ZKYMZL B08596SWSP Mini LED Spider Moving Head Light User Manual

ZKYMZL B08596SWSP Mini LED Spider Moving Head Light

User Manual
Please read the instructions carefully before use

Thank you for choosing our company’s products. In order to use the device safely and quickly, please read the user manual carefully before using the device and install or use the device in strict accordance with the requirements of the user manual. If you have any questions during the use, please feel free to contact us or the dealer; at the same time, you are welcome to provide valuable advice on our products, we will be happy to provide you with quality consulting and after-sales service.

Attachments

1. LED mini moving head spider light: 1PCS
2. Power cord: 1PCS
3. User Guide: 1PCS
4. Screw: 2PCS
5. Bracket: 1PCS

Notice

1. Before using the device, please unpack and double check for shipping damage.
2. Customers should carefully read the User Manual before using impend and operate the equipment in strict accordance with the requirements of the User Manual. Any damage to the equipment caused by failure to follow the User Manual and human error is not covered by the warranty.
3. This unit can only be used indoors and in dry places. The maximum ambient temperature should not exceed 40 °C.
4. When installing the equipment, it must be carried out by professional operators. The place where the equipment is placed must be well ventilated. The wall should be no less than 50 cm away from the surface of the equipment.
5. Before turning on the device, make sure that the device’s power supply voltage and frequency meet the device’s power requirements.
6. Before starting the device, check the integrity of the power cord to ensure the surrounding environment is safe. Do not touch any wires during operation, otherwise there is a danger of electric shock.
7. Avoid any flammable liquids, water or metal objects entering the equipment. If this happens, turn off the power immediately.
8. Do not use the device in a dirty or dusty environment, and pay attention to cleaning the device regularly.
9. If the fuse of the device needs to be replaced when it burns out, the same type of fuse must be used after the power is turned off, and replaced by a professional technician.
10. Do not open the device for repair, otherwise the equipment will be damaged or malfunction and will not be covered by the warranty.
11. If the device is not used for a long time, disconnect the device from the power source.
12. When the equipment needs to be transported again, please pack the equipment with the original packaging materials.
13. When the light is on, do not look directly at the LED light.

Technical Specification

1. Working voltage (frequency): AC100~240V (50HZ / 60HZ)
2. Working mode: automatic, voice control, DMX512, master-slave
3. Light source: high brightness LED
4. Color: RGBW mixed and multiple colors
5. Beam angle: 3°
6. Scanning angle: Y1 / Y2: 120°/ 120°
7. Strobe/dimmer: linear dimming
8. Electronic dimming: 0-100%
9. Control channel: CH10 / CH14
10. Size: length width height = 290 210 230mm;
11. Weight: 2.4Kg

Front Panel

1. Menu: Menu selection button
2. Up: scroll through the menu buttons
3. DOMN: scroll through the menu buttons
4. ENTER: Save menu button

Menu function setting and description：

enter the setting page, when the display flashes “dXXX”, press the “UP” or “DOWN” key to set the desired address code, and then press the “ENTER” key save
Chnd| Channel selection menu: The device has two channel modes: 10Ch and 14Ch, press “ENTER” to enter, the display flashes to show the current channel mode, press “UP” or “DOWN” to set 10Ch or 14Ch, then press “ENTER” Save .
SLnd| Auto mode or slave mode setting menu: “∩ASt” is automatic mode, “SL 1” and “SL 2” are slave modes, press “ENTER” to enter, the display flashes to show the current working mode, press “UP” Or “DOWN” key to select the mode setting, it is recommended to set to “∩ASt” mode normally, and then press “ENTER” to save.
---|---
Shnd| Projection mode setting menu: The device has 16 projection modes, Sh 0~Sh 15, respectively, press “ENTER” to enter, press “UP” or “Down” to select, and then press “ENTER” to save, usually set to “S h 0”.
Auto| Auto mode menu setting: press “ENTER” to enter, press “UP” or “DOWN” to select “oFF” or “on” mode, “oFF” is the mode of automatic slow operation and voice-activated intelligent conversion, “on” is automatic Mode and press “ENTER” to save the settings
SoUn| Voice control mode menu setting: press “ENTER” to enter, press “UP” or “DOWN” to select “on” or “oFF”, “on” voice control is on, “oFF” voice control is off, and then press “ENTER” to save , Set to “on” status normally
SenS| Voice control sensitivity setting menu: press “ENTER” to access, press “UP” and “DOWN” keys to set the value of voice control sensitivity, usually 50~60, and then press “ENTER” to save.
PInt| Device rotation projection direction menu setting: press “ENTER” to input, press “UP” or “DOWN” to select “No” or “yes”, “no” means that the two projection axes rotate relative to each other, and “Yes” means that the two projection axes Rotate in the same direction, and then press “ENTER” to save
tInt| Device rotation projection direction menu setting: press “ENTER” to input, press “UP” or “DOWN” to select “No” or “yes”, “no” means that the two projection axes rotate relative to each other, and “Yes” means that the two projection axes Rotate in the same direction, and then press “ENTER” to save
Led| Display mode menu setting: press “ENTER” to enter, press “UP” or “DOWN” to select “On” or “oFF”, “on” means that the display is always on, “oFF” means that the display is turned off within 1~2 minutes Display, then press “ENTER” to save the settings.
disp| Font forward display and reverse display menu settings: “dISP” means
| forward display, “dSIP” means reverse display, press “ENTER” key to set, release “ENTER” key after setting, ten seconds later, the display Display the set font direction.
---|---
test| Auto test: please User no set it
rSet| Device reset menu: Press the “ENTER” key to reset the device.

Online control mode

1. Use DMX512 standard controller to control equipment
   According to the figure below, use the signal cable to connect the device and DMX512 controller, and then connect the power of all devices. After turning on the power, you can control the projection effect of the device according to the DMX512 channel function description table. (Note: All connected devices must be set to the same channel mode: 14CH or 10CH, otherwise the device will lose synchronization).

2. Master-slave online control
   Connect more than two devices with signal cables. As shown in the figure below, after turning on the power of all devices, the connected device group will automatically generate a host, and you will see that the other devices will work synchronously with the host. (Note: All connected devices must be set to the same channel mode: 14CH or 10CH, otherwise the device will lose synchronization)

DMX512 channel control function description table

fast to slow
CH4| CH4| 000~255| Control light brightness
CH5| CH5| 000~007| Turn off the light
008~015| Turn on the light
016~131| Strobe: the speed of strobe changes from slow to fast
132~139| Turn on the light
140~181| The lamp lights up quickly, then goes out slowly
182~189| Turn on the light
190~231| Light turns on slowly and turns off quickly
232~239| Turn on the light
240~247| Strobe
248~255| Turn on the light
CH6~CH9| CH6~CH9| 000~255| Red →Green→Blue→White Dimmer:0~100%
| CH10~CH13| 000~255| Red →Green→Blue→White Dimmer:0~100%
CH10| CH14| 000~007| No function
008~063| Auto mode
064~127| Sound control
128~255| Reset

Troubleshooting

When the equipment has the following faults, please follow the instructions to troubleshoot:

1. After connecting the power, the device cannot work normally: please check whether the input voltage matches the working voltage required by the device.
2. In the master-slave mode, the slave device does not work, please check the following:
3. Please make sure that in the connected device cluster, only one device displays “Sh 0” on the display, all other slave devices display “SL 1”, and all devices must be set to the same channel mode
4. Check whether the signal line is properly connected.
5. When using the DMX 512 controller to control the device, the device does not work and the DMX signal indicator does not light up, please check the following items:
6. Check whether the DMX512 controller is normal and whether the device settings are normal.
7. Check whether the signal line connection is normal.
8. Turn off the power of the device, then turn on the power again after 3 minutes, and observe whether the device can work normally. If it still does not work, please replace the power cord and try again.
9. The voice control does not respond, please check whether the device settings are correct.
   If the above methods still cannot solve the problem of equipment failure, please contact the nearest dealer or our company’s after-sales service department, we will wholeheartedly provide you with quality after-sales service.

Statement

The product has been strictly inspected before leaving the factory, and its performance is excellent, the accessories are complete and the packaging is intact. Before using this product, users must carefully read and strictly abide by the provisions of the “User Guide”. Otherwise, we will not bear any responsibility for product quality problems caused by ignoring this manual! If you buy our products and encounter quality problems during normal use and need repairs, please contact the nearest dealer or our customer service department. We will serve you wholeheartedly.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>