nVent CRLJ37E G Caddy Rod Lock Bar Joist Hanger Owner’s Manual
- June 16, 2024
- nVent
Table of Contents
nVent CRLJ37E G Caddy Rod Lock Bar Joist Hanger
Specifications
- Catalog Number: CRLJ37E G
- Material: Steel
- Finish: Electrogalvanized
- Static Load Safety Factor: 3.5:1
- Rod Size (RS): 3/8
- Width (W): 3.700
- Height (H): 7.400
- A: 1/4
- Wrench Size 1: 9/16 (hex nut size used to tighten to bar joist)
- Wrench Size 2: 15/16 (nVent CADDY Rod Lock hex nut size)
- Static Load (F): 1,000 lb
Product Usage Instructions
Installation
- Ensure that you have read and understood the product instruction sheets available at www.nvent.com or from your nVent customer service representative.
- Select a suitable location on the bar joist for installation.
- Place the nVent CADDY Rod Lock Bar Joist Hanger onto the bar joist, aligning the holes with the desired position.
- Insert the appropriate rod size (RS) through the holes of the hanger.
- Use a wrench with a size of 9/16 to tighten the hex nut on the hanger, ensuring a secure connection to the bar joist.
- Use a wrench with a size of 15/16 to tighten the nVent CADDY Rod Lock hex nut, securing the rod in place.
Warnings: nVent products must be installed and used strictly following the provided instruction sheets and training materials. Failure to do so may result in product malfunction, property damage, serious bodily injury, death, and voiding of warranty.
Additional Product Details
Wrench Size 1 represents the hex nut size used to tighten the hanger to the
bar joist. Wrench Size 2 represents the nVent CADDY Rod Lock hex nut size.
FEATURES
- Easily installs from underneath the bar joist
- Easily installs on the lower or upper truss chord of the bar joist
- A plastic protection cap prevents dirt or structural coatings from obstructing the “push-to-install” mechanism
- Prefabricated assemblies easily lift and lock into place, helping to save time and money
- Easy “push-to-install” design allows installers to simply push the threaded rod through the mounting hole, instantly holding it in position
- Works with slightly damaged threads and minor burrs on the threaded rod
SPECIFICATIONS
Catalog Number
|
Material
|
Finish
| Static Load Safety Factor|
Rod Size(RS)
|
Width(W)
|
Height(H)
|
A
|
Wrench Size 1
|
Wrench Size 2
|
Static Load(F)
---|---|---|---|---|---|---|---|---|---|---
CRLJ37E
G|
Steel
| Electrical vanished|
3.5:1
|
3/8″
|
3.700″
|
7.400″
| 5/8″ – 1
1/4″
|
9/16″
|
15/16″
|
1,000 lb
ADDITIONAL PRODUCT DETAILS
Wrench Size 1 represents the hex nut size used to tighten to bar joist. Wrench Size 2 represents nVent CADDY Rod Lock hex nut size.
DIAGRAMS
WARNING nVent products shall be installed and used only as indicated in nVent’s product instruction sheets and training materials. Instruction sheets are available at www.nvent.com and from your nVent customer service representative. Improper installation, misuse, misapplication, or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property damage, serious bodily injury, and death and/or void your warranty.
FAQ
- Where can I find the product instruction sheets?
- The product instruction sheets are available at www.nvent.com or you can request them from your nVent customer service representative.
- Can I use this product for other applications?
- This product is specifically designed for use as a bar joist hanger and should not be used for other applications.
- What is the maximum static load this product can handle?
- The nVent CADDY Rod Lock Bar Joist Hanger has a static load capacity of 1,000 lb.
- Can I adjust the width and height of the hanger?
- No, the width (W) and height (H) of the hanger are fixed at 3.700 and 7.400 respectively.
CONTACT
North America
- +1.800.753.9221
- Option 1 – Customer Care
- Option 2 – Technical Support
Europe Netherlands:
- +31 800-0200135
France
- +33 800 901 793
Europe Germany
- 800 1890272
- Other Countries:
- +31 13 5835404
APAC Shanghai
- + 86 21 2412 1618/19
Sydney
- +61 2 9751 8500
© 2023 nVent. All nVent marks and logos are owned or licensed by nVent
Services GmbH or its affiliates. All other trademarks are the property of
their respective owners.
nVent reserves the right to change specifications without notice.
References
- Building a more Sustainable and Electrified World | nVent
- Building a more Sustainable and Electrified World | nVent
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>