Sandy Beach SM0055-WA89 Brushed Chrome Bath Tap Filler Instruction Manual

Sandy Beach SM0055-WA89 Brushed Chrome Bath Tap Filler

Installation and operation instructions

Installation Notice

1. Please ensure all pieces are clean of debris.
2. After installation, test to ensure there are no leaks. Illustration A.

Illustration A

Note: Once assembled, fill the bath with water, and check for leaks.

• Overflow hole:
• Indicated as a hole on the bathtub’s side above the water level.
• Water level:
• Shown as the level water reaches, indicated to be higher than the overflow hole.
• Bathtub:
• Depicted with textured shading, containing water.
• Plug with washer:
• Located at the bottom of the bathtub to hold water.

Figure I

• Water outlet:
• Labelled (1), connected to the overflow hole of the bathtub.
• Foam washer:
• Labelled (2), situated between the water outlet and the bathtub.
• Silicone washer:
• Labelled (3), placed adjacent to the foam washer.
• 3-way main pipe:
• Labeled (4), central component of the setup.
• Rubber washer:
• Labeled (9), fits onto part 11 below the bathtub’s surface.
• Paperboard washer:
• Labeled (10), placed beneath the rubber washer.
• Clic-Clac Bath waste:
• Labelled (11), the waste component was installed in bath outlet B.

Figure II

• Illustrates the assembly of the water outlet, foam washer, silicone washer, 3-way main pipe, and out-flow elbow with labelled parts and directional arrows indicating the order of assembly.

Figure III

• Shows the clic-clac bath waste assembly with plastic pipe, plastic nut, paperboard washer, and connection to hole C, highlighting the importance of inserting the plastic pipe at least 10mm into hole C and tightening the plastic nut fully.

Specifications

FAQ

• What should I do before installing the product?
• Ensure that all pieces are clean of debris and read all instructions thoroughly.
• What are the water pressure and temperature limits for the product?
• The product can be used with water pressure between 0.5 to 4 bar and water temperatures from 0 to 90℃.
• How do I ensure there are no leaks after installation?
• After assembly, fill the bath with water and check for any leaks.
• What is the suitable thickness for the bathtub?
• The product is suitable for bathtubs with a thickness between 4-15mm.
• How tight should the connections be?
• Ensure that all parts are connected firmly and that the plastic nut is fully tightened to prevent leaks

Installation Notice,

1. Please ensure all pipes are clean of debris.
2. After installation, test to ensure there are no leaks. Illustration A.

Operation Notice

1. The product is suitable for use between water pressures 0.5 to 4 bar, and water temperatures 0-90°C.
2. Regularly clean the tap with a soft damp cloth.
3. Read all the instructions completely before proceeding.
4. The product is suitable for bathtub thickness 4-15mm.

Installing steps,

1. As demonstrated in Figure I, parts 1,2,3, should be separated from the 3-way main pipe(4).

2. As demonstrated on Figure Il, parts 3, and 2 are to be connected to the main pipe(4) in order, then taken through hole A (overflow) of the bath. Then tighten part 1 on the surface of the bath (take care when adjusting the direction of the water outlet slot).

3. Connect the top of part 5 to the 3-way pipe. The tail of part 5 connects with part 6 inlet tube.

4. Install part 11 Clic-clac Bath Waste onto bath outlet B.

5. As per Figure III, tighten parts 8,9,10 onto the plastic main pipe, then connect to part 11 clic-clac bath waste
   ( Note part No.7 plastic pipe should be inserted into hole C by at least 10mm, and at the same time make sure no.8 plastic nut is fully tightened).

6. Turn on the water supply valve and handle to check all the joints to ensure there is no leaks.

Illustration A

Note: Once assembled, fill the bath with water, and check for leaks.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>