O3 Pure O3 Eco Laundry System Owner’s Manual

Eco Laundry System
Owner’s Handbook

O3 Eco Laundry System

https://o3pure.com/pages/warranty-registration

O3 PURE OZONE LAUNDRY SYSTEM FOR USE WITH COLD WATER ONLY.
Installation instructions should be reviewed prior to installation.

Prior to Installation

1. Remove O3 Pure Eco Laundry System (LS) from packaging and inspect for any shipping damage. Keep packaging in the event of return for warranty.
2. Check to ensure you have all components : (Fig. a) (a.1) 1 x O3 Pure LS Unit, (a.2) 1 x Power adapter, (a.3) 2 x Screws and Molly’s, (a.4) 1 x Water hose, (a.5) 1 x Screwdriver, (a.6) O3 Pure LS Quick Install Guide, (a.7) Owners Handbook with Warranty card.
3.  The O3 Pure LS can be attached to any wall near your washing machine. However check to make sure the power adapter will reach the electrical socket and that the water hose will reach from the O3 Pure LS unit to the washing machine. If the hose is not long enough, another longer hose can be used.( Fig. b)

Use & Safety Considerations

➥ Before using, please read the Owners Handbook carefully.
➥ Do not operate the unit with the cover removed.
➥ Disconnect all power before servicing.
➥ Do not use a power adapter other than the one provided with your O3 Pure LS unit.
➥ Maximum water inlet pressure is 100psi.
➥ Leave the existing hot water as originally installed. Change the wash and rinse cycles to cold/cold.
➥ Mount the O3 Pure LS unit horizontally only.
➥ O3 Pure LS is designed for residential use only and is not intended for use in a commercial or industrial setting.

Installation:

1. Place the Quick Install Guide on the wall in the desired location to determine the spacing and placement of the mounting holes on the wall. A carpenters level should be used to insure that the O3 Pure LS is mounted level in the horizontal plane. (Fig. c)
2. Mark the location of the two mounting holes on the wall with a pencil. Drill appropriate sized holes for the screws or mollies in each marked location. Install the screws leaving them protruding from the wall by about 1/4 inch. A set of mounting hardware has been provided. If it is not possible to mount the O3 Pure LS to wall studs, you should use the included “molly” type expandable screw anchors. For any other type of mounting scenario (concrete block, etc.) please consult your local hardware store for assistance.
3. If needed remove the cover from your O3 Pure LS by slightly pressing the tabs on each side of the cover inwards. (Fig. d – d.1) While gently holding the tabs in, lift the cover up 1 inch and then straight out toward you. There is a quick disconnect for the Ozone Level Button. It is located behind the cover and can be used to set the cover down for easier installation.
4. Place the O3 Pure LS against the wall so that the protruding screws slip through the “keyholes” (Fig. e – e.1) in the back of the unit. Slide the unit down into the lock position of the keyholes. You can now tighten the two screws to hold the unit firmly in place. DO NOT over tighten the screws.
5. Turn off the cold water taps/faucet to your washing machine. Place a pail under the cold water hose connection to the washing machine. Disconnect the cold hose from the washing machine placing the end into the pail. Flush cold water line with water by turning the cold water tap on. Check filter (if applicable) at the cold water inlet of washing machine. Clean residue from filter if necessary. Check that the rubber washers in the hoses is in place and connect the cold water hose from the cold water supply to the inlet supply of the O3 Pure LS (Fig. f – f.2). Properly tighten the hose to the inlet fitting, but do not over tighten and do not use thread tape.
6. Using the new hose provided, connect one end of the hose to the water outlet of the O3 Pure LS and the other end of the hose to the cold water inlet of the washing machine (Fig. f – f.1) Properly tighten both ends of the hose, but do not over tighten or use thread tape.
7. Replace the cover on the O3 Pure LS.
8. Plug the power adapter into the DC adapter plug-in on the side of the O3 Pure LS unit (d.2) and then plug the adopter into the wall outlet. (Fig. b)
9. Ensure all hoses are properly installed and tightened, and that the power supply has been securely plugged in. SLOWLY turn the COLD water supply back on and check for any leaks or drips. Gently retighten the fittings and if leaks are apparent, be careful not to over tighten.
10. Set the wash cycle on your washing machine to COLD WATER wash and COLD WATER rinse.

Alarm
Your O3 Pure LS unit is equipped with an internal leak detector. If a leak happens to develop inside of the unit the sensor will set off an audible alarm. This alarm will continue to buzz until the leak is stopped and/or the unit is unplugged. If this alarm should occur, you should unplug the unit, turn off the cold water valve and call us for assistance.

Ozone Selection Level Button
By pressing the Ozone Level Button, you are able to select the ozone output of the unit and choose between 3 settings. You can select the output while the unit is running or while the unit is off. The unit will remember your selection unless there is a power outage in which case the unit will default to the Green ozone setting. The setting descriptions below are meant as a starter guide. Feel free to experiment and see what settings work best in your home.
No Light: Allows the unit to run without engaging the ozone generator. The Photo Catalytic Oxidizer (Fig. h – 7) will still operate and provide a very mild cleaning action. Green Light: This setting is usually recommended for general washing and everyday use.
Blue Light: The unit will run at full ozone output. (g.1) For whites and deep cleaning colors.
Note: The unit may briefly flash red at beginning of some fill/rinse cycles. This is usually normal as the unit rebuilds pressure. In some instances it may also indicate a partially clogged filter located just inside the water intake in some washing machines.

Using Your O3 Pure LS

The use of your O3 Pure LS unit is very easy and convenient. As long as you install your O3 Pure LS properly, you simply operate your washer according to the instructions provided by the manufacturer. O3 Pure LS is designed to automatically turn on as soon as the washer demands water for the wash cycle and again for any rinse cycles. The only differences are that you ONLY USE THE COLD WATER setting for both the wash and rinse cycles on your washer.
Keep in mind that the fibers in your clothes are most likely saturated with residual detergent. It may take up to 5 washes to remove this residue. During this initial phase your laundry water may sud and clothes especially heavier items like bath towels may come out stiff and crusty. This is normal as the Ozone breaks down that embedded detergent. After this initial process, your laundry will begin to be odor free and soften up. Also it can take up to 15 washes to remove old detergent residue from your washer itself. If you have water with very heavy mineralization and/or iron content, we recommend installing a prefilter directly before the O3 Pure LS. This will extend the operation life of your new O3 Pure LS unit and enhance it’s cleaning power.

Note: Do not run hot water through your O3 Pure LS.
Stains

We suggest that you pretreat stains, just as you would without an O3 Pure LS unit. For normal soiled laundry, you should only need a small amount of detergent or none at all.

How to tell your O3 Pure LS unit is working?

You can easily tell if your O3 Pure LS unit is operating properly by looking through the viewing window. The viewing window will glow blue or green (when selected using the Ozone Selection Button). When the water stops flowing, the O3 Pure LS will automatically turn off following a short cool-down period.

Model Selection
Our new generation O3 Pure LS units now work with all washers, Front and Top Load, High Efficiency and Standard. No separate units are necessary.

Advantages of O3 Pure LS
Residential Ozone Laundry Cleaning Performance System 

➥ Reduces Energy Use: Reduced wash cycle times, reduced need for rinse cycles, cold water wash (not paying for heating water).
➥ Reduced Water Use: Ozone wash systems require fewer rinse steps reducing water consumption.
➥ Reduced Chemical Use: Ozone washing systems use little or no detergent.
➥ Reduction or Elimination of Odors: Your O3 PURE LS will combat those musty smells in both your clothes and your washer.
➥ Improves Textile Life and Quality: Shorter wash cycle times, the use of cold water and  fewer rinse cycle’s means less wear and tear on fabrics. Fabric life and color quality isalso increased due to reduced exposure to chemicals.
➥ Reduces damages to environment: Less chemical use equals less environmental damage in our water ecosystems.

O3 Pure LS Technical Specifications

INTERNAL DIAGRAM (Fig.h)

In case there is an issue with your O3 Pure LS please contact customer service. The diagram below will be a resource in locating the part(s) of the unit as the customer service representative guides you through troubleshooting and servicing your unit.

1. Water Inlet
2. Water Outlet
3. Flow Switch
4.  Pipe Assembly
5.  Venturi with Check Valve
6. Static Mixer
7. PCO Cell
8. Control Module
9. Oxidizing Module
10. Check Valves

O3 Pure LS Limited Warranty

Your O3 Pure LS is warranted to be free from all defects in material and workmanship in normal household non-commercial use for a period of (3) years limited from date of purchase from either and authorized sales agent or the directly from O3 Pure. The warranty is granted only to the original purchaser and members of his or her immediate household. Please retain your sales receipt. The warranty is subject to the following provisions: Any damages or malfunctions caused by negligence, abuse, or use not in accordance with the Owner’s Use Handbook are not covered by this warranty. Likewise, any defects or damages caused by unauthorized service or the use of other than O3 Pure LS parts are not covered. O3 Pure will, as its option, repair or replace a defective O3 Pure LS or part(s) for the O3 Pure LS that is covered by this warranty. As a matter of warranty policy, O3 Pure will not refund the customer’s purchase price.

What is not covered by the Limited Warranty?
THIS WARRANTY DOES NOT COVER CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND DOES NOT COVER INCIDENTAL COSTS AND EXPENSES RESULTING FROM ANY BREACH OF THIS WARRANTY, EVEN IF FORESEEABLE. Some States or Provinces do not allow the exclusion or limitations of incidental or consequential damages, so the above limitation or exclusion may not apply to you depending on the State or Province of purchase. This warranty will not cover  3 Pure units sold, shipped or used outside of the U.S. and its Provinces.
Nor does this warranty cover damages caused by the services performed by anyone other than O3 Pure or it authorized service providers, use of parts other than genuine O3 Pure LS parts or external causes such as abuse, misuse, inappropriate power supplies or acts of God.

Other Limitations

THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY EXPRESS WARRANTY, WHETHER WRITTEN OR ORAL. IN ADDITION O3 PURE HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES WITH RESPECT TO YOUR O3 PURE LS, INCLUDING MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. Some States or Provinces do not allow disclaimers of such implied warranties or limitations on how long an implied warranty lasts, so the above limitation may not apply to you depending on the State or Province of purchase.

How do you obtain warranty service?

O3 Pure products are high quality appliances and with proper care are intended to provide years of satisfying performance. However should the need arise for warranty or servicing, simply visit our website, email us or call O3 Pure Customer Service. Please do not return your O3 Pure LS unit for servicing without first speaking to an O3 Pure Customer Service representative.

Contact North America:

Pure Energy LLC
O3PURE Division
8100A Main Street
Garrettsville, OH 44231| Please contact us without hesitation if you need help:
Website: www.o3pure.com
Sales / Service line: 330-527-9057
---|---

Warranty Activation Options: complete warranty activation at www.o3pure.com or complete warranty card place in envelope and send to Pure Energy LLC address above.

Warranty Card

Name:

Street Address:
City, State/Province, Country, Zip Code:
Email Address:
Phone Number:| Date Purchased:
Model Number:| Serial Number:

www.o3pure.com

References

• O3 PURE
• Warranty Registration – O3 PURE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>