amazon basics B00TOAK5Q6 6 Sheet High Security Micro Cut Paper and Credit Card Shredder Instruction Manual

amazon basics B00TOAK5Q6 6 Sheet High Security Micro Cut Paper and Credit

Card Shredder

Important Safety Instructions

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using electrical products, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons including the following:

DANGER
Risk of electric shock!
Do not attempt to repair the product. In case of malfunction, repairs are to be conducted by qualified personnel only.
CAUTION Risk of injury!
The product has very sharp exposed cutters on the underside. Never touch the underside of the shredding mechanism.

• Always switch the product off and unplug the power supply cord from the socket-outlet when not in use, before cleaning, moving, or emptying the paper bin.
• Never dispose of flammable chemicals or materials that have come into contact with flammable chemicals (for example, nail polish, acetone and gasoline) in the paper bin.
• The ventilation should not be impeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.
• The minimum distances of 5 cm around the product is required for sufficient ventilation.
• Never shred large paper clips, metal credit cards, window or insulated envelopes, continuous forms, newsprint, bound pages (for example: notepads, checkbooks, magazines, etc.), transparencies, laminated documents, cardboard, any items with adhesives, hard materials or plastic (except plastic credit cards).
• The socket-outlet shall be installed near the product and shall be easily accessible.
• Empty the bin regularly. An overfilled bin might lead to jams.
• The product shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the product.
• Regularly check the power plug and power supply cord for damage. If the power supply cord is damaged, it must be replaced by a qualified person in order to avoid a hazard.
• Never try to clean or clear the shredder cutters.
• Never shred beyond the specified sheet capacity. This may result in product damage.
• This product should be used in moderate climates only.

Symbols Explanation

Intended Use

• This product is intended for shredding paper, plastic credit cards and similar materials only.
• This product is intended for office and private use.
• This product is intended to be used in dry indoor areas only.

Before First Use

DANGER
Risk of suffocation!
Keep any packaging materials away from children and pets – these materials are a potential source of danger, e.g. suffocation.

• Remove all the packing materials.
• Remove and review all components before assembly.
• Check the product for transport damages.
• Before connecting the product to the power supply, check that the power supply voltage and current rating corresponds with the power supply details shown on the product rating label.

Product Description

• A. Slide control
• B. Indicator
• C. Feed slot
• D. Power supply cord with plug
• E. Handle
• F. Main unit
• G. Bin
• H. Bin window

Assembly and Placement

NOTICE Keep a minimum of 5 cm between the product and any walls for sufficient ventilation.
Place the main unit (F) on the bin (G). Make sure that the curve on the back fits into the slot (Fig. 1).

Operation

Do not shred

NOTICE

• Always set the slide control (A) to the O position and unplug the product when not in use.
• Do not place the plastic bags from the bin (G). This may cause the product to not operate properly.

Switching on/off

1. Connect the power plug (D) to a suitable socket-outlet.
2. Switch on the product by setting the slide control (A) to I position.
3. Switch off the product by setting the slide control (A) to O position.

Slide control

Set the slide control (A) to the mode desired.

• ON: While in ON mode, the motor does not start running until paper or a card is inserted into the feed slot (C). Always feed the paper in as straight as possible. When the paper or card has passed through, the motor stops automatically. The indicator (B) stays green.
• OFF: While in Off mode, the product is connected to power, but is not switched on for shredding. The indicator (B) goes off.
• REVERSE: When there is a paper jam, the reverse mode can be used to help clear the cutters of material that did not pass through. While in REVERSE mode, the product continues to reverse even without any paper or items placed in it. The indicator (B) stays green.

Shredding

NOTICE

• A sensor is located in the centre of the feed slot (C). Always insert the item into the centre of the feed slot (C).
• This product can shred staples and small paper clips. However, it is recommended to remove paper clips whenever possible to extend the lifespan of the product.
• Look through the bin window (H) to see if the bin (G) is full.

1. Paper
   • Do not exceed the sheet count per pass (5 – 6 sheets max.)
   • One folded sheet of paper equates to 2 sheets of paper. Heavier paper, humidity or supply voltage lower than the rated voltage may reduce shredding capacity.

2. Credit card
   • Only shred credit cards by feeding them vertically into the centre of the feed slot (C).
   • Release the card when shredding begins.
   • The sensor is located in the centre of the feed slot (C). Do not insert credit cards at the sides of the feed slot (C).
   • Only feed in one credit card at a time.

Status indicators

• READY: This indicator (B) flashes green when the slide control (A) is set to |.
• OVERHEAT: This indicator (B) flashes red when the product has overheated. The product automatically shuts off. Set the slide control (A) to O for 30 minutes or longer before resuming normal operation.

Emptying the Bin

WARNING Risk of injury!

• It is recommended to switch to O mode when lifting the product. The cutters on the feed slot (C) may cause hair or clothes to accidentally go through and cause injury.
• The cutters on the bottom of the product are exposed. Please exercise caution when removing papers that are stuck when emptying the bin (G).

NOTICE Monitor the contents of the bin (G) through the transparent window (H) (Fig. 6).

1. When the bin is full, set the slide control (A) to O mode.
2. Carefully lift the main unit (F) from the bin (G).
3. Empty the bin (G) and carefully remove the remnants from the bottom.

Cleaning and Maintenance

• WARNING
  Risk of electric shock!

  • To prevent electric shock, unplug the product before cleaning.
  • During cleaning do not immerse the electrical parts of the product in water or other liquids. Never hold the product under running water.

• WARNING
  Risk of explosion!
  Do not spray or keep any aerosol/pressurized products in or around the product.

Cleaning

• Always check if the bin (G) is full through the bin window (H).
• To clean the product, wipe with a soft, slightly damp cloth.
• Wipe the product dry after cleaning.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.
• Do not try to clean or clear the shredder cutters on the feed slot (C).
• Never use anything flammable to clean the shredder. This may result in serious injury or damage to the product.

Cleaning the sensor

1. Unplug the product from the power supply.
2. Using a cotton swab, gently wipe away dust and buildup from the sensor (Fig. 7).

Oiling procedure

NOTICE If not oiled regularly, the product may exhibit diminished shredding capacity, intrusive noise when shredding and could ultimately stop operating. To avoid these problems, oil the shredder once a month.

Using shredder oil (not provided)

1. Set the slide control (A) to O.
2. Drizzle some oil into the feed slot (C) (Fig. 8).
3. Set the slide control (A) to KiS to activate reverse mode for 3 – 5 seconds.

Using lubricating sheets (not provided)
Lubricant sheet B01H7M7BXM, B01H7M7FZ6

1. Insert a sheet into the feed slot (C) and set the slide control (A) to | (Fig. 9).
2. After shredding, set the slide control (A) to /k for 10 seconds to make sure the cutters are coated.

Storage
Store the product in its original packaging in a dry area. Keep away from children and pets.

Plug fuse replacement (for UK only)

• Use a flat screwdriver to open the fuse compartment cover.
• Remove the fuse and replace with the same type (5 A, BS1362). Refit the cover.

Maintenance
WARNING
Failure to properly maintain your shredder will void the warranty.

• Any other servicing than mentioned in this manual should be performed by a professional repair centre.
• Oil the shredder blades every month with basic cooking oil or shredder oil. Follow oiling procedure on chapter 9.2. It helps to keep the shredder blades operating well over many years of use.

Frequently Asked Questions

Disposal (for Europe only)

The Waste Electrical and Electronic Equipment (WEEE) laws aim to minimise the impact of electrical and electronic goods on the environment and human health, by increasing re-use and recycling and by reducing the amount of WEEE going to landfill. The symbol on this product or its packaging signifies that this product must be disposed separately from ordinary household wastes at its end of life. Be aware that this is your responsibility to dispose of electronic equipment at recycling centres in order to conserve natural resources. Each country should have its collection centres for electrical and electronic equipment recycling. For information about your recycling drop off area, please contact your related electrical and electronic equipment waste management authority, your local city office, or your household waste disposal service.

Specifications

• Model number AU610MA, AU620MA
• Rated voltage 220 – 240 V~, 50/60 Hz
• Rated current 1.2 A
• Protection class Class II
• Sheet capacity
  • 5 sheets of 80 gsm paper*
  • 6 sheets of 70 gsm paper*
• Shred type Micro-cut
• Paper shred size 4 mm x 12 mm pieces
• Paper feed entry width 220 mm
• Credit card capacity 1 at a time
• Duty cycle 3 minutes on / 30 minutes off
• Paper bin volume 15.5 L

One folded sheet of paper equates to 2 sheets of paper
Heavier paper, humidity or other than rated voltage may reduce shredding capacity

Importer Information

• For EU
  • Postal: Amazon EU S.à r.L., 38 avenue John F. Kennedy, L-1855 Luxembourg
  • Business Reg.: 134248
• For UK
  • Postal: Amazon EU SARL, UK Branch, 1 Principal Place, Worship St, London EC2A 2FA, United Kingdom
  • Business Reg.: BR017427

Feedback and Help

• We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review. amazon.co.uk/review/review-your-purchasesi‡
• If you need help with your Amazon Basics product, please use the website or number below. amazon.co.uk/gp/help/customer/contact-us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>