Turbomax BTH ULTRA 30-3 30 Instantaneous Indirect Water Heater Instruction Manual

June 15, 2024
Turbomax

BTH ULTRA 30-3 30 Instantaneous Indirect Water Heater

Product Information: Instantaneous Indirect Water Heater

Specifications:

  • Boiler Capacity: __ BTU/H
  • Minimum Required Net Capacity: __ BTU/H
  • Pump Capacity: __GPM @ __ Feet of Head
  • Boiler Pipe Connection Size: __ in
  • DHW Turbomax Pipe Connection Size: __ in
  • Boiler Model: __
  • Turbomax Model: __

Product Usage Instructions:

Installation Requirements:

  1. The installation must conform to local, state, provincial, and
    national codes. In any case where instructions conflict with the
    above, let those codes take precedence.

  2. This is a basic piping schematic. Please consult the
    installation manual for detailed instructions.

  3. Install a safety valve (temperature & pressure) on the
    domestic hot water line, as close as possible to the hot water
    heater(s) connection(s) and before any shut-off valve.

  4. Pipe all the safety valves and drain valves to the drain or
    accordingly to the code.

  5. If a backflow preventer, water meter, or a pressure reducing
    valve is used on the domestic cold water supply line, then a
    thermal expansion tank must be installed between the water heater
    and this device.

  6. Note that the drawing provided is not to scale.

Symbols:

  • Ball Valve
  • Check Valve
  • Backflow Preventer
  • Pressure Reducing Valve
  • Drain Cock
  • Balancing Valve
  • Automatic Air Vent
  • Pump
  • Air Separator
  • Sensor Well
  • Expansion Tank
  • Thermometer
  • Pressure Relief Valve
  • Temperature & Pressure Relief Valve
  • Thermostatic Mixing Valve

Connection Diagram:

Frequently Asked Questions:

Q: What are the requirements for installation?

A: The installation must conform to local, state, provincial,
and national codes. Please consult the installation manual for
specific requirements.

Q: What is the purpose of the safety valve?

A: The safety valve (temperature & pressure) ensures that
the domestic hot water line is protected from excessive temperature
and pressure.

Q: When should a thermal expansion tank be installed?

A: A thermal expansion tank should be installed between the
water heater and a backflow preventer, water meter, or pressure
reducing valve on the domestic cold water supply line.

TurboMax ®
Instantaneous Indirect Water Heater
TURBOMAX INSTALLATION DRAWINGS
Revision January 2023

BASIC INSTALLATION DRAWING FOR:
1 x TURBOMAX 1 x BOILER

TP P

BOILER

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

TURBOMAX

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BTH ULTRA 2 x BASEBOARD

TP P P

BASEBOARDS

BTH ULTRA

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

TURBOMAX

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR:
1 x TURBOMAX 1 x BOILER
2 x BASEBOARD
Close T

TP P

BASEBOARDS

BOILER

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

TURBOMAX

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR:
1 x TURBOMAX 1 x BOILER
2 x RADIANT FLOORS

TP P

Close T

RADIANT FLOORS

BOILER

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

TURBOMAX

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 2 x BASEBOARD

TP P

For this piping, it’s required to have hot water priority. Here’s two methods to do so : 1) Replace the factory aquastat by one with
a dual output signal 2) Replace the manometer by a second
aquastat
BASEBOARDS

BOILER

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER
2 x RADIANT FLOORS

TP P

For this piping, it’s required to have hot water priority. Here’s two methods to do so : 1) Replace the factory aquastat by one with
a dual output signal 2) Replace the manometer by a second
aquastat

BOILER

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

RADIANT FLOORS

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TurboMax 1 x Boiler 1 x BuffMax 2 x Baseboards

TP P

BASEBOARDS

BOILER

BUFFMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

TURBOMAX

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TurboMax 1 x Boiler 1 x BuffMax
2 x RADIANT FLOORS

TP P

BOILER

BUFFMAX

TURBOMAX

RADIANT FLOORS

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x BTH ULTRA 2 x BASEBOARD
TP
P

CLOSE T

BASEBOARDS
CLOSE T CLOSE T
P

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

BOILER

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

BTH ULTRA

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x BTH ULTRA
2 x RADIANT FLOORS
TP
P

CLOSE T

RADIANT FLOORS
CLOSE T CLOSE T
P

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

BOILER

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

BTH ULTRA

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x BTH ULTRA 2 x BASEBOARD

For this piping, it’s required to have hot water priority. Here’s two methods to do so : 1) Replace the factory aquastat by one with
a dual output signal 2) Replace the manometer by a second
aquastat

CLOSE T

CLOSE T

P
BTH ULTRA

TP P

BASEBOARDS

BOILER

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x BTH ULTRA
2 x RADIANT FLOORS
CLOSE T

TP P P

For this piping, it’s required to have hot water priority. Here’s two methods to do so : 1) Replace the factory aquastat by one with
a dual output signal 2) Replace the manometer by a second
aquastat

BTH ULTRA

BOILER

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

RADIANT FLOORS

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

PREHEATING DOMESTIC HOT WATER THROUGH A TURBOMAX USING A HEAT PUMP OR GEOTHERMAL APPLICATION
TP P
TP

HEAT PUMP OR GEOTHERMAL

TURBOMAX

CONVENTIONAL WATER HEATER

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 2 x BOILER
2 x TURBOMAX WITH RECIRCULATION

RECIRCULATION IS RECOMMENDED FOR COMMERCIAL INSTALLATIONS

TP P

TP P

BOILER

BOILER

TURBOMAX

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

PRIMARY/SECONDARY SETUP FOR : 2 x TURBOMAX 2 x BOILER 2 x BASEBOARD
BASEBOARDS

CLOSE T CLOSE T

CLOSE T

RECIRCULATION IS RECOMMENDED FOR COMMERCIAL INSTALLATIONS

TP P

TP P

BOILER

BOILER

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

TURBOMAX

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

TURBOMAX

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 2 x VOLTMAX
2 x BASEBOARD 2 x TURBOMAX WITH RECIRCULATION
BASEBOARDS

RECIRCULATION IS RECOMMENDED FOR COMMERCIAL INSTALLATIONS

TP P

TP P

VOLTMAX

VOLTMAX

TURBOMAX

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

PRIMARY/SECONDARY INSTALLATION: 1 x BOILER
1 x VOLTMAX 2 x BASEBOARD 2 x TURBOMAX WITH RECIRCULATION

RECIRCULATION IS RECOMMENDED FOR COMMERCIAL INSTALLATIONS

TP

TP

P

P

CLOSE T

BASEBOARDS

CLOSE T CLOSE T

CLOSE T

TURBOMAX

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

BOILERS

VOLTMAX

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 2 x VOLTMAX 2 x BUFFMAX
2 x BASEBOARD 2 x TURBOMAX WITH RECIRCULATION

RECIRCULATION IS RECOMMENDED FOR COMMERCIAL INSTALLATIONS
TP P

TP P

BASEBOARDS

VOLTMAX

VOLTMAX

BUFFMAX

BUFFMAX

TURBOMAX

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x DHW TANK

TP
TP
P

BOILER

TURBOMAX

DHW TANK

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

BASIC INSTALLATION DRAWING FOR: 1 x TURBOMAX 1 x BOILER 1 x DHW TANK 2 x BASEBOARD

TP
TP
P

BASEBOARDS

BOILER

TURBOMAX

REQUIREMENTS 1. THE INSTALLATION MUST CONFORM TO LOCAL, STATE, PROVINCIAL, NATIONAL CODES. IN ANY CASE WHERE INSTRUCTIONS CONFLICT WITH THE ABOVE, LET THOSE CODES TAKE PRECEDENCE
2. THIS IS A BASIC PIPING SCHEMATIC. PLEASE CONSULT THE INSTALLATION MANUAL
3. INSTALL A SAFETY VALVE (TEMPERATURE & PRESSURE) ON THE DOMESTIC HOT WATER LINE, THE NEAREST POSSIBLE TO THE HOT WATER HEATER(S) CONNECTION(S) AND BEFORE ANY SHUT OFF VALVE
4. PIPE ALL THE SAFETY VALVES AND DRAIN VALVES TO THE DRAIN OR ACCORDINGLY TO THE CODE
5. WHEN A BACK FLOW PREVENTER OR WATER METER OR A PRESSURE REDUCING VAVLE IS USED ON THE DOMESTIC COLD WATER SUPPLY LINE, THEN A THERMAL EXPANSION TANK MUST BE INSTALLED BETWEEN THE WATER HEATER AND THIS DEVICE
6. THIS DRAWING IS NOT TO SCALE

SYMBOLS

BALL VALVE
CHECK VALVE
BACK FLOW PREVENTER PRESSURE REDUCING VALVE
DRAIN COCK
BALANCING VALVE

AUTOMATIC AIR VENT
PUMP
AIR SEPERATOR
SENSOR WELL
EXPANSION TANK

THERMOMETER

P
PRESSURE RELIEF VALVE

TP

TEMPERATURE

& PRESSURE

RELIEF VALVE

THERMOSTATIC MIXING VALVE

COLD WATER SUPPLY DOMESTIC PREHEATED WATER / DHW RECIRCULATION DOMESTIC HOT WATER HEATING HOT WATER/FLUID
HEATING WATER/FLUID RETURN

DHW TANK

BOILER CAPACITY : MINIMUM REQUIRED NET CAPACITY :

__ BTU/H __ BTU/H

PUMP CAPACITY :

__GPM @ __ FEET OF HEAD

BOILER PIPE CONNECTION SIZE : DHW TURBOMAZ PIPE CONNECTION SIZE :

____ in ____ in

BOILER MODEL :


TURBOMAX MODEL : __

500 9th AVENUE RICHMOND, QC, CA, J0B 2H0 T : 1 819 826-5613 F : 819 826-6370

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals