BOSCH GKP 200 CE Professional Glue Gun Instruction Manual

: June 15, 2024
: Bosch

Table of Contents

Safety instructions
Product Description and Specifications
Operation
Maintenance and Service
Feature
CUSTOMER SUPPORT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BOSCH GKP 200 CE Professional Glue Gun

Safety instructions

Read all the safety information and instructions. Failure to observe the safety information and follow instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not allow persons unfamiliar with the glue gun or the instructions to operate the glue gun.
This glue gun is not intended for use by children and persons with physical, sensory or mental limitations or a lack of experience or knowledge. Otherwise, there is a risk of operating errors and injuries.
This glue gun can be used by children aged 8 or older and by persons who have physical, sensory or mental limitations or a lack of experience or knowledge if a person responsible for their safety supervises them or has instructed them in the safe operation of the glue gun and they understand the associated dangers. Otherwise, there is a risk of operating errors and injuries.
Supervise children. This will ensure that children do not play with the glue gun.
Children must not be allowed to clean and perform maintenance on the glue gun without supervision.
Always check the glue gun, cables and plugs before using the tool. Do not open the glue gun yourself, and have it serviced only by a qualified repair person using only original replacement parts. Damaged glue guns, cables and plugs increase the risk of electric shock.
Do not leave the glue gun unattended.
Do not expose the glue gun to rain or wet conditions.
Water entering a glue gun will increase the risk of electric shock.
If operating the glue gun in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
Do not throw the glue stick into fire.
Safely place the glue gun down after use and let it cool completely before packing it away. The hot nozzle can cause damage.
The plug for the glue gun must match the outlet. Never modify the plug in any way. Unmodified plugs and matching outlets will reduce the risk of electric shock.
Do not misuse the cable, for example for carrying, hanging or unplugging the glue gun. Keep the cable away from heat, oil, sharp edges and moving parts.
Damaged or entangled cords increase the risk of electric shock.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place by an authorised customer service agent. The replacement plug should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible shock hazard and should never be inserted into a mains socket elsewhere.
Do not touch the nozzle while it is hot. There is a risk of burns.

Product Description and Specifications

Please observe the illustrations at the beginning of this operating manual.

Intended Use
The glue gun is intended for solvent-free gluing of materials such as paper, cardboard, cork, wood, leather, textiles, foam materials, plastic (except PE, PP, PTFE, Styrofoam® and plasticized PVC), ceramics, porcelain, metal, glass and stone.

Product Features
The numbering of the product features refers to the illustration of the glue gun on the graphics page.

Heat shield
Nozzle
Support bracket
Feed trigger
Charging station a)
Mains cable
Power indicator
Glue stick a)

a ) Accessories shown or described are not included with the product as standard. You can find the complete selection of accessories in our accessories range.

Technical Data

Glue gun		GKP 200 CE
Article number		0 601 950 7..

Rated power input
– Heating| W| 500
– Keeping the glue gun warm| W| 30
Heat-up time| min| 4
Gluing temperature| °C| 200
Gluing capacity| g/min| 30
Glue stick diameter| mm| 11
Glue stick length| mm| 45−200
Weight according to EPTA‑Procedure 01:2014| kg| 0.40
Protection class| |

The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Operation

Starting Operation

Pay attention to the mains voltage! The voltage of the power source must match the voltage specified on the rating plate of the glue gun.

Switching On and Off
To switch on the glue gun, plug the mains plug into a plug socket.
Allow the glue gun to heat up for approx. 7 min before starting work. To do this, set the glue gun down on the support bracket (3).
To switch off the glue gun, remove the mains plug from the plug socket.

Safely place the glue gun down after use and let it cool completely before packing it away. The hot nozzle can cause damage.

Continuous Operation
The glue gun can be operated continuously when the mains plug is plugged in. The power indicator (7) must light up.
During breaks from work, set the glue gun down on the unfolded support bracket (3).

Cable-Free Operation
It is possible to work without cables in conjunction with the charging station (5) (accessory).
If the discharged adhesive becomes more viscous, heat up the glue gun again in the charging station.

Working Advice

Keep people and animals away from the hot adhesive and the nozzle tip. Adhesive and nozzle tip will heat up to approx. 200 °C, posing a risk of burns. If hot adhesive comes into contact with skin, immediately hold the affected area under a stream of cold water for several minutes. Do not try to remove the hot adhesive from the skin.
Only use adhesives that have been recommended by the manufacturer of the glue gun and that are suitable for the processing temperature.
Adhesive bonds can become unstuck when they are affected by moisture or heat.
Remove the mains plug for longer work breaks.
The glue gun can also be used when it is switched off after heating using the heat accumulator. If the discharged adhesive becomes more viscous, plug the mains plug back into the plug socket.

Preparing for gluing
The bonding locations must be clean, dry and free from grease.
The materials to be glued together and the work surface must not be easily ignited or flammable.
Test whether heat-sensitive materials are suitable beforehand on a sample workpiece.

The ambient temperature and the workpieces to be glued must not be colder than +5 °C and not warmer than +50 °C.
Materials that cool the adhesive down quickly should be warmed first with a hot air gun.

Gluing
Allow the glue gun to heat up.
Push the glue stick (8) suited to the material into the glue gun from behind.
Apply moderate pressure to the feed trigger (4).
Apply the adhesive to a single side.
Press the materials you wish to glue together against each other for around 10 to 30 seconds immediately after applying the adhesive. It is still possible to correct the bonding location at this point.
The bond is stable after approx. two minutes of cooling time.
Set the glue gun down on the support bracket (3) in between gluing processes.

Make sure you do not come into contact with the hot adhesive. Use a silicone mat to press permeable materials together.
Changing the nozzle
The nozzle (2) can only be removed when it is hot. To do so, heat up the glue gun for approximately 4 min.
Wear protective gloves when changing the nozzle.
Only hold the heated nozzle by the heat shield (1).
Touching the hot nozzle tip poses a risk of burns.
Fasten the new nozzle (2) until it is hand-tight.
Do not use flammable solvents to clean the bonding locations. The hot glue could ignite any solvent residue or release hazardous fumes.
Adhesive residue on clothing cannot be removed.
The bonding locations can be painted.
Application tips
** Material/workpiece| Recommendation**
---|---
Long workpieces with large surface areas| Apply adhesive in dots
Flexible materials (e.g. textiles)| Apply adhesive in lines

Maintenance and Service

Maintenance and Cleaning

Pull the mains plug out of the plug socket before carrying out any work on the glue gun.
Keep the glue gun clean to ensure effective, safe operation.

In order to avoid safety hazards, if the power supply cord needs to be replaced, this must be done by Bosch or by an after-sales service centre that is authorised to repair Bosch power tools.
After the adhesive has hardened, you can remove it with a blunt object. Do not use solvents when cleaning. If necessary, the bonding locations can be unstuck again by applying heat.
An inserted glue stick (8) must not be removed from the rear of the glue gun. This is to prevent damage to the glue gun.

An inserted glue stick (8) must not be removed from the rear of the glue gun. This is to prevent damage to the glue gun.

After-Sales Service and Application Service
Our after-sales service responds to your questions concerning maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on spare parts at: www .bosch-pt.com
The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.
In all correspondence and spare parts orders, please always include the 10‑digit article number given on the nameplate of the product.

Feature

Disposal
The glue guns, accessories and packaging should be sorted for environmental- friendly recycling.
Do not dispose of glue guns along with household waste!

Only for EU countries:
According to the Directive 2012/19/EU on waste electrical and electronic equipment and its transposition into national law, electrical and electronic equipment that are no longer usable must be collected separately and disposed of in an environmentally correct manner.
If disposed incorrectly, waste electrical and electronic equipment may have harmful effects on the environment and human health, due to the potential presence of hazardous substances.

Only for United Kingdom:
According to The Waste Electrical and Electronic Equipment Regulations 2013 (SI 2013/3113) (as amended), products that are no longer usable must be collected separately and disposed of in an environmentally friendly manner.

CUSTOMER SUPPORT

Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com