able ACF-AVENS42-5BL AVENS Series Fan User Manual

able ACF-AVENS42-5BL AVENS Series Fan User Manual

Demission Instruction

CEILING FAN

NO| PARTS BAHAGIAN Vit| QUANTITY
KUANTITIRI| NO| PARTS BAHAGIAN V*| QUANTITY
KUANTITIgat
---|---|---|---|---|---
1| TOP CANOPY / SENGKUAP ATAS I :I; IS.| X1| 7| LED I )ti| X1
2| HANGING TUBE C/W RUBBER WHEEL ROD BESI / /1; It| X1| 8| LAMP COVER / PENUTUP LAMPU / t.1 T . ( FOR LIGHT MODEL)| x1
3| COUPLING COVER / SENGKUAP BAWAH / 4’ic’ :).:■i| X1| 9| TRANSMITTER / ALAT KAWALAN / 11.:04tM| X1
4| FAN MOTOR / MOTOR KIPAS / Ixtti:i ILK| X1| 10| BLADE SCREWS / SKRU BILAH / IiIIII–0.11:r.| X1
5| FAN BLADES! BILAH KIPAS / PAL ti.1111.);| X5| 11| RECEIVER / PENERIMA / Min| X1
6| LED PLATE / PLAT LED / ‘Xi ig. (FOR LIGHT MODEL)| Xi| 12| BALANCING KIT / SET PENGIMBANGAN / ‘Mg| Xlset
FAN SIZE SAIZ KIPAS JAM1–ft| VOLTAGE VOLTANFLEE| MAX FAN POWER KUASA KIPAS MAX RAM t| MAX LIGHT POWER KUASA LAMPU MAXaMicii341| MAX SPEED(RPM)
KELAJUAN MAX| NETT WEIGHT BERAT BERSIHt| GROSS WEIGHT BERAT KASAR
---|---|---|---|---|---|---
56″| 220-240V / 50Hz| 45W| 22W| 220 ± 10%| 8.7KG| 10.3KG
42″| 220-240V / 50Hz| 45W| 22W| 245 ± 10%| 8.2KG| 9.8KG

WARNING

TO ENSURE YOUR PERSONAL SAFETY, PLEASE READ THROUGH THE INSTRUCTION
MANUAL BEFORE OPERATING THE PRODUCT.

1. Do not bend the blade during installation, blades balancing or fan cleaning.
2. To prevent accidents, power switch must be OFF and electrical wiring must be disconnected before ceiling fan installation, dismantling, maintenance or cleaning.
3. Ceiling fan installation and electrical wiring must be done by qualified technician in accordance with all applicable codes and air conditioning engineers (ASHRAE) or the local qualified authorities.
4. Be cautious when drilling the wall to avoid damaging electrical wiring and other hidden parts.
5. Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on plaster ceiling or any types of drywall ceilings. During ceiling fan installation, all screws must be tightened at all allocated parts.

SAFETY GUIDELINES

1. Please do not install the ceiling fan at high humidity areas.
2. Distance between fan blades and ground must be at least 2.5 meter and above.
3. Do not touch the ceiling fan while it is operating.
4. For safety purposes, all electrical connections must conform to the national electrical safety codes and earth wire must be installed correctly (suitable for power supply of 220-240VAC / 50Hz).
5. Do not modify the ceiling fan and only use the parts supplied accordingly.
6. Do not attempt to repair the fan. Always liaise to our authorized service agent if the fan is not functioning well.
7. This appliance is not intended for use by persons (including children) with lack of sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
8. Children should be supervised to ensure that they do not play with the appliance.
9. The ceiling fan electrical wiring must be installed with means for disconnection incorporated in the fixed wiring provided and safety cable must be installed according to the steps in this manual.

INSTALLATION PROCEDURES

STEP 1 (See Diagram 1)

Before installation, remove the rubber wheel from both side of the hanging tube.

STEP 2 (See Diagram 2)

1. Insert the hanging tube through top canopy and coupling cover.
   Masukkan rod

2. Thread the safety cable and lead wire from the fan motor though the hanging tube. Place the lead wire and safety cable out the top of hanging tube.

3. Insert the hanging tube into the motor and aligning holes to the motor coupling.

4. Screw the hanging tube to motor with the previous bolt, washer, nut and R-pin.

DIAGRAM 2

Step 3 (See Diagram3)

1. Remove the bolt at the rubber wheel before installation.
2. Hang the rubber wheel on the U-Hook. (Figure a)

Step 4 (See Diagram4)

1. Lift the motor until the bracket hole of the hanging tube and rubber wheel’s hole are
   aligned.

2. Use bolts to pass through the hanging tube coupling plat and the rubber wheel and tighten
   the bolts, flat washer, spring washer, nut, R-pin that were loosened previously.

Step 5 (Safety Cable Installation)

1. Remove the safety cable screw from the hanging tube coupling plat. (Diagram 1)
2. Amange the safety cable as above diagram 2 shown.
3. Tightenthe safety cable on the hanging tube with screws, (Diagram 3)

WARNING

If the safety cable is not properly secured, it may cause injury if the ceiling fan falls.

STEP 6 (Electrical Wiring Connection)

caution, risk of electric shock

1. Turn off the power supply before installing the ceiling fan.
2. Use the two pieces of “lead wire connector”” from the screw pack and connect them to the fan motor’s wire socket and then connect all 3 wires “Live, Neutral & Earth” to incoming power supply accordingly.
3. Installation should be performed by a qualified electrician, and all wiring connections must be in accordance with local national regulatory wire standards.

STEP 7 (Refer Diagram7)

Raise the top canopy and tighten it with the screw attached.

STEP 8 (Blade Installation)

Insert the blade screws through the flat washerand blade then secure the blade to the motor by tightening the screws.

PRODUCT DIMENSION DIAGRAM

RF TRANSMITTER

Function of Transmitter

fig173Jx1E6INIADJSM
S| | Switch off the ceiling fan
6| | LED Light Function
7| | Sleep Mode (auto reduce and maintain at speed 2 after 1 hour from speed).
8| | Natural Wind Mode (Press this button to switch the fan speed from high to low)
9| IHTimer 3H6H| Upon timer set, fan

Front

Back

Battery cover

**battery

This fan is operated using remote control.**

TROUBLE SHOOTING

SYrrOlcen Gelala we| Possible|
---|---|---
Wobt1m| •| Ensure that 01 SCICIINS somatic the|
lier0050r0| •| DIMS 0110n .|
OIR| •
It Ku nave magpie calks° WS|
| •| If the tan blade h damaged, contact the after soles service center for replacement. If me damage does nal originate from the|
| •| .|
| •| PcalikonSernu0 blots 4)05|
| | |
| •| |
| | |
| •| **|
| | |
| •
•| |
| | AL|
NNW| •| Check 01 initolciticns. It it IS base. lighten It.|
Bert)unvi| •| Strict ‘vivo peastooneon. SeglOrry0 lale001. IselOtkOnny0.|
KR| •| 12W0fietiRie. Del. reit,|
…xts upon stadula| •| his is a normal phenomenon. as the power is passed through a three-phase|
.1,t ce pada perm000n| | Witless GC motor wiMoul affecting performance.|
nolitlilb| •| hi 00010h fenernOn0 Nova ketone ku0S0 Mr Otold mobla motor DC trustless li0O tOSO Woad mOreki0kOn prolog.|
| •| itazva. 1112StelitiBEIGVIIIMitil. T1110121t.|
No argon| •| Moto sup it is not tuning In the “reverse’ accretion|
710000Won °nein| •| lo took Oroh “tartar.|
SWIM| •| OttleSktitett.|
Fennel functioning| •| Make SUM oil wires as connected correctly.|
boos alok borfungsi| •| If the voltage a bker Owl 1400 or exceeds 2700 for more than 5 seconds.|
Xlfieb| | the motor will anomie/No.31M ad on me Dower SUPPIY. When the valor returns to narna it wit turn an COOMOtiCCay.|
| •| |
| •| |
| | |
| | Ouiefra II k.|
| •| tentgaltlif 1400,2111t2700/112619. 1 61/Ititabt/M4119(21r a %EMU|
| | *11. triattfit|
Remote coned not| •| When the remote-control button la pressed. MeLEO indicator billet Miocene|
tunapprig| | that the battery voltage is NO 1010/. please replace the battery .|
Alas pub WI ak| •| Appalls butane /Slob °noon. LED ,|
bartungsi| | banana Omen , sea yang !Ansa.|
ARO aleft11| •| bilt iliglISIII. LEINlifd70111. ligu4ib4als112. eteametit.|
Dudng high speed. the| •| TIMIS normal Of the Meter is not only protected by 0 voltage regulator. it is|
don turning fad and| | and protected by an additional thermal senor where it minima the motor|
Men slow down| | temperature from rang to not more than ?•C. It is to increase the ge span|
dada              keklivon ling?, tCos telaver5) lerh/.| •| of the motor. hi ° blaS0 korona motor baton pen|
| | . to Sego Si, sensor hobo mono to|
a Agin. Ilketlatifilla| |   root WM|
ee| | |
| •| . 61 is ltdITC2,2110E116921In..|
| | DiftablAltiltflittiglifefAIITABI115°C. 6ek/a7 41110 1 044/190/ P.|

IMPORTANT

DO NOT CONNECT THIS CEILING FAN REMOTE CONTROL TO DIMMER SWITCH OR WALL REGULATOR.

Ceiling fan must be hooked on concrete ceiling. Do not install the ceiling fan on plaster ceiling or any types of drywall ceilings. During ceiling fan installation, all screws must be tightened at all allocated parts.

XWRONG INSTALLATION

a) Ceiling Fan must be mounted above 2.5m from the floor 1m from the wall to the blade.
b) Avoid fixing inside a dome ceiling.

C) Avoid Installing on a deep tray ceiling.
d) Avoid Installing on a slanted ceiling.

Our Warranty

10 YEARS Warranty:  FOR FAN MOTOR ONLY
2 YEARS Warranty:  FOR RECEIVER ONLY
1 YEARS Warranty:  FOR ALL PARTS

8 moths Warranty Extension

Online Registration

1. Log on to www.rubine.com.my
2. Click on ‘Support’, followed by ‘Product Warranty Registration’ to proceed. You’re required to sign up as a member.
3.  You’ll receive a notification of warranty registration confirma- tion via email.
4. Please keep your online warranty certificate for reference/future warranty claim.

Customer Care

AFTER-SALES SERVICE

Email: fterm @fiamma.com.my

FIAMMA TRADING SDN BHD 330476-p (A member of Fiamma Holdings Berhad)
2-1, Wisma Fiamma, No.20, Jalan 7A/62A, Bandar Manjalara, 52200 Kuala Lumpur. Tel: 03-6279 894

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>