HOBBYWING XERUN 3652 DRX-8500KV Sensored Brushless Motor User Manual

HOBBYWING XERUN 3652 DRX-8500KV Sensored Brushless Motor

Product Information

• Specifications:
  • Model: XERUN 3652 DRX-8500KV, XERUN 3652 DRX-9500KV, XERUN 3662 DRX-6500KV
  • KV: 8500KV, 9500KV, 6500KV
  • LiPos: 2S
  • No-load Current (A): 8.2A, 8.6A, 8.0A
  • Diameter/Length (mm): =36mm(1.42in) L=53mm(2.09in), =36mm(1.42in) L=63mm(2.48in)
  • Shaft Diameter/Length (mm): =3.175mm(0.13in) L=14.5mm(0.57in)
  • Bearing size (mm): FrontD9D4T4 RearD8D3T4, FrontD11D5T5 L=18.5mm(0.73in) RearD8D3T4
  • Weight (g): 177g, 187g, 240g
  • Applications: 1/10 Drag Racing
• Installation & Connection:
  • Installation of the motor: There are 6 motor mounting holes in M3 specification, and the mounting holes are 5mm in depth. Before installing the motor on the vehicle, please carefully confirm whether the length of the screws is appropriate to avoid damaging the motor due to excessive length.
  • How to Connect the Motor to an ESC: When connecting the motor and ESC, please pay attention to the marked three-phase position of A, B, and C. Ensure that the three wires of the motor and ESC are connected in the correct order: wire A of the ESC matches wire A of the motor, wire B of the ESC matches wire B of the motor, and wire C of the ESC matches wire C of the motor. Connecting them incorrectly can result in abnormal operation and damage to the ESC and motor. Also, connect the sensor cable to the motor and ESC.
  • Inspection: Before powering on the ESC, please check the motor installation and the order of all connections.
• Gearing:
  • Reasonable selection of gear ratio is very important. Improper gear ratio may cause damage. You can select the gear ratio according to the following points:
  • The operating temperature of the motor
• Assembly and Disassembly:
  • For the motor to have a longer service life and higher efficiency, we suggest regularly checking the bearing and cleaning the dirt in the motor.
  • The specific time depends on the frequency of using the motor and the site conditions.
  • When installing, please follow the steps in the assembly drawing provided. When disassembling, follow the reverse steps.
• FAQ:
  • Can I use this motor for other applications besides 1/10 Drag Racing?
  • No, this motor is specifically designed for 1/10 Drag Racing applications.
  • What should I do if the motor gets too hot during operation?
  • If the motor gets too hot, you should check the gear ratio and adjust it if necessary. Running the motor with an improper gear ratio can cause overheating.
  • How often should I clean the motor and check the bearing?
  • The frequency of cleaning the motor and checking the bearing depends on the frequency of use and the conditions in which the motor is operated.
  • We recommend regularly inspecting and cleaning the motor to ensure optimal performance.

INTRODUCTION

Thank you for purchasing this HOBBYWING product!

• Please read this declaration carefully before use, once you use the product, we will assume that you have read and agreed with all the content.
• Brushless power systems can be very dangerous and any improper use may cause personal injury and damage to the product and related devices, so please strictly follow the instructions during installation and use.
• Because we have no control over the use, installation, or maintenance of this product, no liability may be assumed for any damages or losses resulting from the use of the product.
• We do not assume responsibility for any losses caused by unauthorized modifications to our product.
• Besides, we have the right to modify our product design, appearance, features and usage requirements without notification.
• We, HOBBYWING, are only responsible for our product cost and nothing else as a result of using our product.
• Regarding the possible semantic difference between two different versions of the declaration, for users in mainland China, please take standard.

Warnings

• Please carefully check the power devices and manual of the car frame to ensure the power pairing is reasonable. Avoid incorrect pairing to overload and damage the motor.
• Always wire up all the parts of the equipment carefully. If any of the connections come loose as a result of vibration, your model RC may lose control.
• Never apply full throttle if the pinion is not installed. Due to the extremely high RPMs without load, the motor may get damaged.
• Never allow the motor case to get 100 degrees Celsius (212 degrees Fahrenheit) because the magnets may be demagnetized by high temperatures.

Features

• Ultra-high rpm, superpower, specially designed for Drag Racing.
• The motor case and end cover are of a big opening structure, providing the best heat dissipation effect for the motor.
• Dual sensor interface design to meet various wiring/layout requirements.
• Widened and thickened copper bar design provides a guarantee for large current applications.
• The rotor adopts a steel sleeve explosion-proof design, which withstands ultra-high rpm running conditions.

Specifications

XERUN 3652 DRX

XERUN 3662 DRX

Installation & Connection

1. Installation of the motor
   • There are 6 motor mounting holes in M3 specification, and the mounting holes are 5mm in depth, before installing the motor on the vehicle, please carefully confirm whether the length of the screws is appropriate, so as not to damage the motor due to excessive length.
2. How to Connect the Motor to an ESC
   • When connecting the motor and esc, please pay attention to the marked three-phase position of A, B and C to ensure that the three wires of the motor and esc are connected in the order that, wire A of the esc matches wire A of the motor, wire B of the esc matches wire B of the motor, wire C of the esc matches wire C of the motor. Otherwise, it cannot run normally and even damage the esc and motor. And then connect the sensor cable to the motor and ESC.
3. Inspection
   • Before powering on the esc, please check the motor installation and the order of all connections.

Gearing

Reasonable selection of gear ratio is very important. Improper gear ratio may cause damage. You can select the gear ratio according to the following points!

1. The operating temperature of the motor
   • The motor temperature should be lower than 100 degrees Celsius (212 degrees Fahrenheit) in operation.
   • High temperature may cause the magnets to get demagnetized, the coil to melt and short circuit, and the ESC to get damaged.
   • A proper gearing ratio can effectively prevent the motor from overheating.
2. The principle of selecting gear ratio
   • To avoid the possible damage to ESC and motor caused by the overheating, please start with a small pinion/a big FDR and check the motor temperature regularly.
   • If the motor and ESC temperature stays at a low level during the operation, you can change a larger pinion/a lower FDR and also check the motor temperature regularly to ensure that the new FDR is suitable for your vehicle, local weather and track condition.
   • ( Note: For the safety of electric devices, please check the ESC and motor temperature regularly.)

Assembly and Disassembly

• In order for the motor have longer service life and higher efficiency, we suggest to regularly check the bearing and clean the dirt in the motor.
• The specific time depends on the frequency of using the motor and the site conditions.
• When installing, please follow the steps in the following assembly drawing; when disassembling, follow the reverse steps.

Parts List

• SHENZHEN HOBBYWING TECHNOLOGY Co., LTD.
• 101-402 Building 4,
• Yasen Chuangxin Hi-tech Industrial Park,
• 8 Chengxin Road,
• Baolong Industrial Town,
• Longgang District,
• Shenzhen, China.
• November 22, 2023
• HW-SMB575DUL00

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>