Honeywell Voyager 1350g Corded Area Imaging Scanner User Guide

: June 15, 2024
: Honeywell

Voyager 1350g Corded Area Imaging Scanner

Product Information: VoyagerTM 1350g Corded Area-Imaging

Scanner

Specifications:

Scanner Type: Area-Imaging
Connectivity: Corded
Interface: USB
Supported Symbologies: Code 39, Code 128, UPC, EAN, PDF417,
Data Matrix, etc.

Chapter 1 – Get Started

About This Manual

The VoyagerTM 1350g Corded Area-Imaging Scanner User Guide
provides detailed information on how to use the scanner
effectively.

Unpack Your Device

When you receive your VoyagerTM 1350g scanner, ensure that all
the components are included in the package. The package should
contain:

VoyagerTM 1350g scanner
USB cable
User Guide

Connect the Device

To connect the VoyagerTM 1350g scanner to your computer, follow
these steps:

Locate the USB port on your computer.
Plug one end of the USB cable into the USB port on your
computer.
Plug the other end of the USB cable into the USB port on the
scanner.
The scanner will be ready to use once it is connected.

Chapter 2 – Program the Interface

In this chapter, you will learn how to program the interface of
the VoyagerTM 1350g scanner.

USB Serial

To program the USB serial interface, follow these steps:

Refer to the user guide for the specific programming
barcodes.
Scan the programming barcode corresponding to the desired USB
serial interface configuration.
The scanner will now be programmed with the selected USB serial
interface.

CTS/RTS Emulation

To program the CTS/RTS emulation mode, follow these steps:

Refer to the user guide for the specific programming
barcodes.
Scan the programming barcode corresponding to the desired
CTS/RTS emulation mode.
The scanner will now be programmed with the selected CTS/RTS
emulation mode.

ACK/NAK Mode

To program the ACK/NAK mode, follow these steps:

Refer to the user guide for the specific programming
barcodes.
Scan the programming barcode corresponding to the desired
ACK/NAK mode.
The scanner will now be programmed with the selected ACK/NAK
mode.

Chapter 3 – Input/Output Settings

This chapter provides information on configuring input/output
settings for the VoyagerTM 1350g scanner.

Chapter 4 – Data Edit

This chapter explains how to edit data captured by the VoyagerTM
1350g scanner.

Chapter 5 – Data Format

This chapter covers data formatting options available for the
VoyagerTM 1350g scanner.

Data Format Editor Introduction

The Data Format Editor allows you to customize the format of the
scanned data.

Show Data Format

To view the current data format settings, follow these
steps:

Refer to the user guide for the specific programming
barcodes.
Scan the programming barcode to display the current data format
settings.

Add a Data Format

To add a new data format, follow these steps:

Refer to the user guide for the specific programming
barcodes.
Scan the programming barcode to enter the data format editor
mode.
Follow the instructions in the user guide to customize the data
format.

Chapter 6 – Symbologies

This chapter provides information on the symbologies supported
by the VoyagerTM 1350g scanner.

Planet Code Check Digit

The scanner supports the Planet Code check digit feature. Refer
to the user guide for more information on how to enable and use
this feature.

Postnet Check Digit

The scanner supports the Postnet Check Digit feature. Refer to
the user guide for more information on how to enable and use this
feature.

Australian Post Interpretation

The scanner supports Australian Post Interpretation. Refer to
the user guide for more information on how to enable and use this
feature.

FAQ

Q: Where can I find patent information for the VoyagerTM 1350g

scanner?

A: For patent information, please refer to www.hsmpats.com.

VoyagerTM 1350g
Corded Area-Imaging Scanner
User Guide

Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII. HII shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. HII disclaims all responsibility for the selection and use of software and/or hardware to achieve intended results.
Trademarks
Microsoft, Windows and the Windows logo are registered trademarks of Microsoft Corporation in the United States and/or other countries. The Bluetooth trademark is owned by Bluetooth SIG, Inc., U.S.A. and licensed to Honeywell. Other product names or marks mentioned in this document may be trademarks or registered trademarks of other companies and are the property of their respective owners.
Patents
For patent information, refer to www.hsmpats.com.

TABLE OF CONTENTS

Customer Support ………………………………………………………………………………………………………. xiii Technical Assistance …………………………………………………………………………………………….. xiii Product Service and Repair …………………………………………………………………………………. xiii Limited Warranty …………………………………………………………………………………………………… xiii
Chapter 1 – Get Started ………………………………………………………………………… 1
About This Manual…………………………………………………………………………………………………………. 1 Unpack Your Device……………………………………………………………………………………………………….. 1 Connect the Device………………………………………………………………………………………………………… 2
Connect with USB…………………………………………………………………………………………………….. 2 Connect with RS232 Serial Port ……………………………………………………………………………. 3 Reading Techniques………………………………………………………………………………………………………. 3 Troubleshooting ……………………………………………………………………………………………………….. 4 Menu Barcode Security Settings ………………………………………………………………………………… 4 Set Custom Defaults ……………………………………………………………………………………………………… 4 Reset the Custom Defaults…………………………………………………………………………………………… 5
Chapter 2 – Program the Interface ………………………………………………………. 7
Introduction…………………………………………………………………………………………………………………….. 7 Program the Interface – Plug and Play………………………………………………………………………. 7 RS232 Serial Port …………………………………………………………………………………………………………… 7 USB IBM SurePos…………………………………………………………………………………………………………… 8 USB PC or Macintosh Keyboard………………………………………………………………………………….. 8 USB HID …………………………………………………………………………………………………………………………… 9

Voyager 1350g User Guide

iii

USB Serial …………………………………………………………………………………………………………………………9 CTS/RTS Emulation ………………………………………………………………………………………………….9 ACK/NAK Mode………………………………………………………………………………………………………….9
Secondary Interface for USB………………………………………………………………………………………10 Keyboard Country Layout……………………………………………………………………………………………10 Keyboard Wedge Modifiers…………………………………………………………………………………………17
ALT Mode ………………………………………………………………………………………………………………….17 Keyboard Style ………………………………………………………………………………………………………………18 Keyboard Conversion …………………………………………………………………………………………………..19 Control Character Output……………………………………………………………………………………………19 Keyboard Modifiers………………………………………………………………………………………………………20 RS232 Modifiers …………………………………………………………………………………………………………..21
RS232 Baud Rate ……………………………………………………………………………………………………21 RS232 Word Length: Data Bits, Stop Bits, and Parity ……………………………………..22 RS232 Receiver Time-Out …………………………………………………………………………………….23 RS232 Handshake ………………………………………………………………………………………………….24 RS232 Timeout………………………………………………………………………………………………………..24 XON/XOFF ………………………………………………………………………………………………………………. 25 ACK/NAK ………………………………………………………………………………………………………………….25
Chapter 3 – Input/Output Settings……………………………………………………. 27
Power Up Beeper…………………………………………………………………………………………………………..27 Beep on BEL Character ……………………………………………………………………………………………….27 Trigger Click …………………………………………………………………………………………………………………..28 Good Read and Error Indicators ………………………………………………………………………………..28
Beeper Good Read……………………………………………………………………………………………….28 Beeper Volume Good Read ………………………………………………………………………………..28 Beeper Pitch Good Read …………………………………………………………………………………….29 Beeper Pitch Error ……………………………………………………………………………………………….29 Beeper Duration Good Read………………………………………………………………………………30 LED Good Read ……………………………………………………………………………………………………30 Number of Beeps Good Read…………………………………………………………………………….30 Number of Beeps Error……………………………………………………………………………………….30

Voyager 1350g User Guide

Good Read Delay……………………………………………………………………………………………………..31 User-Specified Good Read Delay …………………………………………………………………………31 Trigger Modes………………………………………………………………………………………………………………..32 Manual Trigger ………………………………………………………………………………………………………..32 Serial Trigger…………………………………………………………………………………………………………….32 Presentation Mode ……………………………………………………………………………………………………….33 Presentation LED Behavior after Decode…………………………………………………………..33 Presentation Centering ………………………………………………………………………………………….33 In-Stand Sensor Mode …………………………………………………………………………………………………35 Poor Quality Codes……………………………………………………………………………………………………….35 Poor Quality 1D Codes …………………………………………………………………………………………..35 Poor Quality PDF Codes…………………………………………………………………………………………36 Low Resolution PDF Codes …………………………………………………………………………………..36 CodeGateTM ……………………………………………………………………………………………………………………..36 Streaming Presentation Mode……………………………………………………………………………………37 Hands Free Time-Out …………………………………………………………………………………………………..37 Reread Delay ………………………………………………………………………………………………………………….38 User-Specified Reread Delay ………………………………………………………………………………..38 2D Reread Delay ……………………………………………………………………………………………………..38 Character Activation …………………………………………………………………………………………………….39 Activation Character……………………………………………………………………………………………….39 End Character Activation After Good Read ………………………………………………………..40 Character Activation Timeout……………………………………………………………………………….40 Character Deactivation………………………………………………………………………………………………..40 Deactivation Character ………………………………………………………………………………………….41 Illumination Lights ……………………………………………………………………………………………………….41 Aimer Delay…………………………………………………………………………………………………………………….41 User-Specified Aimer Delay…………………………………………………………………………………..42 Aimer Mode ……………………………………………………………………………………………………………………42 Centering ………………………………………………………………………………………………………………………..42 Single Code Centering……………………………………………………………………………………………43 Custom Centering …………………………………………………………………………………………………..43 Preferred Symbology ……………………………………………………………………………………………………44

Voyager 1350g User Guide

High Priority Symbology ……………………………………………………………………………………….45 Low Priority Symbology …………………………………………………………………………………………45 Preferred Symbology Time- out…………………………………………………………………………….46 Preferred Symbology Default ……………………………………………………………………………….46 Output Sequence Overview ………………………………………………………………………………………..46 Output Sequence Editor………………………………………………………………………………………..46 To Add an Output Sequence …………………………………………………………………………………46 Output Sequence Editor Commands………………………………………………………………………..47 Enter Output Sequence……………………………………………………………………………………………….50 Partial Sequence …………………………………………………………………………………………………….50 Good Read Tone – Output Sequences…………………………………………………………………54 Multiple Symbols ………………………………………………………………………………………………………….54 No Read ………………………………………………………………………………………………………………………….55 Video Reverse ………………………………………………………………………………………………………………..55
Chapter 4 – Data Edit …………………………………………………………………………. 57
Prefix/Suffix Overview …………………………………………………………………………………………………57 Points to Keep In Mind …………………………………………………………………………………………..57 Add a Prefix or Suffix:……………………………………………………………………………………………..58 Example: Add a Tab Suffix to All Symbologies…………………………………………………..58 Clear One or All Prefixes or Suffixes ……………………………………………………………………58 Add a Carriage Return Suffix to All Symbologies ……………………………………………..59
Prefix Selections……………………………………………………………………………………………………………59 Suffix Selections……………………………………………………………………………………………………………59 Function Code Transmit………………………………………………………………………………………………60 Intercharacter, Interfunction, and Intermessage Delays………………………………………60
Intercharacter Delay ………………………………………………………………………………………………60 User Specified Intercharacter Delay……………………………………………………………………61 Interfunction Delay ………………………………………………………………………………………………..61 Intermessage Delay………………………………………………………………………………………………..62
Chapter 5 – Data Format ……………………………………………………………………. 63
Data Format Editor Introduction……………………………………………………………………………….63

Voyager 1350g User Guide

Show Data Format ………………………………………………………………………………………………………..64 Add a Data Format………………………………………………………………………………………………………..64
Other Programming Selections ……………………………………………………………………………65 Terminal ID Table …………………………………………………………………………………………………….66 Data Format Editor Commands …………………………………………………………………………………66 Send Commands …………………………………………………………………………………………………….66 Move Commands…………………………………………………………………………………………………….72 Search Commands………………………………………………………………………………………………….73 Miscellaneous Commands ……………………………………………………………………………………76 Data Formatter………………………………………………………………………………………………………………79 Data Format Non-Match Error Tone……………………………………………………………………80 Primary/Alternate Data Formats ……………………………………………………………………………….81 Single Scan Data Format Change………………………………………………………………………..81
Chapter 6 – Symbologies……………………………………………………………………..83
All Symbologies……………………………………………………………………………………………………………..84 Message Length Description ……………………………………………………………………………………..84 Codabar…………………………………………………………………………………………………………………………..84 Code 39 …………………………………………………………………………………………………………………………..87 Interleaved 2 of 5…………………………………………………………………………………………………………..90 NEC 2 of 5 ………………………………………………………………………………………………………………………91 Code 93 …………………………………………………………………………………………………………………………..93 Straight 2 of 5 Industrial (three-bar start/stop) ……………………………………………………..94 Straight 2 of 5 IATA (two-bar start/stop) ………………………………………………………………….95 Matrix 2 of 5 …………………………………………………………………………………………………………………..96 Code 11 …………………………………………………………………………………………………………………………..97 Code 128 ………………………………………………………………………………………………………………………..98
ISBT 128 Concatenation………………………………………………………………………………………..98 GS1-128 ………………………………………………………………………………………………………………………100 Telepen …………………………………………………………………………………………………………………………101 UPC-A …………………………………………………………………………………………………………………………..102 UPC-A/EAN-13 with Extended Coupon Code ……………………………………………………..105

Voyager 1350g User Guide

vii

Coupon GS1 DataBar Output …………………………………………………………………………………. 106 UPC-E0 ……………………………………………………………………………………………………………………….. 106 UPC-E1 ……………………………………………………………………………………………………………………….. 109 EAN/JAN-13 ………………………………………………………………………………………………………………. 109
ISBN Translate……………………………………………………………………………………………………… 116 EAN/JAN-8 …………………………………………………………………………………………………………………. 116 MSI……………………………………………………………………………………………………………………………….. 118 GS1 DataBar Omnidirectional………………………………………………………………………………… 120 GS1 DataBar Limited ……………………………………………………………………………………………….. 120 GS1 DataBar Expanded …………………………………………………………………………………………… 121 Trioptic Code………………………………………………………………………………………………………………. 121 Codablock A ……………………………………………………………………………………………………………….. 122 Codablock F ……………………………………………………………………………………………………………….. 123 Label Code………………………………………………………………………………………………………………….. 123 PDF417……………………………………………………………………………………………………………………….. 124 MacroPDF417……………………………………………………………………………………………………………. 124 MicroPDF417 …………………………………………………………………………………………………………….. 125 GS1 Composite Codes ……………………………………………………………………………………………… 126 GS1 Emulation…………………………………………………………………………………………………………… 127 TCIF Linked Code 39 (TLC39) ………………………………………………………………………………… 128 QR Code………………………………………………………………………………………………………………………. 128 DotCode………………………………………………………………………………………………………………………. 130 Digimarc BarcodeTM …………………………………………………………………………………………………… 131 Data Matrix…………………………………………………………………………………………………………………. 132 MaxiCode ……………………………………………………………………………………………………………………. 134 Aztec Code ………………………………………………………………………………………………………………….. 135 Chinese Sensible (Han Xin) Code ………………………………………………………………………….. 136 Postal Codes – 2D ……………………………………………………………………………………………………… 137
Planet Code Check Digit…………………………………………………………………………………….. 140 Postnet Check Digit…………………………………………………………………………………………….. 141 Australian Post Interpretation…………………………………………………………………………… 141

viii

Voyager 1350g User Guide

Postal Codes – Linear ………………………………………………………………………………………………..142 China Post (Hong Kong 2 of 5)…………………………………………………………………………..142 Korea Post………………………………………………………………………………………………………………143
Chapter 7 – Imaging Commands ………………………………………………………145
Single-Use Basis ………………………………………………………………………………………………………..145 Command Syntax……………………………………………………………………………………………………….145 Image Snap – IMGSNP………………………………………………………………………………………………146
IMGSNP Modifiers ……………………………………………………………………………………………….146 Image Ship – IMGSHP ……………………………………………………………………………………………….149
IMGSHP Modifiers ……………………………………………………………………………………………….150
Chapter 8 – Utilities………………………………………………………………………….. 159
To Add a Test Code I.D. Prefix to All Symbologies…………………………………………………159 Show Software Revision ……………………………………………………………………………………………159 Test Menu…………………………………………………………………………………………………………………….160 Application Plug-Ins (Apps)……………………………………………………………………………………..160 EZConfig for Scanning Introduction ………………………………………………………………………160
Configure with EZConfig for Scanning…………………………………………………………….161 Reset the Factory Defaults ……………………………………………………………………………………….161
Chapter 9 – Serial Programming Commands …………………………………..163
Conventions ………………………………………………………………………………………………………………..163 Menu Command Syntax……………………………………………………………………………………………163 Query Commands ………………………………………………………………………………………………………164 Trigger Commands…………………………………………………………………………………………………….166 Reset the Custom Defaults ………………………………………………………………………………………167 Menu Commands ………………………………………………………………………………………………………168
Chapter 10 – Security ……………………………………………………………………….191
System Architecture…………………………………………………………………………………………………..191 Connect with USB…………………………………………………………………………………………………191 Connect with RS232 Serial Port ……………………………………………………………………….192

Voyager 1350g User Guide

Security Checklist ……………………………………………………………………………………………………… 192 Infection by Malicious Software Agents …………………………………………………………. 192
Unauthorized External Access ……………………………………………………………………………….. 192 Unauthorized Internal Access …………………………………………………………………………… 193 Securing barcode scanner series……………………………………………………………………… 193
Security Updates and Service Packs……………………………………………………………………… 194 Additional Resources ……………………………………………………………………………………………….. 194
Chapter 11 – Product Specifications ………………………………………………..195
Voyager 1350g Scanner Product Specifications ………………………………………………… 195 Depth of Field Charts ……………………………………………………………………………………………….. 196
Typical Performance …………………………………………………………………………………………… 196 Guaranteed Performance ………………………………………………………………………………….. 196 Standard Connector Pinouts ………………………………………………………………………………….. 197 Serial Output ………………………………………………………………………………………………………… 197 USB ………………………………………………………………………………………………………………………… 198 Required Safety Labels ……………………………………………………………………………………………. 198
Chapter 12 – Maintenance and Troubleshooting …………………………….199
Repairs ………………………………………………………………………………………………………………………… 199 Maintenance………………………………………………………………………………………………………………. 199
Clean the Scanner……………………………………………………………………………………………….. 199 Inspect Cords and Connectors …………………………………………………………………………. 200 Replace Cable…………………………………………………………………………………………………………….. 200 Replace an Interface Cable ……………………………………………………………………………….. 200 Troubleshoot………………………………………………………………………………………………………………. 200
Chapter A – Reference Charts …………………………………………………………..203
Symbology Charts …………………………………………………………………………………………………….. 203 Linear Symbologies…………………………………………………………………………………………….. 203 2D Symbologies…………………………………………………………………………………………………… 204 Postal Symbologies …………………………………………………………………………………………….. 205
ASCII Conversion Chart (Code Page 1252)………………………………………………………….. 206

Voyager 1350g User Guide

Lower ASCII Reference Table……………………………………………………………………………………207 ISO 2022/ISO 646 Character Replacements ……………………………………………………….210 Keyboard Key References………………………………………………………………………………………….212
Sample Symbols……………………………………………………………………………….. 213
Programming Chart ………………………………………………………………………….215

Voyager 1350g User Guide

xii

Voyager 1350g User Guide

Customer Support
Technical Assistance
To search our knowledge base for a solution or to log in to the Technical Support portal and report a problem, go to www.honeywellaidc.com/working-with- us/contact-technical-support. For our latest contact information, see www.honeywellaidc.com/locations.
Product Service and Repair
Honeywell International Inc. provides service for all of its products through service centers throughout the world. To obtain warranty or non-warranty service, return your product to Honeywell (postage paid) with a copy of the dated purchase record. To learn more, go to www.honeywellaidc.com and select Service & Repair at the bottom of the page.
Limited Warranty
For warranty information, go to www.honeywellaidc.com and click Resources > Product Warranty.

Voyager 1350g User Guide

xiii

xiv

Voyager 1350g User Guide

CHAPTER
1 GET STARTED
About This Manual
This User Guide provides installation and programming instructions for the Voyager XP 1350g corded area-imaging scanner. Product specifications, dimensions, warranty, and customer support information are also included. Honeywell barcode scanners are factory programmed for the most common terminal and communications settings. If you need to change these settings, programming is accomplished by scanning the barcodes in this guide. An asterisk (*) next to an option indicates the default setting.
Unpack Your Device
After you open the shipping carton containing the product, take the following steps: · Check for damage during shipment. Report damage immediately to the carrier
who delivered the carton. · Make sure the items in the carton match your order. · Save the shipping container for later storage or shipping.

Voyager 1350g User Guide

Connect the Device
Connect with USB
A scanner can be connected to the USB port of a computer. 1. Connect the appropriate interface cable to the device first, then to the
computer.
Voyager 1350g USB Connection:
2. The scanner beeps. 3. Verify the scanner operation by scanning a barcode from the Sample Symbols,
beginning on page 213. The unit defaults to a USB PC Keyboard. Refer to page 8 for other USB terminal settings. For additional USB programming and technical information, refer to “USB Application Note,” available at www.honeywellaidc.com.

Voyager 1350g User Guide

Connect with RS232 Serial Port
1. Turn off power to the terminal/computer. 2. Connect the appropriate interface cable to the scanner.
Note: For the scanner to work properly, you must have the correct cable for your type of terminal/computer.
Voyager 1350g Scanner RS232 Serial Port Connection:

Note: The power supply must be ordered separately, if needed.
3. Plug the serial connector into the serial port on your computer. Tighten the two screws to secure the connector to the port.
4. Once the scanner has been fully connected, power up the computer. This interface programs 115,200 baud, 8 data bits, no parity, and 1 stop bit.
Reading Techniques
The view finder projects an aiming dot that should be centered over the barcode, but it can be positioned in any direction for a good read. Hold the scanner over the barcode, press the button, and center the aiming dot on the barcode.

Voyager 1350g User Guide

The aiming dot is smaller when the scanner is closer to the code and larger when it is farther from the code. Hold the scanner close to smaller bar codes, and farther away from large bar codes to get a proper read.
Troubleshooting
· If the light level in the room is not high enough, the barcode may not be read. · If the barcode is highly reflective (e.g., laminated), you may need to tilt the
scanner at an angle so the barcode can be scanned.
Menu Barcode Security Settings
Honeywell scanners are programmed by scanning menu barcodes or by sending serial commands to the scanner. If you want to restrict the ability to scan menu codes, you can use the Menu Barcode Security settings. Contact the nearest technical support office (see Technical Assistance on page xiii) for further information.
Set Custom Defaults
You have the ability to create a set of menu commands as your own, custom defaults. To do so, scan the Set Custom Defaults barcode below before scanning the menu commands for your custom defaults. If a menu command requires scanning numeric codes from the Programming Chart, beginning on page 215, then a Save code, that entire sequence will be saved to your custom defaults. When you have entered all the commands you want to save for your custom defaults, scan the Save Custom Defaults barcode.
Set Custom Defaults
Save Custom Defaults
You may have a series of custom settings and want to correct a single setting. To do so, just scan the new setting to overwrite the old one. For example, if you had previously saved the setting for Beeper Volume at Low to your custom defaults, and decide you want the beeper volume set to High, just scan the Set Custom Defaults barcode, then scan the Beeper Volume High menu code, and then Save Custom Defaults. The rest of the custom defaults will remain, but the beeper volume setting will be updated.

Voyager 1350g User Guide

Reset the Custom Defaults
If you want the custom default settings restored to your scanner, scan the Activate Custom Defaults barcode below. This is the recommended default barcode for most users. It resets the scanner to the custom default settings. If there are no custom defaults, it will reset the scanner to the factory default settings. Any settings that have not been specified through the custom defaults will be defaulted to the factory default settings.
Activate Custom Defaults

Voyager 1350g User Guide

CHAPTER
2 PROGRAM THE INTERFACE

Introduction
This chapter describes how to program your system for the desired interface.

Program the Interface – Plug and Play
Plug and Play barcodes provide instant scanner set up for commonly used interfaces.
Note: After you scan one of the codes, power cycle the host terminal to have the interface in effect.

RS232 Serial Port

The RS232 Interface barcode is used when connecting to the serial port of a PC or terminal. The following RS232 Interface barcode also programs a carriage return (CR) and a line feed (LF) suffix, baud rate, and data format as indicated below. It also changes the trigger mode to manual.

Option Baud Rate Data Format

Setting 115,200 bps 8 data bits, no parity bit, 1 stop bit

RS232 Interface

Voyager 1350g User Guide

USB IBM SurePos
Scan one of the following “Plug and Play” codes to program the scanner for an IBM SurePos (USB handheld scanner) or IBM SurePos (USB tabletop scanner) interface.
Note: After scanning one of these codes, you must power cycle the cash register.

USB IBM SurePos (USB Handheld Scanner)
Interface

USB IBM SurePos (USB Tabletop Scanner)
Interface

Each barcode above also programs the following suffixes for each symbology:

Symbology EAN 8 EAN 13 UPC A UPC E

Suffix 0C 16 0D 0A

Symbology Code 39 Interleaved 2 of 5 Code 128 Code 39

Suffix 00 0A 0B 00 0D 0B 00 18 0B 00 0A 0B

USB PC or Macintosh Keyboard
Scan one of the following codes to program the scanner for USB PC Keyboard or USB Macintosh Keyboard. Scanning these codes also adds a CR suffix.

USB Keyboard (PC) USB Japanese Keyboard (PC)

USB Keyboard (Mac)

Voyager 1350g User Guide

USB HID
Scan the following code to program the scanner for USB HID Barcode scanners.
USB HID Barcode Scanner
USB Serial
If you are using a Microsoft® Windows® PC, you will need to download the latest driver from the Honeywell website (www.honeywellaidc.com). The driver will use the next available COM Port number. Apple® Macintosh computers recognize the scanner as a USB CDC class device and automatically use a class driver. After the driver is downloaded, scan the following code to program the scanner to emulate a regular RS232-based COM Port.
USB Serial
No extra configuration (e.g., baud rate) is necessary. Note: If you scan the USB Serial barcode either with an older Honeywell serial driver, or no
driver installed, you may no longer be able to scan barcodes. If this happens, either uninstall the older driver versions and install the latest driver, or delete the specific device entry in Device Manager.
CTS/RTS Emulation

CTS/RTS Emulation On
ACK/NAK Mode

CTS/RTS Emulation Off

ACK/NAK Mode On

Voyager 1350g User Guide

ACK/NAK Mode Off
Secondary Interface for USB
When using a USB interface, you may wish to configure your scanner to communicate with scanner management software. Scan the Secondary Interface On barcode to communicate with the scanner management software. To disable this capability, scan Secondary Interface Off. Default = Secondary Interface On.
Secondary Interface Off
Secondary Interface On
Keyboard Country Layout
If your interface is USB Keyboard or Keyboard Wedge, your keyboard layout default is a US keyboard. To change this layout, scan the appropriate Keyboard Country barcode below. By default, national character replacements are used for the following characters: # $ @ [ ] ^ ` { | } ~. Refer to the “ISO 2022/ISO 646 Character Replacements” on page 210 to view the character replacements for each country.
Keyboard Countries
United States
Albania
Azeri (Cyrillic)
Azeri (Latin)

Voyager 1350g User Guide

Keyboard Countries (Continued)
Belarus Bosnia Brazil (MS) Bulgaria (Latin) Canada (French) Croatia
Voyager 1350g User Guide

Belgium Brazil Bulgaria (Cyrillic) Canada (French legacy) Canada (Multilingual) Czech
11

Keyboard Countries (Continued)
Czech (Programmers) Czech (QWERTZ)
Dutch (Netherlands) Faroese France
Germany
12

Czech (QWERTY) Denmark Estonia Finland Gaelic Greek
Voyager 1350g User Guide

Keyboard Countries (Continued)
Greek (220 Latin) Greek (319 Latin)
Greek (Latin) Greek (Polytonic) Hungarian (101 key)
Iceland
Voyager 1350g User Guide

Greek (220) Greek (319) Greek (MS)
Hebrew Hungary
Irish
13

Keyboard Countries (Continued)
Italian (142) Japan ASCII Kyrgyz (Cyrillic)
Latvia Lithuania Macedonia
14

Italy Kazakh Latin America Latvia (QWERTY) Lithuania (IBM) Malta
Voyager 1350g User Guide

Keyboard Countries (Continued)
Mongolian (Cyrillic) Poland
Polish (Programmers) Romania
Russian (MS) SCS
Voyager 1350g User Guide

Norway Polish (214)
Portugal Russia
Russian (Typewriter) Serbia (Cyrillic)
15

Keyboard Countries (Continued)
Serbia (Latin) Slovakia (QWERTY)
Slovenia Spanish variation Switzerland (French)
Tatar
16

Slovakia Slovakia (QWERTZ)
Spain Sweden Switzerland (German) Turkey F
Voyager 1350g User Guide

Keyboard Countries (Continued)
Turkey Q
Ukrainian
United Kingdom
United States (Dvorak)
United States (Dvorak left)
United States (Dvorak right)
United States (International)
Uzbek (Cyrillic)
Keyboard Wedge Modifiers
ALT Mode
If your barcode contains special characters from the extended ASCII chart, for example, an e with an accent grave (è), you will use ALT Mode. (See Extended ASCII Characters on page 207.) Note: Scan the ALT mode barcode after scanning the appropriate Keyboard Country code.

Voyager 1350g User Guide

If your keystrokes require the ALT key and 3 or 4 characters, scan the 3 Characters or 4 Characters barcode. The data is then output with the special character(s) for values 00-255. Default = Off.

Off
3 Characters
4 Characters
Keyboard Style
This programs keyboard styles, such as Caps Lock and Shift Lock. If you have used Keyboard Conversion settings, they will override any of the following Keyboard Style settings. Default = Regular. Regular is used when you normally have the Caps Lock key off.
Regular
Caps Lock is used when you normally have the Caps Lock key on.
Caps Lock
Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards).
Shift Lock

Voyager 1350g User Guide

Keyboard Conversion
Alphabetic keyboard characters can be forced to be all upper case or all lowercase. So if you have the following barcode: “abc569GK,” you can make the output “ABC569GK” by scanning Convert All Characters to Upper Case, or to “abc569gk” by scanning Convert All Characters to Lower Case.
These settings override Keyboard Style selections.
Default = Keyboard Conversion Off.

Keyboard Conversion Off

Convert All Characters to Upper Case

Convert All Characters to Lower Case
Control Character Output
This selection sends a text string instead of a control character. For example, when the control character for a carriage return is expected, the output would display [CR] instead of the ASCII code of 0D. Refer to ASCII Conversion Chart (Code Page 1252) on page 206. Only codes 00 through 1F are converted (the first column of the chart). Default = Off.
Note: Control + X (Control + ASCII) Mode overrides this mode.

Control Character Output On

Control Character Output Off

Voyager 1350g User Guide

Keyboard Modifiers
This modifies special keyboard features, such as CTRL+ ASCII codes and Turbo Mode.
Control + X (Control + ASCII) Mode On: The scanner sends key combinations for ASCII control characters for values 00-1F. Windows is the preferred mode. All keyboard country codes are supported. DOS mode is a legacy mode, and it does not support all keyboard country codes. New users should use the Windows mode. Refer to ASCII Conversion Chart (Code Page 1252), page 206 for CTRL+ X Values.
Windows Mode Prefix/Suffix Off: The scanner sends key combinations for ASCII control characters for values 00-1F, but it does not translate prefix or suffix information.
Support ALT 3 Digit HEX Mode: The scanner sends key combinations for ASCII control characters for values 00-1F transmitted as the ALT key and 3 digits.
Default = Control + X Mode Off.

Windows Mode Control + X Mode On
DOS Mode Control + X Mode On
DOS Mode Control + X Mode On with Windows Mode Prefix/Suffix

Control + X Mode Off Windows Mode Prefix/Suffix Supports ALT 3 Digit HEX Mode

Voyager 1350g User Guide

Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode. Default = Off.

Turbo Mode On

Turbo Mode Off
Numeric Keypad Mode: Sends numeric characters as if entered from a numeric keypad. Default = Off.

Numeric Keypad Mode On

Numeric Keypad Mode Off
RS232 Modifiers
RS232 Baud Rate
Baud Rate sends the data from the scanner to the terminal at the specified rate. The host terminal must be set for the same baud rate as the scanner. Default = 115,200.

300 1200
Voyager 1350g User Guide

600
2400
21

4800
9600
19200
38400
57,600

115,200
RS232 Word Length: Data Bits, Stop Bits, and Parity
Data Bits sets the word length at 7 or 8 bits of data per character. If an application requires only ASCII Hex characters 0 through 7F decimal (text, digits, and punctuation), select 7 data bits. For applications that require use of the full ASCII set, select 8 data bits per character. Default = 8. Stop Bits sets the stop bits at 1 or 2. Default = 1. Parity provides a means of checking character bit patterns for validity. Default = None.

7 Data, 1 Stop, Parity Even 7 Data, 1 Stop, Parity Odd

7 Data, 1 Stop, Parity None

Voyager 1350g User Guide

7 Data, 2 Stop, Parity None

7 Data, 2 Stop, Parity Even 7 Data, 2 Stop, Parity Odd

8 Data, 1 Stop, Parity Even

8 Data, 1 Stop, Parity None

8 Data, 1 Stop, Parity Odd
8 Data, 1 Stop, Parity Mark
RS232 Receiver Time-Out
The unit stays awake to receive data until the RS232 Receiver Time-Out expires. A manual or serial trigger resets the time-out. When an RS232 receiver is sleeping, a character may be sent to wake up the receiver and reset the time-out. A transaction on the CTS line will also wake up the receiver. The receiver takes 300 milliseconds to completely come up. Change the RS232 receiver time-out by scanning the barcode below, then scanning digits from the Programming Chart, beginning on page 215, then scanning Save. The range is 0 to 300 seconds. Default = 0 seconds (no time-out – always on).

RS232 Receiver Time-Out

Voyager 1350g User Guide

RS232 Handshake
RS232 Handshaking allows control of data transmission from the scanner using software commands from the host device. When RTS/CTS is turned Off, no data flow control is used. Flow Control, No Timeout: The scanner asserts RTS when it has data to send, and will wait indefinitely for CTS to be asserted by the host. Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS when it is OK for the device to transmit. Flow Control with Timeout: The scanner asserts RTS when it has data to send and waits for a delay (see RS232 Timeout on page 24) for CTS to be asserted by the host. If the delay time expires and CTS is not asserted, the device transmit buffer is cleared and scanning may resume. Default = RTS/CTS Off.
Flow Control, No Timeout
Two-Direction Flow Control
Flow Control with Timeout

RTS/CTS Off
RS232 Timeout
When using Flow Control with Timeout, you must program the length of the delay you want to wait for CTS from the host. Set the length (in milliseconds) for a timeout by scanning the barcode below, then setting the timeout (from 1-5100 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then scanning Save.
RS232 Timeout

Voyager 1350g User Guide

XON/XOFF
Standard ASCII control characters can be used to tell the scanner to start sending data (XON/XOFF On) or to stop sending data (XON/XOFF Off). When the host sends the XOFF character (DC3, hex 13) to the scanner, data transmission stops. To resume transmission, the host sends the XON character (DC1, hex 11). Data transmission continues where it left off when XOFF was sent. Default = XON/XOFF Off.

XON/XOFF On

XON/XOFF Off
ACK/NAK
After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15) response from the host. If ACK is received, the communications cycle is completed and the scanner looks for more barcodes. If NAK is received, the last set of barcode data is retransmitted and the scanner waits for ACK/NAK again. Turn on the ACK/NAK protocol by scanning the ACK/NAK On barcode below. To turn off the protocol, scan ACK/NAK Off. Default = ACK/NAK Off.

ACK/NAK On

ACK/NAK Off

Voyager 1350g User Guide

CHAPTER
3 INPUT/OUTPUT SETTINGS

Power Up Beeper
The scanner can be programmed to beep when it’s powered up. Scan the Off barcode(s) if you don’t want a power up beep. Default = Power Up Beeper On Scanner.

Power Up Beeper Off Scanner

Power Up Beeper On Scanner
Beep on BEL Character
You may wish to force the scanner to beep upon a command sent from the host. If you scan the Beep on BEL On barcode below, the scanner will beep every time a BEL character is received from the host. Default = Beep on BEL Off.

*Beep on BEL Off

Beep on BEL On

Voyager 1350g User Guide

Trigger Click
To hear an audible click every time the scanner trigger is pressed, scan the Trigger Click On barcode below. Scan the Trigger Click Off code if you don’t wish to hear the click. (This feature has no effect on serial or automatic triggering.) Default = Trigger Click Off.

*Trigger Click Off
Trigger Click On
Good Read and Error Indicators
Beeper Good Read
The beeper may be programmed On or Off in response to a good read. Turning this option off only turns off the beeper response to a good read indication. All error and menu beeps are still audible. Default = Beeper – Good Read On.

Beeper – Good Read Off

Beeper – Good Read On
Beeper Volume Good Read
The beeper volume codes modify the volume of the beep the scanner emits on a good read. Default = High.

Low

Medium

Voyager 1350g User Guide

High
Off
Beeper Pitch Good Read
The beeper pitch codes modify the pitch (frequency) of the beep the scanner emits on a good read. Default = Medium.

Low (1600 Hz)

Medium (2700 Hz)

High (4200 Hz)
Beeper Pitch Error
The beeper pitch codes modify the pitch (frequency) of the sound the scanner emits when there is a bad read or error. Default = Razz.

Razz (250 Hz) High (4200 Hz)

Medium (3250 Hz)

Voyager 1350g User Guide

Beeper Duration Good Read
The beeper duration codes modify the length of the beep the scanner emits on a good read. Default = Normal.

Normal Beep
Short Beep
LED Good Read
The LED indicator can be programmed On or Off in response to a good read. Default = On.
LED – Good Read On
LED – Good Read Off
Number of Beeps Good Read
The number of beeps of a good read can be programmed from 1 – 9. The same number of beeps will be applied to the beeper and LED in response to a good read. For example, if you program this option to have five beeps, there will be five beeps and five LED flashes in response to a good read. The beeps and LED flashes are in sync with one another. To change the number of beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 215, then Save. Default = 1.
Number of Good Read Beeps/LED Flashes
Number of Beeps Error
The number of beeps and LED flashes emitted by the scanner for a bad read or error can be programmed from 1 – 9. For example, if you program this option to have five error beeps, there will be five error beeps and five LED flashes in response

Voyager 1350g User Guide

to an error. To change the number of error beeps, scan the barcode below and then scan a digit (1-9) barcode from the Programming Chart, beginning on page 215, then Save. Default = 1.
Number of Error Beeps/LED Flashes
Good Read Delay
This sets the minimum amount of time before the scanner can read another barcode. Default = 0 ms (No Delay).

No Delay
Short Delay (500 ms)
Medium Delay (1,000 ms)
Long Delay (1,500 ms)
User-Specified Good Read Delay
If you want to set your own length for the good read delay, scan the barcode below, then set the delay (from 0 – 30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then Save.
User-Specified Good Read Delay

Voyager 1350g User Guide

Trigger Modes
Manual Trigger
In manual trigger mode, the scanner scans until a barcode is read, or until the scan trigger is released. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don’t require a long working range. Default = Manual Trigger Normal.
*Manual Trigger – Normal
Manual Trigger Enhanced
Serial Trigger
You can activate the scanner either by pressing the trigger, or using a serial trigger command (see Trigger Commands on page 166). You must be in a serial interface mode in order to use serial triggering. Refer to RS232 Serial Port (page 7) or USB Serial (page 9) for further information. When in serial mode, the scanner scans until a barcode has been read or until the deactivate command is sent. The scanner can also be set to turn itself off after a specified time has elapsed (see Read TimeOut, which follows).
Read Time-Out
Use this selection to set a time-out (in milliseconds) of the scanner’s trigger when using serial commands to trigger the scanner. Once the scanner has timed out, you can activate the scanner either by pressing the trigger or using a serial trigger command. After scanning the Read Time-Out barcode, set the time-out duration (from 0-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then Save. Default = 30,000 ms.
Read Time-Out

Voyager 1350g User Guide

Presentation Mode
Presentation Mode uses ambient light and scanner illumination to detect barcodes. When in Presentation Mode, the LEDs remain dim until a barcode is presented to the scanner, then the aimer turns on and the LEDs turn up to read the code. If the light level in the room is not high enough, Presentation Mode may not work properly.
Scan the following barcode to program your scanner for Presentation Mode.

Presentation Mode
Presentation LED Behavior after Decode
When a scanner is in presentation mode, the LED aimer dims 30 seconds after a barcode is decoded. If you wish to dim the LED aimer immediately after a barcode is decoded, scan the LEDs Off barcode, below. Default = LEDs On.

LEDs On

LEDs Off
Presentation Centering
Use Presentation Centering to narrow the scanner’s field of view when it is in the stand to make sure the scanner reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, Presentation Centering will ensure that only the desired codes are read.
Note: To adjust centering when the scanner is hand-held, see Centering (page 3-42).
If a barcode is not touched by a predefined window, it will not be decoded or output by the scanner. If Presentation Centering is turned on by scanning Presentation Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Presentation Centering Window, Bottom of Presentation Centering Window, Left, and Right of Presentation Centering Window barcodes.
In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.

Voyager 1350g User Guide

0% Barcode 1
10

Barcode 2

100 0

10 20 30 40 50 60 70 80 90 100%

Note: A barcode needs only to be touched by the centering window in order to be read. It does not need to pass completely through the centering window.
Scan Presentation Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window from the Programming Chart, beginning on page 215, then Save. Default Presentation Centering = 40% for Top and Left, 60% for Bottom and Right.

Presentation Centering On
Top of Presentation Centering Window

Presentation Centering Off
Bottom of Presentation Centering Window

Voyager 1350g User Guide

Left of Presentation Centering
Window
Right of Presentation Centering Window
In-Stand Sensor Mode
This feature senses when the scanner is removed from the stand and tells it to begin manual triggering. When Sensor On is enabled, the scanner defaults to Presentation Mode when it is in the stand, and to Manual Trigger Mode when it is removed from the stand. Default = Sensor On.

*Sensor On
Sensor Off
Poor Quality Codes
Poor Quality 1D Codes
This setting improves the scanner’s ability to read damaged or badly printed linear barcodes. When Poor Quality 1D Reading On is scanned, poor quality linear barcode reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality barcodes. This setting does not affect 2D barcode reading. Default = Poor Quality 1D Reading Off.

Poor Quality 1D Reading On
Voyager 1350g User Guide

Poor Quality 1D Reading Off
35

Poor Quality PDF Codes
This setting improves the scanner’s ability to read damaged or badly printed PDF codes by combining information from multiple images. It is useful when a complete barcode cannot be seen in one image. This setting does not affect 1D barcode reading. Default = Poor Quality PDF Reading Off.
Poor Quality PDF Reading On
*Poor Quality PDF Reading Off
Low Resolution PDF Codes
This setting improves the scanner’s ability to read low resolution PDF codes. When Low Resolution PDF Codes On is scanned, poor quality PDF code reading is improved, but the scanner’s snappiness is decreased, making it less aggressive when reading good quality barcodes. This setting does not affect 1D barcode reading. Default = Low Resolution PDF Codes Off.
Low Resolution PDF Codes On

Low Resolution PDF Codes Off
CodeGateTM
When CodeGate is On, the trigger is used to allow decoded data to be transmitted to the host system. The scanner remains on, scanning and decoding barcodes, but the barcode data is not transmitted until the trigger is pressed. When CodeGate is Off, barcode data is transmitted when it is decoded. Default = CodeGate Off Out-ofStand.
CodeGate Off Out-of-Stand

Voyager 1350g User Guide

CodeGate On Out-of-Stand
Streaming Presentation Mode
When in Streaming Presentation mode, the scanner’s aimer goes out after a short time, but the scan illumination remains on all the time to continuously search for barcodes. Two modes are available, Normal and Enhanced. Normal mode offers good scan speed and the longest working ranges (depth of field). Enhanced mode will give you the highest possible scan speed but slightly less range than Normal mode. Enhanced mode is best used when you require a very fast scan speed and don’t require a long working range.

Streaming Presentation Mode – Normal
Streaming Presentation Mode – Enhanced
When using Preferred Symbology (see page 44), a lower priority symbol must be centered on the aiming pattern to be read in Streaming Presentation Mode.
Note: When the scanner is placed in a stand, it will revert to Presentation Mode (see page 33).
Hands Free Time-Out
The Scan Stand and Presentation Modes are referred to as “hands free” modes. If the scanner’s trigger is pulled when using a hands free mode, the scanner changes to manual trigger mode. You can set the time the scanner should remain in manual trigger mode by setting the Hands Free Time-Out. Once the time-out value is reached, (if there have been no further trigger pulls) the scanner reverts to the original hands free mode. Scan the Hands Free Time-Out barcode, then scan the time-out duration (from 0300,000 milliseconds) from the Programming Chart, beginning on page 215, then Save. Default = 5,000 ms.

Hands Free Time-Out

Voyager 1350g User Guide

Reread Delay
This sets the time period before the scanner can read the same barcode a second time. Setting a reread delay protects against accidental rereads of the same barcode. Longer delays are effective in minimizing accidental rereads. Use shorter delays in applications where repetitive barcode scanning is required. Reread Delay only works when in a Presentation Mode (see page 33). Default = Medium.
Short (500 ms)

Medium (750 ms)
Long (1000 ms)
Extra Long (2000 ms)
User-Specified Reread Delay
If you want to set your own length for the reread delay, scan the barcode below, then set the delay (from 0-30,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then Save.
User-Specified Reread Delay
2D Reread Delay
Sometimes 2D barcodes can take longer to read than other barcodes. If you wish to set a separate Reread Delay for 2D barcodes, scan one of the programming codes that follows. 2D Reread Delay Off indicates that the time set for Reread Delay is used for both 1D and 2D barcodes. Default = 2D Reread Delay Off.
2D Reread Delay Off

Voyager 1350g User Guide

Medium (2000ms)

Short (1000ms)

Long (3000ms)

Extra Long (4000ms)
Character Activation
You may use a character sent from the host to trigger the scanner to begin scanning. When the activation character is received, the scanner continues scanning until either the Character Activation Timeout (page 3-40) is reached, the deactivation character is received (see Deactivation Character on page 41), or a barcode is transmitted. Scan the On barcode to use character activation, then use Activation Character (page 39) to select the character you will send from the host to start scanning. Default = Off.

On
Activation Character
This sets the character used to trigger scanning when using Character Activation Mode. On the ASCII Conversion Chart (Code Page 1252), page 206, find the hex value that represents the character you want to use to trigger scanning. Scan the following barcode, then use the Programming Chart to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Default = 12 [DC2].

Activation Character

Voyager 1350g User Guide

End Character Activation After Good Read
After a barcode is successfully detected and read from the scanner, the illumination can be programmed either to remain on and scanning, or to turn off. When End Character Activation After Good Read is enabled, the illumination turns off and stops scanning after a good read. If you scan Do Not End Character Activation After Good Read, the illumination remains on after a good read.
Do Not End Character Activation After Good Read
End Character Activation After Good Read
Character Activation Timeout
You can set a timeout for the length of time the illumination remains on and attempting to decode barcodes when using Character Activation Mode. Set the length (in milliseconds) for a timeout by scanning the following barcode, then setting the timeout (from 1-300,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then Save. Default = 30,000 ms.
Character Activation Timeout
Character Deactivation
If you have sent a character from the host to trigger the scanner to begin scanning, you can also send a deactivation character to stop scanning. Scan the following On barcode to use character deactivation, then use Deactivation Character (following) to select the character you will send from the host to terminate scanning. Default = Off.

Off
On

Voyager 1350g User Guide

Deactivation Character
This sets the character used to terminate scanning when using Character Deactivation Mode. On the ASCII Conversion Chart (Code Page 1252), page 206, find the hex value that represents the character you want to use to terminate scanning. Scan the following barcode, then use the Programming Chart, beginning on page 215 to read the alphanumeric combination that represents that ASCII character. Scan Save to finish. Default = 14 [DC4].
Deactivation Character
Illumination Lights
If you want the illumination lights on while reading a barcode, scan the Lights On barcode, below. However, if you want to turn just the lights off, scan the Lights Off barcode. Default = Lights On. Note: This setting does not affect the aimer light. The aiming light can be set using Aimer Mode (page 42).

Lights On
Lights Off
Aimer Delay
The aimer delay allows a delay time for the operator to aim the scanner before the picture is taken. Use these codes to set the time between when the trigger is pulled and when the picture is taken. During the delay time, the aiming light will appear, but the LEDs won’t turn on until the delay time is over. Default = Off.
1 millisecond
250 milliseconds

Voyager 1350g User Guide

500 milliseconds

Off (no
User-Specified Aimer Delay
If you want to set your own length for the duration of the delay, scan the barcode below, then set the time-out by scanning digits (0 – 4,000 ms) from the Programming Chart, beginning on page 215, then Save.
Delay Duration
Aimer Mode
This feature allows you to turn the aimer on and off. Default = On
Off
*On
Centering
Use Centering to narrow the scanner’s field of view to make sure that when the scanner is hand-held, it reads only those barcodes intended by the user. For instance, if multiple codes are placed closely together, centering will insure that only the desired codes are read. (Centering can be used in conjunction with Aimer Delay, page 41, for the most error-free operation in applications where multiple codes are spaced closely together. Using the Aimer Delay and Centering features, the scanner can emulate the operation of older systems, such as linear laser barcode scanners.) Note: To adjust centering when the scanner is in a stand, see Presentation Centering (page 3-33).

Voyager 1350g User Guide

Single Code Centering
Scan Single Code Centering to target the barcode closest to the center of the image. Singling out a barcode in this manner increases scanning accuracy when there are multiple barcodes close together.

Single Code Centering

Custom Centering
Use the following settings to customize your centering window. If a barcode is not touched by a predefined window, it will not be decoded or output by the scanner. If centering is turned on by scanning Centering On, the scanner only reads codes that pass through the centering window you specify using the Top of Centering Window, Bottom of Centering Window, Left, and Right of Centering Window barcodes.
Example: In the example below, the white box is the centering window. The centering window has been set to 20% left, 30% right, 8% top, and 25% bottom. Since Barcode 1 passes through the centering window, it will be read. Barcode 2 does not pass through the centering window, so it will not be read.

0% Barcode 1
10 20

Barcode 2

100 0

10 20 30 40 50 60 70 80 90 100%

Note: A barcode needs only to be touched by the centering window in order to be read. It

Voyager 1350g User Guide

does not need to pass completely through the centering window.
Scan Centering On, then scan one of the following barcodes to change the top, bottom, left, or right of the centering window. Then scan the percent you want to shift the centering window using digits from the Programming Chart, beginning on page 215, then Save. Default Centering = 40% for Top and Left, 60% for Bottom and Right.

Centering On Top of Centering Window

Centering Off

Bottom of Centering Window

Left of Centering Window

Right of Centering Window
Preferred Symbology
The scanner can be programmed to specify one symbology as a higher priority over other symbologies in situations where both barcode symbologies appear on the same label, but the lower priority symbology cannot be disabled.
For example, you may be using the scanner in a retail setting to read U.P.C. symbols, but have occasional need to read a code on a driver’s license. Since some licenses have a Code 39 symbol as well as the PDF417 symbol, you can use Preferred Symbology to specify that the PDF417 symbol be read instead of the Code 39.
Preferred Symbology classifies each symbology as high priority, low priority, or as an unspecified type. When a low priority symbology is presented, the scanner ignores it for a set period of time (see Preferred Symbology Time-out on page 46) while it searches for the high priority symbology. If a high priority symbology is located during this period, then that data is read immediately.

Voyager 1350g User Guide

If the time-out period expires before a high priority symbology is read, the scanner will read any barcode in its view (low priority or unspecified). If there is no barcode in the scanner’s view after the time-out period expires, then no data is reported. Note: A low priority symbol must be centered on the aiming pattern to be read. Scan a barcode below to enable or disable Preferred Symbology. Default = Preferred Symbology Off.
Preferred Symbology On

Preferred Symbology Off
High Priority Symbology
To specify the high priority symbology, scan the High Priority Symbology barcode below. On the Symbology Charts on page 203, find the symbology you want to set as high priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 215, then Save. Default = None.
High Priority Symbology
Low Priority Symbology
To specify the low priority symbology, scan the Low Priority Symbology barcode below. On the Symbology Charts on page 203, find the symbology you want to set as low priority. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 215. If you want to set additional low priority symbologies, scan FF, then scan the 2 digit hex value from the Programming Chart, beginning on page 215, for the next symbology. You can program up to 5 low priority symbologies. Scan Save to save your selection. Default = None.
Low Priority Symbology

Voyager 1350g User Guide

Preferred Symbology Time-out
Once you have enabled Preferred Symbology and entered the high and low priority symbologies, you must set the time-out period. This is the period of time the scanner will search for a high priority barcode after a low priority barcode has been encountered. Scan the barcode below, then set the delay (from 1-3,000 milliseconds) by scanning digits from the Programming Chart, beginning on page 215, then Save. Default = 500 ms.
Preferred Symbology Time-out
Preferred Symbology Default
Scan the barcode below to set all Preferred Symbology entries to their default values.
Preferred Symbology Default
Output Sequence Overview
Output Sequence Editor
This programming selection allows you to program the scanner to output data (when scanning more than one symbol) in whatever order your application requires, regardless of the order in which the barcodes are scanned. You can define up to 15 barcodes in an output sequence.
Note: To make Output Sequence Editor selections, you’ll need to know the code I.D., code length, and character match(es) your application requires. Use the alphanumeric symbols from the Programming Chart, beginning on page 215. You must hold the trigger while reading each barcode in the sequence.
To Add an Output Sequence
An output sequence is created using a string of serial commands that is sent to the scanner. This string is most easily sent to the scanner using the EZConfig software tool (see EZConfig for Scanning Introduction on page 160). You can also accomplish this by scanning alphanumeric barcodes (see the Programming Chart, beginning on page 215).

Voyager 1350g User Guide

1. If you are using barcodes to create your output sequence, scan Enter Output Sequence on page 50.
2. Code I.D. On the Symbology Charts on page 203, find the symbology to which you want to apply the output sequence format. Make a note of the hex value for that symbology. If you are using barcodes to create your output sequence, scan the 2 digit hex value from the Programming Chart, beginning on page 215.
3. Length Specify what length (up to 9999 characters) of data output will be acceptable for this symbology. Make a note of the length. If you are using barcodes to create your output sequence, scan the 4 digit data length Programming Chart, beginning on page 215. (Note: 50 characters is entered as 0050. 9999 is a universal number, indicating all lengths.) When calculating the length, you must count any programmed prefixes, suffixes, or formatted characters as part of the length (unless using 9999).
4. Character Match Sequences On the ASCII Conversion Chart (Code Page 1252), page 206, find the hex value that represents the character(s) you want to match. Make a note of the hex value for the character(s). If you are using barcodes to create your output sequence, use the Programming Chart, beginning on page 215 to read the alphanumeric combination that represents the ASCII characters. (99 is the universal number, indicating all characters.)
5. End Output Sequence Editor Use FF to terminate this string or to begin another output sequence. If you are using barcodes, scan F F. Scan Save to save your entries.
Other Programming Selections
If you are creating an output sequence using barcodes, scan Discard (page 216) to exit without saving any output sequence changes.
Output Sequence Editor Commands
SEQBLK Sequence editor start command.
SEQPRE Add prefix to complete output sequences.
SEQSUF Add suffix to complete output sequences.
SEQSEP Add separators to complete output sequences.
SEQTTS1 Transmit partial sequence.
SEQSAT Define satisfactory subsets of full output sequence.
SEQTIM Timeout for sequence members when using SEQSAT.
SEQIPR Add prefix to partial output sequences.

Voyager 1350g User Guide

SEQISU Add suffix to partial output sequences.

SEQISE Add separators to partial output sequences.

TRGSTO Timeout for partial output sequences.

Termination string.

Examples outlining how to use these commands are shown below.

Output Sequence Example 1 – Three Symbologies

In this example, you are scanning PDF417, Code 128, and Code 39 barcodes, but you want the scanner to output Code 39 first, Code 128 second, and PDF417 third.

Set up the sequence editor with the following command line:

SEQBLK

sequence editor start command

code identifier for Code 39

9999

code length that must match for Code 39, 9999 = all lengths

start character match for Code 39, 43h = “C”

termination string for first code

code identifier for Code 128

9999

code length that must match for Code 128, 9999 = all lengths

start character match for Code 128, 54h = “T”

termination string for first code

code identifier for PDF417

9999

code length that must match for PDF417, 9999 = all lengths

start character match for PDF417, 4Dh = “M”

termination string for third code

The whole command line would look like this:

SEQBLK62999943FF6A999954FF7299994DFF

Voyager 1350g User Guide

The data is output as: CODE39SMPLTSTMSGCODE128MSGPDF417 See the next example to further refine this output.
Output Sequence Example 2 – Three Symbologies with <> Separators
In this example, you are scanning the same three barcodes, but you want <> brackets and a carriage return and line feed to separate your output.

The sequence editor would use the same command line as shown in Output Sequence Example 1 – Three Symbologies (page 48):

SEQBLK

sequence editor start command

code identifier for Code 39

9999

code length that must match for Code 39, 9999 = all lengths

start character match for Code 39, 43h = “C”

termination string for first code

code identifier for Code 128

9999

code length that must match for Code 128, 9999 = all lengths

start character match for Code 128, 54h = “T”

termination string for first code

code identifier for PDF417

9999

code length that must match for PDF417, 9999 = all lengths

start character match for PDF417, 4Dh = “M”

termination string for third code

But you would add your <> separators for each sequence:

SEQSEP99

separator for each sequence, 99 = all symbologies

left bracket (<)

Voyager 1350g User Guide

right bracket (>)

And add the carriage return and line feed as a suffix:

SEQSUF99

separator for suffixes, 99 = all symbologies

carriage return

line feed

The whole command line would look like this:

SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 A

The data is output as:

CODE39SMPL><MSGPDF417 [CR][LF]

Enter Output Sequence
If you are using barcodes to create your output sequence, scan Enter Output Sequence to begin scanning your string.

Enter Output Sequence
Partial Sequence
If an output sequence operation is terminated before all your output sequence criteria are met, the barcode data acquired to that point is a “partial sequence.” You can define how partial sequences are output using the same types of command strings you used to create output sequences.
Partial Sequence Example – Three Symbologies with <> Separators, but with a Damaged Code
In this example, you are scanning PDF417, Code 128, and Code 39 barcodes, and you want the scanner to output Code 39 first, Code 128 second, and PDF417 third, in brackets, as shown below, but the Code 39 barcode has been damaged and cannot be output.

Voyager 1350g User Guide

You would use the same command line as shown in Output Sequence Example 2 Three Symbologies with <> Separators (page 49):

SEQBLK

sequence editor start command

code identifier for Code 39

9999

code length that must match for Code 39, 9999 = all lengths

start character match for Code 39, 43h = “C”

termination string for first code

code identifier for Code 128

9999

code length that must match for Code 128, 9999 = all lengths

start character match for Code 128, 54h = “T”

termination string for first code

code identifier for PDF417

9999

code length that must match for PDF417, 9999 = all lengths

start character match for PDF417, 4Dh = “M”

termination string for third code

SEQSEP99

separator for each sequence, 99 = all symbologies

left bracket (<)

right bracket (>)

SEQSUF99

separator for suffixes, 99 = all symbologies

carriage return

line feed

And you would add >PARTIAL< as the prefix to note the partial sequence:

SEQTTS1

transmit partial sequence

SEQISU99

add partial sequence prefix, 99 = all symbologies

right bracket (>)

Voyager 1350g User Guide

left bracket (<)

The whole command line would look like this:

SEQBLK62999943FF6A999954FF7299994DFFSEQSEP993C3ESEQSUF990D0 ASEQTTS1SEQISU993E5041525449414C3C

The data is output as:

PARTIAL<TSTMSGCODE128<>MSGPDF417 [CR][LR}

Discard Partial Output Sequence
If you want to discard partial sequences when the output sequence operation is terminated before completion, scan Discard Partial Sequence.

Discard Partial Sequence
Output Sequence Timeouts
You can set a timeout for every code in the output sequence defined by the SEQBLK command. The scanner applies the shortest timeout corresponding to any of the codes that have been read during the current trigger session. When the timeout expires, the scanner sends all codes that it has been read in the order they appear in the sequence defined by SEQBLK.
To specify the timeout, use the SEQTIM command followed by a list of timeouts in milliseconds. Each timeout is specified as a 4-decimal digit terminated by FF. The timeout value 9999 is special and indicates that the timeout for that code is “infinite”.
The number of timeouts specified should correspond to the number of codes in the sequence defined by SEQBLK. You can specify one additional timeout, which will apply to codes not matching any member of the sequence. This can be useful if Require Output Sequence is On/Not Required. If you do not specify an additional timeout for codes not in the defined sequence, the last timeout specified by SEQTIM will apply.
Output Sequence Timeout Example
For example, if SEQBLK defines a 4-code sequence, you can specify timeouts of 5, 6, 7, and 8 seconds for codes 1-4 respectively using the command SEQTIM5000FF6000FF7000FF8000FF. Codes that are not part of the defined sequence would have an implied timeout of 8 seconds in this case (the final timeout in the list). To explicitly specify a timeout for such codes, you can include

Voyager 1350g User Guide

one more timeout at the end of the list. For example, to include a timeout of 1 second for non-sequence codes, use the command SEQTIM5000FF6000FF7000FF8000FF1000FF.
Satisfactory Subset of Full Sequence
You can define one or more subsets of barcodes from the complete sequence specified by SEQBLK. When you scan all the codes from one of these subsets, the scanner will transmit all the codes it has read in the sequence. The scanner sends the codes in the order defined by SEQBLK.
Note: To use the satisfactory subset feature, you must supply a timeout for each code in the sequence using SEQTIM.
Satisfactory Subset of Full Sequence Timeout Example
To specify a subset, list its members using the SEQSAT command and terminate each subset with FF. The members of each subset are specified as single hex digits corresponding to their index within the full sequence, 1 being the first. For example, to specify two subsets, the first consisting of the first and second code in the sequence and the second subset consisting of the second and third code, use the command SEQSAT12FF23FF.
To define a subset with an odd number of codes, insert a 0 before the final code index. For example, to define a 3-code subset consisting of the first, second, and third codes, use the command SEQSAT1203FF.
Default Output Sequence
Default Sequence programs the scanner to all universal values. Be certain you want to delete or clear all formats before you read the Default Sequence symbol.
Default Sequence
Require Output Sequence
When an output sequence is Required, all output data must conform to an edited sequence or the scanner will not transmit the output data to the host device. When it’s On/Not Required, the scanner will attempt to get the output data to conform to an edited sequence but, if it cannot, the scanner transmits all output data to the host device as is, or formatted according to the partial sequence output format (see Partial Sequence on page 50).
When the output sequence is Off, the barcode data is output to the host as the scanner decodes it. Default = Off.
Note: This selection is unavailable when the Multiple Symbols Selection is turned on.

Voyager 1350g User Guide

Required

On/Not Required

*Off
Good Read Tone – Output Sequences
The scanner may be programmed to either beep or click in response to a good read of each barcode in an output sequence, or to emit a beep or error tone for a partial sequence. Default = Good Read Click – Each Code in Sequence and Error Tone Partial Sequence Output.
,

Good Read Beep – Each Code in Sequence

Good Read Beep – Partial Sequence Output

Good Read Click – Each Code in Sequence
Error Tone – Partial Sequence Output
Multiple Symbols
When this programming selection is turned On, it allows you to read multiple symbols with a single pull of the scanner’s trigger. If you press and hold the trigger, aiming the scanner at a series of symbols, it reads unique symbols once, beeping and or vibrating (if turned on) for each read. The scanner attempts to find and

Voyager 1350g User Guide

decode new symbols as long as the trigger is pulled. The maximum number of barcodes read is 21. When this programming selection is turned Off, the scanner will only read the symbol closest to the aiming beam. Default = Off.
On

Off
No Read
With No Read turned On, the scanner notifies you if a code cannot be read. If using an EZConfig-Scanning Tool Scan Data Window (see page 160), an “NR” appears when a code cannot be read. If No Read is turned Off, the “NR” will not appear. Default = Off.
On
Off
If you want a different notation than “NR,” for example, “Error,” or “Bad Code,” you can edit the output message with NRDSTR menu command, such as: NRDSTRError or NRDSTRBad Code.
Video Reverse
Video Reverse is used to allow the scanner to read barcodes that are inverted. The Video Reverse Off barcode below is an example of this type of barcode. Scan Video Reverse Only to read only inverted barcodes. Scan Video Reverse and Standard Barcodes to read both types of codes. Note: After scanning Video Reverse Only, menu barcodes cannot be read. You must scan Video Reverse Off or Video Reverse and Standard Barcodes in order to read menu barcodes. Note: Images downloaded from the unit are not reversed. This is a setting for decoding only.

Voyager 1350g User Guide

Video Reverse Only * Video Reverse Off

Video Reverse and Standard Barcodes

Voyager 1350g User Guide

CHAPTER
4 DATA EDIT

Prefix/Suffix Overview
When a barcode is scanned, additional information is sent to the host computer along with the barcode data. This group of barcode data and additional, user- defined data is called a “message string.” The selections in this section are used to build the user-defined data into the message string.
Prefix and Suffix characters are data characters that can be sent before and after scanned data. You can specify if they should be sent with all symbologies, or only with specific symbologies. The following illustration shows the breakdown of a message string:

Prefix
1-11 alpha numeric & control characters

Scanned Data variable length

Suffix
1-11 alpha numeric & control characters

Points to Keep In Mind
· It is not necessary to build a message string. The selections in this chapter are only used if you wish to alter the default settings. Default prefix = None. Default suffix = None.
· A prefix or suffix may be added or cleared from one symbology or all symbologies.
· You can add any prefix or suffix from the ASCII Conversion Chart (Code Page 1252), beginning on page 206, plus Code I.D. and AIM I.D.
· You can string together several entries for several symbologies at one time.

Voyager 1350g User Guide

· Enter prefixes and suffixes in the order in which you want them to appear on the output.
· When setting up for specific symbologies (as opposed to all symbologies), the specific symbology ID value counts as an added prefix or suffix character.
· The maximum size of a prefix or suffix configuration is 200 characters, which includes header information.

Add a Prefix or Suffix:

Step 1. Scan the Add Prefix or Add Suffix symbol (page 59).

Step 2. Step 3.

Determine the 2 digit hex value from the Symbology Charts (beginning on page 203) for the symbology to which you want to apply the prefix or suffix. For example, for Code 128, Code ID is “j” and Hex ID is “6A”.
Scan the 2 hex digits from the Programming Chart, beginning on page 215, or scan 9, 9 for all symbologies.

To add the Code I.D., scan 5, C, 8, 0. To add the AIM I.D., scan 5, C, 8, 1. To add the serial number, scan 5, C, 8, 8. To add a backslash (), scan 5, C, 5, C.

Note: When adding a backslash (), you must scan 5C twice once to create the leading backslash and then to create the backslash itself.
Step 4. Repeat Steps 2 and 3 for every prefix or suffix character. Step 5. Scan Save to exit and save, or scan Discard to exit without saving.
Repeat the steps above to add a prefix or suffix for another symbology.

Example: Add a Tab Suffix to All Symbologies

Step 1. Step 2. Step 3.
Step 4.

Scan Add Suffix.
Scan 9, 9 from the Programming Chart, beginning on page 215 to apply this suffix to all symbologies.
Scan 0, 9 from the Programming Chart, beginning on page 215. This corresponds with the hex value for a horizontal tab, shown in the ASCII Conversion Chart (Code Page 1252), beginning on page 206.
Scan Save, or scan Discard to exit without saving.

Clear One or All Prefixes or Suffixes
You can clear a single prefix or suffix, or clear all prefixes/suffixes for a symbology. If you have been entering prefixes and suffixes for single symbologies, you can use Clear One Prefix (Suffix) to delete a specific character from a symbology. When you Clear All Prefixes (Suffixes), all the prefixes or suffixes for a symbology are deleted.

Voyager 1350g User Guide

Step 1. Scan the Clear One Prefix or Clear One Suffix symbol.

Step 2.

Determine the 2 digit hex value from the Symbology Chart (included in the Symbology Charts, beginning on page 203) for the symbology from which you want to clear the prefix or suffix.

Step 3. Scan the 2 digit hex value from the Programming Chart, beginning on page 215 or scan 9, 9 for all symbologies.

Your change is automatically saved.

Add a Carriage Return Suffix to All Symbologies
Scan the following barcode if you wish to add a carriage return suffix to all symbologies at once. This action first clears all current suffixes, then programs a carriage return suffix for all symbologies.

Prefix Selections

Add CR Suffix All Symbologies

Add Prefix
Clear All Prefixes
Suffix Selections

Clear One Prefix

Add Suffix

Clear One Suffix

Voyager 1350g User Guide

Clear All Suffixes
Function Code Transmit
By default, all ASCII control characters are transmitted with barcode data. These non-printable characters are translated into predefined key strokes, or CTRL+X functions (see ASCII Conversion Chart (Code Page 1252), beginning on page 206). If these key strokes interfere with your host’s software application, scan Disable to keep these ASCII control characters from being transmitted. Default = Enable.

Enable

Disable
Note: You can also use a custom data format (see Data Format beginning on page 63) to translate these characters into a more meaningful output.

Intercharacter, Interfunction, and Intermessage Delays
Some terminals drop information (characters) if data comes through too quickly. Intercharacter, interfunction, and intermessage delays slow the transmission of data, increasing data integrity.

Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each character of scanned data. Scan the Intercharacter Delay barcode below, then scan the number of 5ms delays from the Programming Chart, beginning on page 215, then Save.

Prefix

Scanned Data Suffix

1234 5 Intercharacter Delay

Intercharacter Delay

Voyager 1350g User Guide

To remove this delay, scan the Intercharacter Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 215.
Note: Intercharacter delays are not supported in USB serial emulation.
User Specified Intercharacter Delay
An intercharacter delay of up to 5000 milliseconds (in 5ms increments) may be placed after the transmission of a particular character of scanned data. Scan the Delay Length barcode below, then scan the number of 5ms delays from the Programming Chart, beginning on page 215, then Save.
Next, scan the Character to Trigger Delay barcode, then the 2-digit hex value for a printable character to trigger the delay (see Lower ASCII Reference Table, page
207.)

Delay Length

Character to Trigger Delay
To remove this delay, scan the Delay Length barcode, and set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 215.

Interfunction Delay
An interfunction delay of up to 5000 milliseconds (in 5ms increments) may be placed between the transmission of each control character in the message string. Scan the Interfunction Delay barcode below, then scan the number of 5ms delays, and the Save barcode from the Programming Chart, beginning on page 215.

Prefix

Scanned Data Suffix

STX 1 HT 2 3 4 5 CR LF

Interfunction Delays

Interfunction Delay

Voyager 1350g User Guide

To remove this delay, scan the Interfunction Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 215.
Intermessage Delay
An intermessage delay of up to 5000 milliseconds (in 5ms increments) may be placed between each scan transmission. Scan the Intermessage Delay barcode below, then scan the number of 5ms delays, and the Save barcode from the Programming Chart, beginning on page 215.
1st Scan Transmission 2nd Scan Transmission Intermessage Delay
Intermessage Delay
To remove this delay, scan the Intermessage Delay barcode, then set the number of delays to 0. Scan the Save barcode from the Programming Chart, beginning on page 215.

Voyager 1350g User Guide

CHAPTER
5 DATA FORMAT

Data Format Editor Introduction
You may use the Data Format Editor to change the scanner’s output. For example, you can use the Data Format Editor to insert characters at certain points in barcode data as it is scanned. The selections in the following pages are used only if you wish to alter the output. Default Data Format setting = None.
Normally, when you scan a barcode, it is output automatically. However, when you create a format, you must use a “send” command (see Send Commands on page 66) within the format program to output data.
Multiple formats may be programmed into the scanner. They are stacked in the order in which they are entered. However, the following list presents the order in which formats are applied:
1. Specific Terminal ID, Actual Code ID, Actual Length
2. Specific Terminal ID, Actual Code ID, Universal Length
3. Specific Terminal ID, Universal Code ID, Actual Length
4. Specific Terminal ID, Universal Code ID, Universal Length
5. Universal Terminal ID, Actual Code ID, Actual Length
6. Universal Terminal ID, Actual Code ID, Universal Length
7. Universal Terminal ID, Universal Code ID, Actual Length
8. Universal Terminal ID, Universal Code ID, Universal Length
The maximum size of a data format configuration is 2000 bytes, which includes header information.
If a barcode is read that fails the first data format, the next data format, if there is one, will be used on the barcode data. If there is no other data format, the raw data is output.

Voyager 1350g User Guide

If you have changed data format settings, and wish to clear all formats and return to the factory defaults, scan the Default Data Format code below.

Default Data Format
Show Data Format
Scan the barcode below to show current data format settings.

Data Format Settings

Add a Data Format

Step 1. Step 2.
Step 3.

Scan the Enter Data Format symbol (page 65).
Select Primary/Alternate Format Determine if this will be your primary data format, or one of 3 alternate formats. This allows you to save a total of 4 different data formats. To program your primary format, scan 0 from the Programming Chart, beginning on page 215. If you are programming an alternate format, scan 1, 2, or 3, depending on which alternate format you are programming. (See Primary/Alternate Data Formats on page 81 for further information.)
Terminal Type Refer to Terminal ID Table (page 66) and locate the Terminal ID number for your PC. Scan three numeric barcodes from the Programming Chart, beginning on page 215, to program the scanner for your terminal ID (you must enter 3 digits). For example, scan 0 0 3 for an AT wedge.

Note: 099 indicates all terminal types.

Step 4.

Code I.D. In the Symbology Charts, beginning on page 203, find the symbology to which you want to apply the data format. Locate the Hex value for that symbology and scan the 2 digit hex value from the Programming Chart, beginning on page 215.

If you wish to create a data format for all symbologies, with the exception of some specific symbologies, refer to B8 (page 79).

If you are creating a data format for Batch Mode Quantity, use 35 for the Code I.D.

Note: 99 indicates all symbologies.

Step 5.

Length Specify what length (up to 9999 characters) of data will be acceptable for
this symbology. Scan the four digit data length from the Programming

Voyager 1350g User Guide

Chart, beginning on page 215. For example, 50 characters is entered as 0050.

Note: 9999 indicates all lengths.

Step 6.

Editor Commands Refer to Data Format Editor Commands (page 66). Scan the symbols that represent the command you want to enter.

Step 7. Scan Save to save your data format, or Discard to exit without saving your changes.

Enter Data Format

Save

Discard
Other Programming Selections
· Clear One Data Format This deletes one data format for one symbology. If you are clearing the primary format, scan 0 from the Programming Chart, beginning on page 215. If you are clearing an alternate format, scan 1, 2, or 3, depending on the format you are clearing. Scan the Terminal Type and Code I.D. (see Symbology Charts on page 203), and the barcode data length for the specific data format that you want to delete. All other formats remain unaffected.
· Clear all Data Formats This clears all data formats.
· Save Exit and save your data format changes.
· Discard Exit without saving any data format changes.

Clear One Data Format

Clear All Data Formats

Voyager 1350g User Guide

Save

Discard

Terminal ID Table

Terminal USB
Serial

Model(s) PC keyboard (HID) Mac Keyboard PC Keyboard (Japanese) Serial (COM driver required) HID POS USB SurePOS Handheld USB SurePOS Tabletop RS232

Terminal ID 124 125 134 130 131 128 129 000

Data Format Editor Commands
When working with the Data Format Editor, a virtual cursor is moved along your input data string. The following commands are used to both move this cursor to different positions, and to select, replace, and insert data into the final output.

Send Commands
Send all characters
F1 Include in the output message all of the characters from the input message, starting from current cursor position, followed by an insert character. Syntax = F1xx where xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.

Voyager 1350g User Guide

Send a number of characters
F2 Include in the output message a number of characters followed by an insert character. Start from the current cursor position and continue for “nn” characters or through the last character in the input message, followed by character “xx.” Syntax = F2nnxx where nn stands for the numeric value (00-99) for the number of characters, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
F2 Example: Send a number of characters
Send the first 10 characters from the barcode above, followed by a carriage return. Command string: F2100D F2 is the “Send a number of characters” command 10 is the number of characters to send 0D is the hex value for a CR The data is output as: 1234567890
F2 and F1 Example: Split characters into 2 lines Send the first 10 characters from the barcode above, followed by a carriage return, followed by the rest of the characters. Command string: F2100DF10D F2 is the “Send a number of characters” command 10 is the number of characters to send for the first line 0D is the hex value for a CR F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234567890 ABCDEFGHIJ

Voyager 1350g User Guide

Send all characters up to a particular character
F3 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search character “ss,” followed by an insert character. The cursor is moved forward to the “ss” character. Syntax = F3ssxx where ss stands for the search character’s hex value for its ASCII code, and xx stands for the insert character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
F3 Example: Send all characters up to a particular character

Using the barcode above, send all characters up to but not including “D,” followed by a carriage return.
Command string: F3440D
F3 is the “Send all characters up to a particular character” command
44 is the hex value for a ‘D”
0D is the hex value for a CR
The data is output as: 1234567890ABC
Send all characters up to a string
B9 Include in the output message all characters from the input message, starting with the character at the current cursor position and continuing to, but not including, the search string “s…s.” The cursor is moved forward to the beginning of the “s…s” string. Syntax = B9nnnns…s where nnnn stands for the length of the string, and s…s stands for the string to be matched. The string is made up of hex values for the characters in the string. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
B9 Example: Send all characters up to a defined string

Using the barcode above, send all characters up to but not including “AB.” Command string: B900024142 B9 is the “Send all characters up to a string” command 0002 is the length of the string (2 characters) 41 is the hex value for A

Voyager 1350g User Guide

42 is the hex value for B The data is output as: 1234567890
Send all but the last characters
E9 Include in the output message all but the last “nn” characters, starting from the current cursor position. The cursor is moved forward to one position past the last input message character included. Syntax = E9nn where nn stands for the numeric value (00-99) for the number of characters that will not be sent at the end of the message.
Insert a character multiple times
F4 Send “xx” character “nn” times in the output message, leaving the cursor in the current position. Syntax = F4xxnn where xx stands for the insert character’s hex value for its ASCII code, and nn is the numeric value (00-99) for the number of times it should be sent. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes. E9 and F4 Example: Send all but the last characters, followed by 2 tabs
Send all characters except for the last 8 from the barcode above, followed by 2 tabs. Command string: E908F40902 E9 is the “Send all but the last characters” command 08 is the number of characters at the end to ignore F4 is the “Insert a character multiple times” command 09 is the hex value for a horizontal tab 02 is the number of times the tab character is sent The data is output as: 1234567890AB
Insert a string
BA Send “ss” string of “nn” length in the output message, leaving the cursor in the current position. Syntax = BAnnnns…s where nnnn stands for the length of the string, and s…s stands for the string. The string is made up of hex values for the characters in the string. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.

Voyager 1350g User Guide

B9 and BA Example: Look for the string “AB” and insert 2 asterisks (**)

Using the barcode above, send all characters up to but not including “AB.” Insert 2 asterisks at that point, and send the rest of the data with a carriage return after. Command string: B900024142BA00022A2AF10D B9 is the “Send all characters up to a string” command 0002 is the length of the string (2 characters) 41 is the hex value for A 42 is the hex value for B BA is the “Insert a string” command 0002 is the length of the string to be added (2 characters) 2A is the hex value for an asterisk () 2A is the hex value for an asterisk () F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 1234567890**ABCDEFGHIJ
Insert symbology name
B3 Insert the name of the barcode’s symbology in the output message, without moving the cursor. Only symbologies with a Honeywell ID are included (see Symbology Charts on page 203). Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
Insert barcode length
B4 Insert the barcode’s length in the output message, without moving the cursor. The length is expressed as a numeric string and does not include leading zeros. B3 and B4 Example: Insert the symbology name and length

Send the symbology name and length before the barcode data from the barcode above. Break up these insertions with spaces. End with a carriage return.
Command string: B3F42001B4F42001F10D

Voyager 1350g User Guide

B3 is the “Insert symbology name” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent B4 is the “Insert barcode length” command F4 is the “Insert a character multiple times” command 20 is the hex value for a space 01 is the number of times the space character is sent F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: Code128 20 1234567890ABCDEFGHIJ

Insert key strokes

B5 Insert a key stroke or combination of key strokes. Key strokes are dependent on your keyboard (see Keyboard Key References on page 212). Any key can be inserted, including arrows and functions. Syntax = 5CB5xxssnn where xx is the number of keys pressed (without key modifiers), ss is the key modifier from the table below, and nn is the key number from the Keyboard Key References, page 212.

Key Modifiers No Key Modifier Shift Left Shift Right Alt Left Alt Right Control Left Control Right

Hex 00 01 02 04 08 10 20

For example, B501021F inserts an “A” on a 104 key, U.S. style keyboard. B5 = the command, 01 = number of key press events (without the key modifier), 02 is the key modifier for Shift Right, and 1F is the “a” key. If a lower case “a” were to be inserted, B501001F would be entered.

Voyager 1350g User Guide

If there are three keystrokes, the syntax would change from B5xxssnn for one keystroke to B5xxssnnssnnssnn. An example that would insert “abc” is as follows: B503001F00320030F833.
Note: Key modifiers can be added together when needed. The sum is converted to hexadecimals.
Example: Control Left+Shift Left = 17, converted to hexadecimal = 11.
Move Commands
Move the cursor forward a number of characters
F5 Move the cursor ahead “nn” characters from current cursor position. Syntax = F5nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved ahead. F5 Example: Move the cursor forward and send the data
Move the cursor forward 3 characters, then send the rest of the barcode data from the barcode above. End with a carriage return. Command string: F503F10D F5 is the “Move the cursor forward a number of characters” command 03 is the number of characters to move the cursor F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 4567890ABCDEFGHIJ

Move the cursor backward a number of characters F6 Move the cursor back “nn” characters from current cursor position. Syntax = F6nn where nn is the numeric value (00-99) for the number of characters the cursor should be moved back. Move the cursor to the beginning F7 Move the cursor to the first character in the input message. Syntax = F7.

Voyager 1350g User Guide

FE and F7 Example: Manipulate barcodes that begin with a 1

Search for barcodes that begin with a 1. If a barcode matches, move the cursor back to the beginning of the data and send 6 characters followed by a carriage return. Using the barcode above: Command string: FE31F7F2060D FE is the “Compare characters” command 31 is the hex value for 1 F7 is the “Move the cursor to the beginning” command F2 is the “Send a number of characters” command 06 is the number of characters to send 0D is the hex value for a CR The data is output as: 123456
Move the cursor to the end
EA Move the cursor to the last character in the input message. Syntax = EA.
Search Commands
Search forward for a character
F8 Search the input message forward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F8xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes. F8 Example: Send barcode data that starts after a particular character

Search for the letter “D” in barcodes and send all the data that follows, including the “D.” Using the barcode above: Command string: F844F10D F8 is the “Search forward for a character” command 44 is the hex value for “D”

Voyager 1350g User Guide

F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: DEFGHIJ
Search backward for a character
F9 Search the input message backward for “xx” character from the current cursor position, leaving the cursor pointing to the “xx” character. Syntax = F9xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
Search forward for a string
B0 Search forward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B0000454657374 will search forward for the first occurrence of the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes. B0 Example: Send barcode data that starts after a string of characters
Search for the letters “FGH” in barcodes and send all the data that follows, including “FGH.” Using the barcode above: Command string: B00003464748F10D B0 is the “Search forward for a string” command 0003 is the string length (3 characters) 46 is the hex value for “F” 47 is the hex value for “G” 48 is the hex value for “H” F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: FGHIJ

Voyager 1350g User Guide

Search backward for a string
B1 Search backward for “s” string from the current cursor position, leaving cursor pointing to “s” string. Syntax = B1nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B1000454657374 will search backward for the first occurrence of the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
Search forward for a non-matching character
E6 Search the input message forward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E6xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
E6 Example: Remove zeros at the beginning of barcode data
This example shows a barcode that has been zero filled. You may want to ignore the zeros and send all the data that follows. E6 searches forward for the first character that is not zero, then sends all the data after, followed by a carriage return. Using the barcode above:
Command string: E630F10D
E6 is the “Search forward for a non-matching character” command
30 is the hex value for 0
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 37692
Search backward for a non-matching character
E7 Search the input message backward for the first non-“xx” character from the current cursor position, leaving the cursor pointing to the non-“xx” character. Syntax = E7xx where xx stands for the search character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.

Voyager 1350g User Guide

Miscellaneous Commands
Suppress characters
FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position, as the cursor is advanced by other commands. When the FC command is encountered, the suppress function is terminated. The cursor is not moved by the FB command. Syntax = FBnnxxyy . .zz where nn is a count of the number of suppressed characters in the list, and xxyy .. zz is the list of characters to be suppressed. FB Example: Remove spaces in barcode data
This example shows a barcode that has spaces in the data. You may want to remove the spaces before sending the data. Using the barcode above: Command string: FB0120F10D FB is the “Suppress characters” command 01 is the number of character types to be suppressed 20 is the hex value for a space F1 is the “Send all characters” command 0D is the hex value for a CR The data is output as: 34567890
Stop suppressing characters
FC Disables suppress filter and clear all suppressed characters. Syntax = FC.
Replace characters
E4 Replaces up to 15 characters in the output message, without moving the cursor. Replacement continues until the E5 command is encountered. Syntax = E4nnxx1xx2yy1yy2…zz1zz2 where nn is the total count of the number of characters in the list (characters to be replaced plus replacement characters); xx1 defines characters to be replaced and xx2 defines replacement characters, continuing through zz1 and zz2. E4 Example: Replace zeros with CRs in barcode data

Voyager 1350g User Guide

If the barcode has characters that the host application does not want included, you can use the E4 command to replace those characters with something else. In this example, you will replace the zeros in the barcode above with carriage returns.
Command string: E402300DF10D
E4 is the “Replace characters” command
02 is the total count of characters to be replaced, plus the replacement characters (0 is replaced by CR, so total characters = 2)
30 is the hex value for 0
0D is the hex value for a CR (the character that will replace the 0)
F1 is the “Send all characters” command
0D is the hex value for a CR
The data is output as: 1234 5678 ABC
Stop replacing characters
E5 Terminates character replacement. Syntax = E5.
Compare characters
FE Compare the character in the current cursor position to the character “xx.” If characters are equal, move the cursor forward one position. Syntax = FExx where xx stands for the comparison character’s hex value for its ASCII code. Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
Compare string
B2 Compare the string in the input message to the string “s.” If the strings are equal, move the cursor forward past the end of the string. Syntax = B2nnnnS where nnnn is the string length (up to 9999), and S consists of the ASCII hex value of each character in the match string. For example, B2000454657374 will compare the string at the current cursor position with the 4 character string “Test.” Refer to the ASCII Conversion Chart (Code Page 1252), beginning on page 206 for decimal, hex and character codes.
Check for a number
EC Check to make sure there is an ASCII number at the current cursor position. The format is aborted if the character is not numeric.

Voyager 1350g User Guide

EC Example: Only output the data if the barcode begins with a number If you want only data from barcodes that begin with a number, you can use EC to check for the number. Command string: ECF10D EC is the “Check for a number” command F1 is the “Send all characters” command 0D is the hex value for a CR

If this barcode is read,

the next data format, if there is one, will

be used on the data. If there is no other format, the format fails and the raw data is output as AB1234.

If this barcode is read:

the data is output as:

1234AB

Check for non-numeric character
ED Check to make sure there is a non-numeric ASCII character at the current cursor position. The format is aborted if the character is numeric. ED Example: Only output the data if the barcode begins with a letter If you want only data from barcodes that begin with a letter, you can use ED to check for the letter. Command string: EDF10D ED is the “Check for a non-numeric character” command F1 is the “Send all characters” command 0D is the hex value for a CR

If this barcode is read,

the next data format, if there is one, will be

used on this data. If there is no other format, the format fails and the raw data is output as 1234AB.

If this barcode is read:
AB1234

the data is output as:

Voyager 1350g User Guide

Insert a delay
EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the current cursor position. Syntax = EFnnnn where nnnn stands for the delay in 5ms increments, up to 9999. This command can only be used with keyboard emulation.
Discard Data
B8 Discards types of data. For example, you may want to discard Code 128 barcodes that begin with the letter A. In step 4 (page 64), select 6A (for Code 128), and in step 5, select 9999 (for all lengths). Enter FE41B8 to compare and discard Code 128 barcodes that begin with the letter A. Syntax = B8.
Note: The B8 command must be entered after all other commands. The Data Format must be Required (see page 79) in order for the B8 command to work. If Data Format is On, but Not Required (page 80), barcode data that meets the B8 format is scanned and output as usual. Because the data format needs to be On and Required (page 80) for the B8 command, you must input data formats for all barcodes you wish to discard as well as all barcodes you wish to output. Other data format settings impact the B8 command. If Data Format Non-Match Error Tone is On (page 80), the scanner emits an error tone. If Data format Non- Match Error Tone is Off, the code is disabled for reading and no tone is sounded.
Data Formatter
When Data Formatter is turned Off, the barcode data is output to the host as read, including prefixes and suffixes.
Data Formatter Off
You may wish to require the data to conform to a data format you have created and saved. The following settings can be applied to your data format:
· Data Formatter On, Not Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted.
· Data Formatter On, Not Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. If a data format is not found for that symbol, the prefixes and suffixes are transmitted.
· Data Format Required, Keep Prefix/Suffix Scanned data is modified according to your data format, and prefixes and suffixes are transmitted. Any data that does not match your data format

Voyager 1350g User Guide

requirements generates an error tone and the data in that barcode is not transmitted. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. · Data Format Required, Drop Prefix/Suffix Scanned data is modified according to your data format. If a data format is found for a particular symbol, those prefixes and suffixes are not transmitted. Any data that does not match your data format requirements generates an error tone. If you wish to process this type of barcode without generating an error tone, see Data Format Non-Match Error Tone. Choose one of the following options. Default = Data Formatter On, Not Required, Keep Prefix/Suffix.

Data Formatter On, Not Required,
Keep Prefix/Suffix
Data Formatter On, Not Required,
Drop Prefix/Suffix
Data Format Required, Keep Prefix/Suffix
Data Format Required, Drop Prefix/Suffix
Data Format Non-Match Error Tone
When a barcode is encountered that doesn’t match your required data format, the scanner normally generates an error tone. However, you may want to continue scanning barcodes without hearing the error tone. If you scan the Data Format Non-Match Error Tone Off barcode, data that doesn’t conform to your data format is not transmitted, and no error tone will sound. If you wish to hear the error tone when a non-matching barcode is found, scan the Data Format Non-Match Error Tone On barcode. Default = Data Format Non-Match Error Tone On.
Data Format Non-Match Error Tone On

Voyager 1350g User Guide

Data Format Non-Match Error Tone Off
Primary/Alternate Data Formats
You can save up to four data formats, and switch between these formats. Your primary data format is saved under 0. Your other three formats are saved under 1, 2, and 3. To set your device to use one of these formats, scan one of the barcodes below.

Primary Data Format

Data Format 1

Data Format 2
Data Format 3
Single Scan Data Format Change
You can also switch between data formats for a single scan. The next barcode is scanned using an alternate data format, then reverts to the format you have selected above (either Primary, 1, 2, or 3). For example, you may have set your device to the data format you saved as Data Format 3. You can switch to Data Format 1 for a single trigger pull by scanning the Single Scan-Data Format 1 barcode below. The next barcode that is scanned uses Data Format 1, then reverts back to Data Format 3.

Single Scan-Primary Data Format

Voyager 1350g User Guide

Single Scan-Data Format 2

Single Scan-Data Format 1 Single Scan-Data Format 3

Voyager 1350g User Guide

CHAPTER
6 SYMBOLOGIES

This programming section contains the following menu selections. Refer to Chapter 9 for settings and defaults.

· All Symbologies · Aztec Code · China Post (Hong Kong 2 of 5) · Chinese Sensible (Han Xin) Code · Codabar · Codablock A · Codablock F · Code 11 · Code 128 · Code 32 Pharmaceutical (PARAF) · Code 39 · Code 93
· Data Matrix
· Digimarc BarcodeTM · DotCode · EAN/JAN-13 · EAN/JAN-8 · GS1 Composite Codes · GS1 DataBar Expanded
· GS1 DataBar Limited
· GS1 DataBar Omnidirectional · GS1 Emulation · GS1-128

· Interleaved 2 of 5 · Korea Post · Label Code · Matrix 2 of 5 · MaxiCode · MicroPDF417 · MSI · NEC 2 of 5 · Postal Codes – 2D · Postal Codes – Linear · PDF417 · QR Code · Straight 2 of 5 IATA (two-bar start/
stop)
· Straight 2 of 5 Industrial (three-bar start/stop)
· TCIF Linked Code 39 (TLC39) · Telepen · Trioptic Code · UPC-A · UPC-A/EAN-13 with Extended
Coupon Code · UPC-E0 · UPC-E1

Voyager 1350g User Guide

All Symbologies
For best scanner performance, you should only enable the symbologies that you need. Scan All Symbologies Off to disable all symbologies, then enable the symbologies you need by scanning the On barcode for each symbology.

All Symbologies Off

Message Length Description
You are able to set the valid reading length of some of the barcode symbologies. You may wish to set the same value for minimum and maximum length to force the scanner to read fixed length barcode data. This helps reduce the chances of a misread.
Example: Decode only those barcodes with a count of 9-20 characters. Min. length = 09 Max. length = 20
Example: Decode only those barcodes with a count of 15 characters. Min. length = 15 Max. length = 15
For a value other than the minimum and maximum message length defaults, scan the barcodes included in the explanation of the symbology, then scan the digit value of the message length and Save barcodes from the Programming Chart, beginning on page 215. The minimum and maximum lengths and the defaults are included with the respective symbologies.

Codabar

Codabar On/Off

Voyager 1350g User Guide

Off
Codabar Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit.

Transmit

Don’t Transmit
Codabar Check Character
Codabar check characters are created using different “modulos.” You can program the scanner to read only Codabar barcodes with Modulo 16 check characters. Default = No Check Character. No Check Character indicates that the scanner reads and transmits barcode data with or without a check character. When Check Character is set to Validate and Transmit, the scanner will only read Codabar barcodes printed with a check character, and will transmit this character at the end of the scanned data. When Check Character is set to Validate, but Don’t Transmit, the unit will only read Codabar barcodes printed with a check character, but will not transmit the check character with the scanned data.
No Check Character
Validate Modulo 16 and Transmit

Validate Modulo 16, but Don’t Transmit

Voyager 1350g User Guide

Codabar Concatenation
Codabar supports symbol concatenation. When you enable concatenation, the scanner looks for a Codabar symbol having a “D” start character, adjacent to a symbol having a “D” stop character. In this case the two messages are concatenated into one with the “D” characters omitted.

A1 2 3 4D D5 6 7 8A
Select Require to prevent the scanner from decoding a single “D” Codabar symbol without its companion. This selection has no effect on Codabar symbols without Stop/Start D characters.

Off
Require
Codabar Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 84) for additional information. Minimum and Maximum lengths = 2-60. Minimum Default = 4, Maximum Default = 60.

Minimum Message Length

Maximum Message Length

Voyager 1350g User Guide

Code 39

< Default All Code 39 Settings >

Code 39 On/Off

On
Off
If you are reading Code 39 barcodes, Codablock A should remain disabled. If you are enabling Codablock A (see Codablock A on page 122), you should disable Code 39.
Code 39 Start/Stop Characters
Start/Stop characters identify the leading and trailing ends of the barcode. You may either transmit, or not transmit Start/Stop characters. Default = Don’t Transmit.
Transmit
Don’t Transmit
Code 39 Check Character
No Check Character indicates that the scanner reads and transmits barcode data with or without a check character. When Check Character is set to Validate, but Don’t Transmit, the unit only reads Code 39 barcodes printed with a check character, but will not transmit the check character with the scanned data.

Voyager 1350g User Guide

When Check Character is set to Validate and Transmit, the scanner only reads Code 39 barcodes printed with a check character, and will transmit this character at the end of the scanned data. Default = No Check Character.

No Check Character
Validate, but Don’t Transmit
Validate and Transmit
Code 39 Message Length
Scan the barcodes below to change the message length. Refer to Message Length Description (page 84) for additional information. Minimum and Maximum lengths = 0-48. Minimum Default = 0, Maximum Default = 48.
Minimum Message Length
Maximum Message Length
Code 39 Append
This function allows the scanner to append the data from several Code 39 barcodes together before transmitting them to the host computer. When the scanner encounters a Code 39 barcode with the append trigger character(s), it buffers Code 39 barcodes until it reads a Code 39 barcode that does not have the append trigger. The data is then transmitted in the order in which the barcodes were read (FIFO). Default = Off.
On
Off

Voyager 1350g User Guide

Code 32 Pharmaceutical (PAR

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format) >>

Download This Manual (PDF format)

Download this manual >>

Honeywell Voyager 1350g Corded Area Imaging Scanner User Guide

Voyager 1350g Corded Area Imaging Scanner

Product Information: VoyagerTM 1350g Corded Area-Imaging

Specifications:

Chapter 1 – Get Started

About This Manual

Unpack Your Device

Connect the Device

Chapter 2 – Program the Interface

USB Serial

CTS/RTS Emulation

ACK/NAK Mode

Chapter 3 – Input/Output Settings

Chapter 4 – Data Edit

Chapter 5 – Data Format

Data Format Editor Introduction

Show Data Format

Add a Data Format

Chapter 6 – Symbologies

Planet Code Check Digit

Postnet Check Digit

Australian Post Interpretation

FAQ

Q: Where can I find patent information for the VoyagerTM 1350g

References

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Honeywell User Manuals

Related Manuals