PEACHAR X200 Dog Training Collar User Manual

PEACHAR X200 Dog Training Collar

Dog Training Collar Model: X200

User Manual
Please read the user manual carefully before using the product

PACKAGE INCLUDES

OVERVIEW

Handheld Remote

Digital display

Receiver

Important Safety Information

This is the safety alert symbol. It is used to alert you to potential injury hazards. Obey all safety messages that follow this symbol to avoid possible injury.

WARNING
WARNING indicates a hazardous situation if not avoided could result in serious injury. Not for use with aggressive dogs. Do not use this product if your dog is prone to aggressive behavior. Aggressive dogs can cause severe injury to their owners and others. If you are not sure that this product is right for your dog, please talk to your veterinarian or a certified trainer.

CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous situation if not avoided could result in minor or moderate injury.

• Safety during on-leash training . It is vitally important that you and your dog remain safe while learning during on-leash training. Your dog should be on a strong leash, long enough for him to attempt to chase an object, but short enough for him not to reach a road or other unsafe area. You must also be physically strong enough to restrain your dog when he tries to chase.
• This pet training device is not a toy, keep away from children.

CAUTION
CAUTION, used with the safety alert symbol, indicates a hazardous situation which if not avoided, could result in harm to your pet. Risk of skin damage . Please read and follow the instructions in this manual . Proper fit of the collar is important. A collar worn for too long or made too tight on the pets neck may cause skin damage. Ranging from redness to pressure ulcers; this condition is commonly known as bed sores.

• Avoid leaving the collar on the dog for more than 12 hours per day.
• Possible reposition the collar on the pets neck every 1 to 3 hours .
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a leash to the electronic collar, it will cause excessive pressure on the contact points.
• When using a separate collar for a leash, don’t put pressure on the electronic collar.
• Wash the dog’s neck area and the contacts of the collar weekly with a damp cloth.
• Check the contact area daily for signs of a rash or a sore.
• If a rash or sore is found, discontinue use of the collar until the skin has healed, If the condition persists beyond 48 hours, see your veterinarian.

Note: The contact points must make direct contact with the skin underneath the dog’s neck. Verify the collar’s tightness by comfortably inserting one finger between the collar and the neck.

To maximize the battery life, remember to turn off the collar when it is not in use. Press and hold the power button for 3 secs to turn the Receiver off.

Security Keypa d: unlock or lock

Delivers a beep tone with non-adjustable volume to the collar.

Delivers vibration of the collar. To adjust the vibration intensity, press the Vibration button, followed by pressing the “Mode” button, and then use the Add Key + or Substract Key –

• Shock button: Delivers the currently selected level of shock stimulation to the collar.
• Shock+ button: Increases the stimulation level by 10% compared to the currently selected level
• Some consumers prefer instant access to a higher setting if the dog does not respond to lower levels.
• Shock intensity adjustment: Press the shock button, Follow by Pressing the “Mode” button, then use the Add Key + or Subtract Key – to adjust the intensity.

How to use the collar correctly

Transmitter Digital Screen

Receiver Indicator Light

How to find the best-suited level for each training mode?

The training remote has 18 stimulation levels of static shock & 8 levels of vibration. Always start at the lowest levels and work your way up. You can also feel the stimulation on your wrist to have a better understanding of which level is best suited for your dog in each training mode. This step is called; “The Recognition Level” A slight change in your dog’s behavior- Such as a sharp move ‘looking around’ or scratching the collar or flicking ears indicates the recognition level which is best suited for your dog.

Follow these steps to find your dog’s Recognition Level

1. Start at the lowest level (1,2,3) Press the shock/vibration button continuously for 1-2 sec.
   Note : The training buttons deliver stimulation for exactly 10 sec’. If needed further stimulation, Re-press the desired button.

2. If there is no reaction on a specific level; Repeat the stimulation level several times before moving up to the next level.

3. In no case, your dog should panic or yelp when receiving stimulation! If such a thing happens- You are way above the recognition level and you must go to a lower setting.

4. Going up the levels must be done gradually, Your dog’s reaction must be just as someone else will tickle you in the neck. Correcting your dog’s behavior must be gentle but strong enough to turn his attention to you. Even while off-leash

5. If you see no reaction from your dog while using the e-collar on a higher level; You will want to double-check the placement and fitting on the dog’s neck, If your dog has long fur – Use the longer contact points. Then go over the Recognition level process again.

Note: If your dog is not responding to any of the training modes- Please contact our customer service by email: support@peachar.cn

• Step 1 : Starting at Level 1 on the Digital Display, press the shock button to see dogs reaction.
• Step 2 : Move up through the Stimulation levels until your pet reliably responds to the Stimulation.
• Step 3 : If your dog continues to show no response at Level 10, check the fit of the Receiver Collar.
• If your dog has long or thick hair, change to a longer set of Contact Points, or dog’s hair will need to be trimmed around the Contact Point. if all of these steps have been done and dog continues to show nonreaction, see the ” How to Use Test Light Tool ” section.

Dog type suitable for dog trainer

Main Features

• Vibration, Tone and shock training model
• 8 adjustable vibration level and 18 adjustable shock level
• Dual batteries status display for Remote and Receiver
• Receiver collar IP68 waterproof (Remote non-waterproof)
• Remote range 1640-2300 feet
• Long life Lithium Polymer battery
• Big digital display
• Support maximum 3 receiver collars with one remote

How to Use Test Light Tool
A: Static function test

1. Make sure the Remote and Receiver Collar on.
2. Hold the Test Light tool contacts to the Contact Points
3. Press a Static button on the Remote Transmitter. The Test Light will be lighted.

B: As a tool to tighten or loosen the contact points.
For dogs with shorter fur, use 2 shorter contact points or attach conductive silicone to the contact points to make them softer. This may be more comfortable for your dog’s skin. For dogs with thicker fur, use 2 longer contact points or attach conductive silicone.

General Training Tips
To eliminate unwanted behavior, such as barking, please follow these training steps:

1. Put a separate non-metallic collar on your dog’s neck above the Receiver Collar and attach an 8-10 foot leash. Ensure that the extra collar does not put pressure on the Contact Points.
2. Hold the leash and the Remote Transmitter.
3. Choose your pet’s Recognition Level.
4. As soon as your pet starts barking, press the Stimulation button and give the command “No” or “No barking.”
5. Release the Stimulation button immediately once your dog stops barking, and verbally praise him.
6. If your pet ignores the stimulation, increase the Intensity level by 2 to 3.
7. Practice this exercise in several different areas.

How to Pair the Remote Transmitter & Receiver Collar
(Notes: You may skip this step because the set is already paired by factory setting .)

1. Make sure the Receiver is turned off
2. To turn on the collar receiver, just press the power button, the receiver will vibrate, and the green light will blink
3. Press the “CH” button on the remote to select channel you wish to pair. Then press and hold “CH” button until the “” blinks.
4. Press and hold the receiver collar’s on/off switch for Approx. 6 seconds. You’ll hear 3-4 “DI” sounds and see the green light start blinking. After this, the power level will display on the remote, confirming a successful pairing.

Support up to 3 Receiver Collars
(Note: Please skip this if you are using only one receiver. This setting is specifically for multiple receiver collars with one remote) Part I: Pairing with the 2nd or 3rd Receiver (Note: You should buy an additional receiver collar.)

• Receiver

1. Make sure the Receiver is turned off.
2. Press the power button, the receiver will vibrate, and the green light will blink.  

Remote:

3. Press the CH button to select the dog icon
4. Press the remote Pairing/Channel select button for 3-5 seconds until the signal light is flashing
5. Press and hold the on/off switch of the receiver collar for approximately 6s. You will hear 3-4 sounds of “DI” being emitted, and the green light will start blinking.

Then you will be able to see the power display of the receiver on the remote control screen, indicating that the pairing is successful.

Part II : Receiver Switching:

• Able to train 3 dogs simultaneously.
• Press the CH button to select the dog for training.

After-Sales Customer Service

Warranty
If you have any issues about product and need any help, please kindly contact our after sale service email. our customer service team will always be here to help and support you. Customer Service: support@peachar.cn Website: www.peachar.cn

http://www.peachar.cn

Compliance

FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions :

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Modification or changes to this equipment not expressly approved by Radio Systems Corporation may void the users authority to operate the equipment

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and , if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation. If interference does occur to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult customer care, the dealer, or an experienced radio / TV technician for help.

TANMMET INT’L BUSINESS LTD
Z9 Pantygraigwen Road, Pontypridd, Mid Glamorgan CF37 2RR, UK tanmetbiza@outlook.com

MADE IN CHINA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>