birch lighting MD 21225 Complete LED Strip Light Kits Instruction Manual

June 15, 2024
birch lighting

birch-lighting-LOGO

birch lighting MD 21225 Complete LED Strip Light Kits

birch-lighting-MD-21225-Complete-LED-Strip-Light-Kits-
PRODUCT

Specifications

  • Product: LED Strip Light Kits
  • Intended Use: Dry location use only
  • Warranty: One-year limited warranty

Installation
To install the LED Strip Light Kits, please follow the steps below:

  1. Clean the surface where you plan to install the strip lights.
  2. Measure and mark the desired length of the strip light.
  3. Cut the strip light at the designated cut points, ensuring you do not cut through any solder joints. Cutting interval: 4 inches.
  4. Peel off the adhesive backing from the strip light.
  5. Align and firmly press the strip light onto the cleaned surface.
  6. Connect the power supply to the strip light according to the provided instructions.
  7. Test the installation by turning on the power supply.
  8. If satisfied with the installation, secure any loose sections of the strip light using adhesive or mounting clips.

Tips
Here are some tips for installing and using the LED Strip Light Kits:

  • If you are unsure about the installation or want to test the product before permanent installation, consider using a painter’s tape for temporary installation.

Warranty
This product comes with a one-year limited warranty. The warranty is void if the product is improperly installed, improperly powered, abused, or used for purposes other than its intended use. Proof of purchase is required for all returns.

FAQ

  • Q: Can I install the LED Strip Light Kits in a wet location?
  • A: No, this product is designed for dry location use only. Installing it in a wet location can be dangerous and will void the warranty.
  • Q: What happens if I cut through a solder joint while cutting the strip light?
  • A: Cutting through a solder joint can damage the strip light and may cause it to malfunction. It is important to carefully cut at the designated intervals to avoid damaging the solder joints.
  • Q: How do I connect the power supply to the strip light?
  • A: The instructions for connecting the power supply to the strip light are provided with the product. Please follow the provided instructions to ensure a proper connection.

Safety Information

  • Do not stare directly at LEDs
  • Do not power while the LED tape is still on the reel
  • Keep low-voltage wiring separate from high-voltage wiring runs
  • For indoor/dry location use only

Installation

  • Unwind the tape from the reel and test before installation.birch-lighting-MD-21225-Complete-LED-Strip-Light-Kits-FIG- \(1\)
  • Tape may be cut to size at the copper pads or solder joints. Cut interval: 4 in.birch-lighting-MD-21225-Complete-LED-Strip-Light-Kits-FIG- \(2\)
  • Remove the protective backing from the adhesive and press the tape into place.birch-lighting-MD-21225-Complete-LED-Strip-Light-Kits-FIG- \(3\)

Tips

  • Make sure the surface is clean and dry before installing
  • Do not bend the LED tape
  • Use painter tape to temporarily install to test

Operation

birch-lighting-MD-21225-Complete-LED-Strip-Light-Kits-FIG-
\(4\)

Control of the kit will be either via an inline on/off switch or an included remote.

Troubleshooting

LED strip will not light

  • Make sure the outlet has power and that a switched outlet switch is on

Remote unresponsive

  • Move closer to the receiver
  • Check the battery and replace if needed

For support, visit birchlighting.com

One-year limited warranty

This product is for dry location use only. Improper installation, improper powering, abuse, or failure to use this device for its intended purpose will void the warranty. Proof of purchase is required for all returns.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. this device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

© 2023 Birch Lighting, Baltimore, MD 21225

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals