ANPVIZ 21725 NVR PoE Uprime Camera Parameters User Guide

ANPVIZ 21725 NVR PoE Uprime Camera Parameters

Anpviz NVR PoE Uprime Camera

Specifications

• Model: Anpviz NVR PoE Uprime
• Power over Ethernet (PoE) support: Yes
• Network Video Recorder (NVR) support: Yes
• Resolution: Depending on the camera connected
• Camera Configuration: Motion detection, intelligent detection, image parameters, light mode settings, etc.
• Software Compatibility: SADP search tool

Product Usage Instructions

Step 1: Install SADP or Search Tool

Download the SADP or Search Tool from the official Anpviz website:

• SADP
• Download
• Uptime
• Search Tool Download

Step 2: Connect your PC to the NVR PoE Port

• If you do not have a standalone PoE switch, connect your PC to the NVR PoE port using an Ethernet cable.

Step 3: Configure PC IP Address

• Change your PC’s IP address to match the NVR PoE port IP subnet configuration.
• For example, if the IP of the NVR PoE port is 192.168.254.xx, change the PC’s IP to the same network segment, such as 192.168.254.xxx.
• This will form a local area network and allow you to access and configure the camera.

Step 4: Run the SADP Search Tool

• Launch the SADP search tool that you installed in Step 1 and follow the on-screen instructions.

Step 5: Access the Camera Web Page

• Open a web browser and enter the camera’s IP address to access the camera’s web page.

Step 6: Configure Camera Settings

• Navigate to the camera configuration section, specifically the “Event” settings. Here, you can configure various parameters such as motion detection, intelligent detection, camera image parameters, light mode settings, etc.

FAQ

• Q: How can I download the SADP or Search Tool?
• A: You can download the SADP or Search Tool from the official Anpviz website. Visit the following links to download:
• SADP Download Uprime Search Tool Download
• Q: Can I connect the NVR PoE Uprime camera to a standalone PoE switch?
• A: Yes, you can connect the NVR PoE Uprime camera to a standalone PoE switch if you have one available.
• Q: What can I configure in the camera settings?
• A: In the camera settings, you can configure various parameters such as motion detection, intelligent detection, camera image parameters, light mode settings, etc.

How to set Anpviz NVR PoE Uprime camera parameters

1. Install the SADP or search tool, and download it from
   https://www.anpvizsecurity.com/download-21725 SADP.
   https://www.anpvizsecurity.com/download-21724 uptime search tool

2. Connect your PC to the NVR PoE port if you do not have a standalone PoE switch.

3. Change your PC IP address to suit your NVR PoE port IP subnet configuration.
   If the IP of the NVR POE port is 192.168.254.xx, change the PC’s IP to the same network segment as the NVR POE, that is,192.168.254.xxx forms a local area network, you can log in to the camera through the browser, reset the camera or update the camera software.

4. Run the SADP search tool and operate following the steps below:

5. Log in to the camera IP address through the browser to enter the web page.

6. Go to camera configuration-Event, and set the motion detection or intelligent detection.

Camera image parameters and light mode settings, etc.

Documents / Resources

| ANPVIZ 21725 NVR PoE Uprime Camera Parameters [pdf] User Guide
21725 NVR PoE Uprime Camera Parameters, 21725, NVR PoE Uprime Camera Parameters, PoE Uprime Camera Parameters, Uprime Camera Parameters, Camera Parameters, Parameters
---|---

References

• Security IP camera
• Security IP camera

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>