GUARDIA G2-100KHX1 Bath Bench with Back and Arms Instructions
- June 16, 2024
- GUARDIA
Table of Contents
GUARDIA G2-100KHX1 Bath Bench with Back and Arms
BATH BENCH WITH BACK AND ARMS
Specifications
- Model Numbers: REF G2-100KHX1, REF G2-200KHX1
- User Weight Capacity: 350 lbs (159 kg)
General Warnings
- Prior to each use, check to assure that all screws, joints, and fittings on the bath bench are tight.
- DO NOT place the bath bench on uneven surfaces.
- DO NOT use the bath bench if it is wobbly, unstable, or not level.
- DO NOT exceed the user weight capacity of 350 lbs (159 kg).
- DO NOT stand on the bath bench.
- DO NOT twist or turn while sitting on the bath bench, as this may cause damage to the frame.
- DO NOT use the bath bench for anything other than its intended purpose.
- When using the backrest (pertains to G2-100KHX1), ensure the bench remains balanced. Excessive twisting or turning while seated on the bench may cause a loss of balance and damage to the product.
- Check rubber tips for rips, cracks, or wear. If these conditions exist, DO NOT use the bath bench and replace the tips immediately.
- Check the bench for cracks or ruptures in the plastic. If you have concerns, contact the manufacturer at 1-800-633-5463.
- Check that all push buttons are fully protruded from the main frame through the leg extensions and are properly engaged.
- Ensure all four legs are adjusted evenly and are free of any obstructions prior to use.
- When transferring in and out of the unit, evenly distribute weight between the arm supports.
Parts Listing
Ensure that you have all of the necessary components before assembling your
bath bench.
- Seat’s Main Frame Assembly
- 9 hand screws (5 short ones and 4 long ones for G2-100KHX1)
- Reinforcement bars (for G2-200KHX1)
- Backrest tubes
- Leg extension pieces
- Backrest pad
- Armrests
Assembly Instructions
- Place the seat bench upside down on top of a raised flat surface to reveal the pre-drilled holes and indentations for setting in the seat’s main frame.
- Locate the imprinted A indentation on the underside of the bench. Insert the #A main frame into the preformed indentation labeled #A.
- Locate the imprinted B indentation on the underside of the bench. Insert the #B main frame into the pre-formed #B indentation.
- Secure the center cross section using curved washer and one of the five short hand screws.
- Lay the bench on its side.
- (For G2-200KHX1 only) Attach the reinforcement bars to the bottom of the bench. Use the 4 long hand screws to attach the reinforcement bars. Insert each hand screw through the reinforcement bar and leg tube.
- Attach the backrest tubes to the bottom of the bench. Use the 4 long hand screws to attach the tubes. Insert each hand screw through the backrest tube and leg tube.
- Place a leg extension piece on each leg. Make sure that all 4 legs are adjusted to the same height.
- Stand the chair upright. Attach the backrest pad to the backrest tubes using the remaining 4 short screws.
- Insert one armrest on each side. The armrest should lean to the outside of the chair.
- Your chair should now be complete.
FAQ
-
Q: What is the weight capacity of the bath bench?
A: The weight capacity of the bath bench is 350 lbs (159 kg). -
Q: Can I use the bath bench if it is wobbly or unstable?
A: No, DO NOT use the bath bench if it is wobbly, unstable, or not level. Ensure that all screws, joints, and fittings are tight before use. -
Q: How do I check if the bath bench is safe for use?
A: Prior to each use, check that all screws, joints, and fittings are tight. Also, check for any cracks or ruptures in the plastic and ensure that all four legs are adjusted evenly and free of any obstructions. -
Q: What should I do if the rubber tips are damaged?
A: If the rubber tips have rips, cracks, or wear, DO NOT use the bath bench and replace the tips immediately.
BATH BENCH WITH BACK AND ARMS
USER INSTRUCTIONS & WARRANTY
Not Made With Natural Rubber Latex.
General Warnings
- To ensure the safe installation, adjustment, and operation of the Bath Bench, these instructions MUST be followed.
- FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN SERIOUS INJURY TO THE USER OR DAMAGE TO THE PRODUCT. If you are unable to understand these warnings, cautions, and instructions, contact a healthcare professional or dealer before attempting to use this equipment.
Warnings:
- Prior to each use check to assure that all screws, joints and fittings on the bath bench are tight.
- DO NOT place bath bench on uneven surfaces.
- DO NOT use if wobbly, unstable or not level.
- DO NOT exceed user weight capacity of 350 lbs (159 kg).
- DO NOT stand on the bath bench.
- DO NOT twist or turn while seating on the bath bench, this may cause damage to the frame.
- DO NOT use the bath bench for anything but its intended purpose.
- When using the back rest, ensure the bench remains balanced. Excessive twisting or turning while seated on the bench may cause a loss of balance and damage to the product. (Only pertains to G2-100KHX1)
- Check rubber tips for rips, cracks or wear. If these conditions exist, DO NOT use the bath bench and replace the tips immediately.
- Check the bench for cracks or ruptures in the plastic. If you have concerns, contact the manufacturer at 1-800-633-5463.
- Check that all push buttons are fully protruded from the main frame through the leg extensions and are properly engaged.
- Ensure all four legs are adjusted evenly and are free of any obstructions prior to use.
- When transferring in and out of unit, evenly distribute weight between the arm supports.
Parts Listing
Ensure that you have all of the necessary components before assembling your bath bench.
- 1 (each) Bench (Imprinted with an A and B)
- 2 (each) Aluminum Main Frames (imprinted A and B)
- 4 (each) Aluminum Extension Legs
- 2 (each) Padded Arm Rests
- 1 (each) Backrest (Only pertains to G2-100KHX1)
- 9 (each) Hand Screws for G2-100KHX1
- 5 (each) Hand Screws for G2-200KHX1
- 2 (each) Aluminum Backrest Frames (only G2-100KHX1)
- 1 (each) Curved Washer
- 2 Reinforcement Bars (only G2-200KHX1)
Assembly Instructions
Seat’s Main Frame Assembly:
- Place the seat bench upside down on top of a raised flat surface to reveal the pre-drilled holes and indentations for setting in the seat’s main frame.
- You should have received a total of 9 hand screws, 5 short ones and 4 long ones (for G2-100KHX1).
- Locate the imprinted “A” indentation on the underside of the bench. Insert the #A main frame into the preformed indentation labeled #A.
- Locate the imprinted “B” indentation on the underside of the bench. Insert the #B main frame into the pre-formed #B indentation.
- Secure the center cross section using curved washer and one of the five short hand screws.
- Lay the bench on its side.
- (For G2-200KHX1 only) Attach the reinforcement bars to the bottom of the bench. Use the 4 long hand screws to attach the reinforcement bars. Insert each hand screw through the reinforcement bar and leg tube.
- Attach the backrest tubes to the bottom of the bench. Use the 4 long hand screws to attach the tubes. Insert each hand screw through the back rest tube and leg tube.
- Place a leg extension piece on each leg. Make sure that all 4 legs are adjusted to same height.
- Stand the chair upright. Attach the back rest pad to the back rest tubes using the remaining 4 short screws.
- Insert one arm rest on each side. The armrest should lean to the outside of the chair.
- Your chair should now be complete.
Attach the Aluminum Extension Legs to the Aluminum Main Frame:
Depress the pushbuttons on the main frame and place the aluminum extension
legs into the main frame tube until secured at the desired height. Repeat with
the three remaining legs. Ensure all four extension legs are installed at the
same height and the push-buttons are fully protruded before using.
Note: Improperly inserting the legs of the backrest may cause damage to the product. When the legs have been installed to the seat bench, the legs of the backrest will hangover the side of the table and are pointing towards the floor.
Installing and Assembling the Back Rest: (Only pertains to G2-100KHX1)
- Hold one tube of the aluminum backrest frame so that the pushbuttons are facing upwards; slide the tube into the cross brace so that the brass pushbuttons protrude upward from the bracket’s hole and lock into place. The aluminum backrest frame has two adjustable settings. Repeat with the second tube of the aluminum back rest frame. Turn the bench right side up.
- Place the bench right side up to assemble the backrest to the aluminum backrest frame.
- Grab the backrest by the handle and position it into place fitting the pre-formed indentations located on the backside of the backrest so that the screw holes line up to the predrilled holes of the aluminum backrest frame. Attach and secure the hand screw. Once all four screws are in place, tighten for safety.
Assembling the Arm Rests:
Insert each padded arm rest on either side of the seat bench. Ensuring the
curved bar extends outward from the seat bench. The pushbuttons should lock
securely into place.
Adjusting the Bench to the Proper Height:
- While standing in front of the assembled bench, as if preparing to sit, the back of the users knees should touch the front side of the seat bench. This should allow the users feet to be firmly on the floor while properly seated. Adjust the leg extensions as needed.
- Ensure all four rubber tips rest evenly on the floor.
Cleaning
The bath bench can be easily cleaned with regular household cleaning products. Use a non-abrasive cleaner with warm water. DO NOT use abrasive powders or scouring pads.
Maintenance
- Periodically inspect the bath bench for damage or loose components.
- Ensure all pushbuttons are protruded from the extension legs.
- Check the rubber feet on the leg extensions for rips or wear. If any of these conditions exist, or if they are missing, replace them immediately.
LIMITED WARRANTY
- Your Medline product is warranted to be free of defects in materials and workmanship for the duration of use by the original purchaser. This device was built to precise standards and carefully inspected prior to shipment. This limited warranty is an expression of our confidence in the materials and workmanship of our products and assures years of convenient, dependable service. In the event of a defect covered by this warranty, we will, at our option, repair or replace the device. This warranty does not cover device failure due to owner misuse or negligence, or normal wear and tear.
- The warranty does not extend to non-durable components, such as rubber accessories, which are subject to normal wear and replacement.
Medline Industries, LP, Three Lakes Drive, Northfield, IL 60093 USA.
- Medline United States
- 1-800-MEDLINE (633-5463)
- www.medline.com | info@medline.com
Medline Canada
1-800-268-2848
www.medline.ca |
Canada@medline.com
Medline Mexico
1-800-831-0898
www.medlinemexico.com |
mexico@medline.com
© 2020 Medline Industries, LP
- Medline is a registered trademark of Medline Industries, LP. Guardian is a registered trademark of Medline Industries, LP.
- Some products may not be available for sale in Mexico or Canada.
- Please contact your Account Representative for additional information.
- We reserve the right to correct any errors that may occur within this manual.