gridinlux WALK-2100 Walking Pad Under Desk Treadmill Instruction Manual

TRAINER WALK 2100 MANUAL

Warnings & Safety Precautions

Before starting to use the treadmill, verify that you have hooked the clip of the Security key in the indicated place on the main panel. If it is not connected, the tape will not work.

• For safety reasons, do not turn the treadmill on before you are actually on it.
• If the treadmill is moving and you are not on it, please stop the device and then get on it. Do not attempt to get on it while it is moving.
• If you feel nauseous or if the treadmill is not running properly while you are using it, stop using it immediately.
• Never try to manipulate the belt of the treadmill directly while it is in operation.
• When you want to increase the speed, do so progressively. We recommend you wear sneakers and sportswear when using the treadmill.
• Children, the elderly and pregnant women should not use the machine. People suffering from any type of ailment should consult with their doctor before using the machine.
• Attach the safety clip to your clothing when using the machine. Keep a firm hold on the handles when using the machine.
• Install the treadmill on a flat, level surface. Do not install the machine in the following locations:
  • Outdoors. (The machine has been designed exclusively for indoor use.)
  • Inclined surfaces or on terraces.
  • Places exposed to bright sunlight or near heating appliances.
  • Do not connect the machine to the same socket as other electrical appliances (computers, air conditioning, etc.) to avoid voltage spikes since these can trigger treadmill errors.
  • Be careful when folding or unfolding the machine next to children or objects.
  • Keep the machine away from wet objects. Water could cause a malfunction.

Precautions during use

• If you don’t feel well before getting on the treadmill, consult with your doctor or trainer.
• Our company is exempt from any liability for bodily injury caused by improper use.
• Unplug the machine after use.
• Always unplug the machine when moving it or when changing parts.
• Place the machine on a smooth, flat surface. Do not place objects within 2 meters of the machine.
• Do not turn on the machine when it is folded up.
• Never put water in the machine, especially in the motor, power cord and electrical outlet.
• Do not wear loose or unsuitable clothing when using the machine as this can be dangerous.
• Do not use the machine in small, non-ventilated or flammable areas.
• Do not place objects on the treadmill.
• Keep the machine’s electrical plug well away from sources of heat or fire.
• Always turn off all the functions and unplug the machine after use.
• Do not disassemble the machine without instructions from a professional.
• Make sure the belt is securely fastened before using the machine.

Instructions for setting up the machine:

1. Main Structure
2. Security key
3. Treadmill foot protections + screws (x2)
4. ST4.2 * 16 screw + washer (x2)
5.M12 screw| 6. M16 screw
7. Handrail Cover (x2)
8. Silicone Oil
9. Tool 1
10. Tool 2
---|---

1. With the assistance of another person, lift the frame and while one person holds the handrail, the other shall fix the handrail to the frame with the set of screws provided, using the proper wrench. Connect the cables, making sure that they are connected in the right direction.
2. Now remove the 2 ST4 screws and 2 washers and use these to mount the console on the upright tubes. Tighten the screws, and add parts 7 (Handrail Covers). Before tightening the screws, make sure that they do not press on the cables of the upright tubes.
3. Fasten the M16 screw to the left vertical tube and attach it to the frame using the M12 screw.
4. Adjust the tilt angle of the console to your desired height using the plastic M6 screw and attach the safety clip to the console.
5. Fix the 3 pieces (Treadmill foot protections + screws) on the structure.

Console

1. Press the “INICIO” button and after 3 seconds the machine will switch on at a speed of 1.0 km/h.

2. Press the “A” button to increase the speed and the“ ¥” button to decrease it. The maximum speed is 10 km/h; the minimum is 1.0 km/h.

3. Press the “MODE” button to display the speed, time and calories on the console.
   ● SCAN: It shows 1 in 1 every 30 seconds the different registers: VELOCIDAD | TIEMPO | CALORIAS.
   ● VELOCIDAD: Displays the speed during workout.
   ● TIEMPO: Measures the time of each workout.
   ● CALORIAS: Calculates calories burnt during workout.

4. The treadmill has 12 programmes that can be activated by pressing “PROG”. To select a programme, press “PROG” when the machine is in standby mode. Then press “INICIO” to start the treadmill. * When using the treadmill with an “automatic” programme, the “▲”|”▼” button is disabled.

5. To stop the machine in case of emergency, just pull out the safety clip. The machine will stop. When you remove the safety clip, “Err” appears on the display. When you reinsert it, “OFF* will appear on the display.

6. Press “STOP” to switch the machine off after use.

Folding and unfolding:

Folding:
Loosen the locking screw and raise the running surface to fold the machine. Pull the retaining screw on the side of the tube and release it to secure the machine. You can now move the machine.

Unfolding:
Pull on the retaining screw, unfold the running surface and tighten the locking screw. Once it is plugged in, the treadmill is ready to use

Using silicone oil
It is recommended that every 30 hours of use or after noticing that the tape no longer slide smoothly, apply a silicone lubricant to the points of contact between the tape and the mai structure.
To do this, you must lift the tape and apply silicone oil on both sides of the structure where the tape slides. After doing this, turn on the machine and keep it running without getting on it for 3 minutes.

Adjusting the belt
The belt deflects to the left…
Start the machine at a speed of 2 to 3 km/h without load and use the Tool 1 to turn the treadmill adjustment screw a quarter turn . Keep the machine running unloaded for 1 to 2 minutes. Perform this process until the belt moves in an aligned and straight line.

The belt deflects to the right…
Start the machine at a speed of 2 to 3 km/h without load and use the Tool 1 to turn the treadmill adjustment screw a quarter turn. Keep the machine running unloaded for 1 to 2 minutes. Perform this process until the belt moves in an aligned and straight line.

The belt is locked…
Use Tool 1 to turn the adjustment screws on both sides of the tape and turn them half a turn clockwise until they are unlocked. If it is still stuck, turn the two screws half a turn until it works properly.

Daily maintenance

• Make sure the machine is unplugged before carrying out any maintenance or cleaning.
• Clean the belt and console at least once a week after use.
• Check that the screws are tightened properly.
• Do not hang clothes or other objects on the machine.

(red) to the main panel.
E2| The control panel is broken.| Replace control panel.
E4| The control panel is broken.| Replace control panel.
E5| The control panel is locked or the main engine is locked.| Contact your service representative.
E6| Engine failure.| Contact your service representative.
E7| Panel connection failed.| Verify that the panel cables are well connected and in perfect condition. If all is well, contact the technical service.
E8| Safety lock due to power overload or belt weight.| Verify that people who use the tape do not exceed the maximum weight suppor- ted. Disconnect the tape from the mains. Reconnect the tape and turn it on again. If the problem persists, contact the technical service.

IMPORTER: B85960425 gridinlux.es
Gridinlux S.L.U.
CIF: B86889458

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>