer to the warranty information provided by nVent.

CATALOG NUMBER

• 12PSF

FEATURES

• Push-in installation of conduit
• Eliminates the need for offset bending conduit
• Complete with shot-fire bracket and pre-assembled drive pin from DEWALT®
• Quickly and easily attaches to concrete, steel or composite metal decking
• Integrated pin installs easily using powder-actuated or single-shot gas-actuated tools
• ICC-ES ESR-2024 evaluation report available for drive pin from DEWALT®

PRODUCT ATTRIBUTES

• Material: Steel; Spring Steel
• Finish: Electrogalvanized;nVent CADDY Armour
• EMT Conduit Size: 3/4″
• Outer Diameter: 0.866″ – 1.181″
• Height: 1 11/16″
• Width: 3 1/16″
• A: 1.300″
• Ultimate Static Load: 15 lb

ADDITIONAL PRODUCT DETAILS

• Uses Powers Fasteners, Inc. part number 50032.
• Static load was established based on a 1” (25.4 mm) embedment depth and 3,000 psi (20.68 MPa) lightweight concrete. For variations in embedment and material please consult anchors.dewalt.com.
• Pre-assembled drive pin from Powers Fasteners, Inc. works with Powers® C4CZ, Simpson® GCN-MEPKT, SPIT® P1000, P200,
• P2201, P3500 / PA3500, P35s, P45, P60, P7201, Sniper; Ramset® 721, Cobra, D45 / D60 / D60L, M70, SA270, T3SS, TS750P,
• TS60P, Viper; Hilti® DX35, DX350 / DX351 / DX36M, DX100 / DX200, DX460, DXA40, DXA41, DXE72 / DX400; Würth® Diva-1,
• BST-1, BST-2 or equivalent nailers.

DIAGRAMS

WARNING
nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury and death and/or void your warranty.

CONTACT

North America

• +1.800.753.9221
• Option 1 – Customer Care
• Option 2 – Technical Support

Europe

• Netherlands:
• +31 800-0200135
• France:
• +33 800 901 793

Europe

• Germany:
• 800 1890272
• Other Countries:
• +31 13 5835404

APAC

• Shanghai:
• + 86 21 2412 1618/19
• Sydney:
• +61 2 9751 8500

nVent.com CADDY ERICO HOFFMAN RAYCHEM SCHROFF TRACER

© 2023 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without notice.

References

• Anchoring and Fastening Systems from DEWALT Anchors & Fasteners
• Building a more Sustainable and Electrified World | nVent
• Building a more Sustainable and Electrified World | nVent

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>