MiraScreen Q9R2 Wireless HD Transmitter and Receiver Kit User Manual

MiraScreen Q9R2 Wireless HD Transmitter and Receiver Kit

Specifications

• Size: 100*57mm
• Wireless HD Transmitter & Receiver Kit
• User manual Ver. A 1.0

Product Information

The MiraScreen Wireless HD Transmitter & Receiver Kit is a plug and play device that allows you to wirelessly transmit HD signals between devices. It provides a convenient way to connect and stream content from one device to another without the need for cables.

Pairing Instructions

The product comes pre-paired out of the factory, but in the case of pairing failure or if you need to repair the devices, follow these instructions:

Receiver [RX] Function Button:

• * Press and hold the receiver function button for 10 seconds.

  • A black screen will appear and restart.
  • The factory settings will be restored.

Product Usage Instructions

Transmitter [TX] – Function Button

The transmitter function button allows you to control the
connection and pairing status. The indicator light on the
the transmitter provides visual feedback on the connection status.

Transmitter Indicator Status

• Slow Flash : Disconnected
• Fast Flash : Pairing
• Always On Connected

Power Supply

Please make sure that the power of the computer is sufficient. If the power supply of the computer is insufficient or HD is unable to supply power, please connect the transmitter to the power adapter or Micro power supply port (Voltage above 5V, current above 2A).

Pairing Process

1. Press the receiver function button for more than 3 seconds.
2. A prompt will appear on the interface: “Release the button to pair with Ezcast TX.”
3. Wait for the transmitter to enter pairing mode.
4. Press the transmitter function button for more than 5 seconds.
5. The indicator will flash for pairing.
6. Wait for the transmitter indicator to be always on, indicating that the connection is successful.

FAQ

Q: How to restore factory settings?

A: When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and restart, the factory settings will be restored.

Q: Can devices without an HD interface be used?

A: Yes, please use the device with an HD interface converter.

Q: How to enter privacy mode?

A : Tap the transmitter function button to disconnect or reconnect.

Preface

Thank you for purchasing the MiraScreen products, For optimum operation, please read this manual carefully before use.

Connection Diagram

Hardware Casting

1. Connect the HD port of the receiver to the video input port of the display device such as the monitor or TV.
2. Connect the Micropower supply port of the receiver to the charging cable and plug it into the power adapter ( Voltage above 5V, current above 2A). Turn on the Receiver power switch.
3. Adjust the HD Signal source of the monitor or TV to the corresponding HD port until the boot screen is displayed.
4. Connect the transmitter to the computer or other devices With HD video output function. After the indicator Light enters the fast flash state, Wait for ten seconds to complete Casting.

• Please make sure that the power of the computer is sufficient. If the power supply of the computer is insufficient or HD is unable to supply power, please connect the transmitter to the power adapter or Micro power supply port ( Voltage above 5V , current above 2A )

Pairing Instructions

The product has been paired out of the factory. In case of pairing failure due to improper operation or other circumstances during use, it is necessary to restore and re-pair the device as follows

1. Please Press the receiver function button for more than 3 seconds, and the prompt will pop up on the interface:  Release the button to pair With Ezcast TX. Wait for the transmitter to enter pairing mode
2. Press the transmitter function button for more than 5 seconds, the indicator will flash for pairing, and Wait for the transmitter indicator to be always on, indicating that the connection is successful.

Problem-solving

• Q: How to restore factory settings?
• A: When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and restart, the factory settings will be restored.
• Q: Can devices without HD interface be used?
• A : Yes, please use the device with an HD interface converter.
• Q: How to enter privacy mode?
• A: Tap the transmitter function button to disconnect or reconnect.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>