VTUF H1.002TT-1 Surface Cleaner Tuf Turb Instruction Manual
- June 16, 2024
- VTUF
Table of Contents
VTUF H1.002TT-1 Surface Cleaner Tuf Turb
Product Information
Specifications
- Product Code: VTUF H1.002TT-1/4F
- Product Name: SURFACE CLEANER V-TUF tufTURB
- Manufacturer: V-TUF
- Manufacturer Address: Unit 5 Chris Sharp Building, Till Bridge Lane, Scampton, Lincoln, LN1 2SX UK
Product Usage Instructions
WARNING
To reduce the risk of injection or injury, only use the surface cleaner on flat, horizontal surfaces. Never lift the surface cleaner from the cleaning surface while operating the pressure washer.
USING THE SURFACE CLEANER
- Attach the high-pressure Lance of your pressure washer to the inlet plug on the surface cleaner.
- Connect the garden hose to your pressure washer and start the pressure washer as described in your pressure washer manual.
- Walk slowly behind the cleaning deck, cleaning as you go.
- If striping or swirling occurs, slow your pace. If striping or swirling continues, the surface cleaner skirt bristles may be worn and in need of replacement.
CAUTION
Striking any raised obstacle while using the surface cleaner will damage the
unit. If contact does occur and causes vibration when operating the pressure
washer, stop and replace the spray bar.
Continuing to operate the unit without replacing the spray bar could result in
serious injury or damage to the unit.
NOZZLE MAINTENANCE
- Turn off the pressure washer and shut off the water supply.
- With the surface cleaner on the ground, pull the trigger to release water pressure.
- Disconnect surface cleaner from high-pressure Lance.
- Using a wrench (not provided), remove the nozzle from the spray bar.
- NOTE: Never point the spray bar at your face.
- Using a straightened paper clip or nozzle cleaning tool (not provided), free any foreign materials clogging or restricting the nozzle.
- Using a garden hose, flush debris out of the nozzle by the backflushing (running the water through the nozzle backward or from the outside to the inside).
- Reconnect the nozzle to the spray bar and tighten it securely.
- After tightening, make sure the nozzle opening is pointed in the same direction as the spray bar.
- Reconnect the high-pressure hose to the spray wand.
- Turn on the water supply and start the pressure washer.
FAQ
Q: What are the available replacement parts for the VTUF H1.002TT-1/4F Surface Cleaner?
A: The available replacement parts for the VTUF H1.002TT-1/4F Surface Cleaner are as follows:
| Item | Code | Description | Quantity |
|---|---|---|---|
| 1 | VTSC122 | SURFACE CLEANER – 300 BRUSH RING FOR H1.002TT-1/4F | 1 |
| 2 | VTSC132 | SURFACE CLEANER – 300 STAINLESS STEEL HOOD FOR | |
| H1.002TT-1/4F | 1 | ||
| 3 | VTSC142 | SURFACE CLEANER – ROTOR ARM FOR H1.002TT-1/4F & | |
| H1.003TT | 1 | ||
| 4 | VTSC171 | SURFACE CLEANER – SPINNER BODY with Toggle Swivel For | |
| H1.002TT-1/4F & H1.005TT | 1 |
WARNING:
- To reduce the risk of injury, users must read and understand the operator’s manual for their pressure washer before using this accessory.
- Fits most pressure washers. Ensure compatibility and proper fit before using this accessory.
- Wear eye protection marked to comply with Z87.1. Risk of fluid injections. Do not point at people, pets, electrical devices, or the unit itself.
- Turn off the pressure washer before changing or adjusting accessories.
- For cold water use only. Save these instructions. Refer to them frequently and use them to instruct other users. If you loan someone this tool, loan them these instructions also.
PRODUCT SPECIFICATIONS
- V-SPIN – High-Speed Swivel Technology
- 12″ 300mm Wide Stainless-Steel Cleaning Deck
- 4000 PSI / 275 BAR – Max Pressure
- 40 L/MIN Max Flow
- 150°C Max Temperature – Works with Soft Wash Kit
- Compatible with the V-TUF DuraKLIX SSQ Quick-Release Coupling Cleaning System
- Rigid Stainless Steel Skirt – Effective Cleaning Containing All Dirt!
- No assembly required – just connect to a pressure washer lance as shown in H1.005TT_4, H1.005TT_5
WARNING:
- To reduce the risk of injection or injury, only use the surface cleaner on flat, horizontal surfaces.
- Never lift the surface cleaner from the cleaning surface while operating the pressure washer.
USING THE SURFACE CLEANER
- Attach the high-pressure Lance of your pressure washer to the inlet plug on the surface cleaner.
- Connect the garden hose to your pressure washer and start the pressure washer as described in your pressure washer manual. Walk slowly behind the cleaning deck, cleaning as you go.
- NOTE: If striping or swirling occurs, slow your pace. If striping or swirling continues, the surface cleaner skirt bristles may be worn and in need of replacement.
CAUTION:
- Striking any raised obstacle while using the surface cleaner will damage the unit. If contact does occur and causes vibration when operating the pressure washer, stop and replace the spray bar.
- Continuing to operate the unit without replacing the spray bar could result in serious injury or damage to the unit.
- NOTE: See Figure 6 for the location of the spray bar.
NOZZLE MAINTENANCE
See Figure 6.
- Excessive pump pressure (a pulsing sensation felt while squeezing the trigger) may be the result of a clogged or dirty nozzle.
- Turn off the pressure washer and shut off the water supply. With the surface cleaner on the ground, pull the trigger to release water pressure.
- Disconnect surface cleaner from high-pressure Lance.
- Using a wrench (not provided), remove the nozzle from the spray bar.
- NOTE: Never point the spray bar at your face.
- Using a straightened paper clip or nozzle cleaning tool (not provided), free any foreign materials clogging or restricting the nozzle.
- Using a garden hose, flush debris out of the nozzle by back flushing (running the water through the nozzle backward or from the outside to the inside.
- Reconnect the nozzle to the spray bar and tighten it securely. After tightening, make sure the nozzle opening is pointed in the same direction as the spray bar as shown in Figure 4.
- Reconnect the high-pressure hose to the spray wand.
- Turn on the water supply and start the pressure washer.
OVERVIEW
| ITEM | CODE | DESCRIPTION | QTY |
|---|---|---|---|
| 1 | VTSC122 | SURFACE CLEANER – 300 BRUSH RING FOR H1.002TT-1/4F | 1 |
| 2 | VTSC132 | SURFACE CLEANER – 300 STAINLESS STEEL HOOD FOR H1.002TT-1/4F | 1 |
| 3 | VTSC142 | SURFACE CLEANER – ROTOR ARM FOR H1.002TT-1/4F & H1.003TT | 1 |
| 4 | VTSC171 | SURFACE CLEANER – SPINNER BODY |
with Toggle Swivel For H1.002TT-1/4F & H1.005TT
| 1
- www.V-TUF.COM
- Manufacturer V-TUF, Unit 5 Chris Sharp Building, Till Bridge Lane, Scampton, Lincoln, LN1 2SX UK
- Authorized Representative Established in the EU Flexrep EU OÜ, Attn: E-Residency Hub, Ahtri tn 12, 10151 Tallinn, Estonia
Documents / Resources
| VTUF
H1.002TT-1 Surface Cleaner Tuf
Turb
[pdf] Instruction Manual
H1.002TT-1 Surface Cleaner Tuf Turb, H1.002TT-1, Surface Cleaner Tuf Turb,
Cleaner Tuf Turb
---|---
Read User Manual Online (PDF format)
Loading......