BRITEC AF-03 Air Heat 3 WIFI Heating Fan Instruction Manual

: June 16, 2024
: BRITEC

Table of Contents

AF-03 Air Heat 3 WIFI Heating Fan
BRITEC
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AF-03 Air Heat 3 WIFI Heating Fan

BRITEC

FAN AND HEATER
2 IN 1

FAN HEATER

AIR HEAT 3 WIFI

INSTRUCTIONS GUIDE

Thank you for choosing this product, please read this instruction manual
before using it.

RECOMMENDATIONS

To assure maximum performance of the device, please note the following
recommendations:

For best result, do not locate the device in an area with a high rate of air
filtration and movements as the warm air will be exhausted
Try placing the device near a warmer inside wall and direct the output
toward a cooler outside wall. The cooler outside wall will tend to draw the
generated heat toward itself, which will allow for more effi cient heating.
Placing the device next to a cold air return will draw the heat away from
area to be climate. Try closing or covering the cold air return. This will
allow for more efficient heating.
To ensure maximum efficiency, a 40% (minimum) relative humidity
should be maintained in the heated environment.
When the device is placed in an isolated area (basement, recreation
area…) the delivery registers and air return grills of the existing system
should be closed in that area if possible.
In rooms with large areas of bare concrete, try placing the device a few
feet above the floor. Make sure the device is secure and won´t fall. This
will allow for more efficient heating since concrete acts as a heat sink
and will tend to draw the heat in its direction.
Try setting your central heating system to a lower temperature and
placing the device in the area you spend most of your time. Now set the
device to your control level.
When heating larger areas, place the device in a central location, if a
ceiling fan is nearby, try using it at the same time to help distribute the
heat evenly.
If used in an extremely dirty or dusty area, the filter must be cleaned
more frequently as it can clog and cause the heater to stop working.
The device grill is hot when use. To avoid burns, do not let bare skin
touch hot surface. Keep combustible materials, such as furniture,
pillows, bedding, papers, clothes, and curtains at least three feet from
the front of the device and keep them away from the sides and rear.
Extreme caution is necessary when any heater is used by or near children
or invalids and whenever the device is left operating and unattended.
To disconnect the device, press power button to “off ”, then remove plug
from outlet once it has stopped running.
Always unplug device when not in use.

WARNING

ANY REQUIRED SERVICE OTHER THAN FILTER MAINTENANCE
SHOULD ONLY BE PERFORMED BY AN AUTHORIZED SERVICE
REPRESENTATIVE

UNIT DESCRIPTION

REMOTE CONTROL

CONTROL PANEL

USING INSTRUCTION

MODE

|

HIGH MODE

|

LOW MODE

|

FAN MODE

---|---|---|---

POWER (W)

|

1000

|

800

|

21

FAN SPEED

|

Level 6-10

|

Level 4-10

|

Level 1-10

---|---|---|---

MODE

|

High Mode

|

Low Mode

|

Fan Mode

Unpackage device. Put the unit on fl at surface. Please, keep the
package for off -season storage and any transportation needs.
Put your unit on the table or a fl at surface.
Plug the power cord directly into an unused grounded 220-volt 10amp
or higher circuit receptible.
After plug into power, unit will go into Standby mode, Power indicator
will turn on and WIFI indicator will be blink, you could choose to connect
it to WIFI or not, please see WIFI function part for more information.
Press the Power button to turn on the unit then all indicators will turn on
except the Swing indicator, it will turn on after you set the swing angles.
Under working condition, you could change diff erent mode (Ventilation-
Low Heating- High Heating) by press the Mode button, the indicator
will show on accordingly. You could press the Fan speed button to set
diff erent fan speed levels under diff erent modes as bellow:
• Fan speed level under Ventilation Mode. Level 1 to 10
• Fan speed level under Low heating Mode. Level 4 to 10
• Fan speed level under High Heating Mode. Level 6 to 10
Press Light Button on both control panel and remote control to turn on
the Reading Lamp, it has two diff erent luminance, you could change
it by press the Light button either under Standby condition or Working
condition.
Press the Swing button to choose the swing angles, you could set 60,
90, 180 degrees or turn it off , the indicator will turn on accordingly after
you set the angles.
Unit has Memory function to memorize the settings before you turn off
the unit except the Light setting, you will need to set it again after you
turn on the unit.
The unit will continue to work for around 25 seconds after you turn off
the unit when it is working under Heating Mode to cool the unit.
Unit has Tip-over switch to make sure the safety, if the unit is tilted over
45 degrees over 3 seconds, then unit will turn off automatically, after you
make it upright over 3 seconds then you could turn on the unit again.

Caution: Please do not cover the air inlet and outlet during working condition.
Caution: Unplug the power cord if you do not use the unit for long time.

STORAGE AND MAINTENANCE

Turn off the unit and unplug the power cord before you clean the unit.
Use wet soft cloth to clean the unit surface.
Pack the unit into the package and keep it in a dry place.
Do not use water to clean the unit directly.
Do not use any detergent or chemicals to clean the unit in case the
chemicals cause the color change or material change.

(Please do not disassemble the unit by yourself and fi nd professionals to repair it)

WIFI FUNCTION

The WIFI indicator will blink automatically when you turn on the unit, it
will keep blinking for 3 minutes for connecting. The indicator will turn off
automatically if you do not connect WIFI, you will need to turn the unit off
and turn it on again to connect the unit to WIFI when the indicator is blinking.
Note: The unit is equipped with two pairing modes that can be distinguished
by the fl ashing speed of the WIFI indicator. Pairing can only be completed
when the WIFI indicator is fl ashing fast which is default mode. To switch
pairing mode when the WIFI indicator is fl ashing slowly, you need to press
Light/WIFI button on the control panel for 3 seconds to change the mode.

Scan above QR code to download the APP, enter your e-mail address and
complete the registration.

Connect to WIFI

Once registered, click “add device” on the main screen or use the “+”
button in the top right corner to add a new device.
Choose “Small Home Appliance “in the left part with different appliance catalogue.
Choose “Heater (Wi-Fi)”.
Connect to your preferred WIFI network and enter the corresponding password.
Follow the instructions in the app to complete the pairing process.