Ashland CN ASH . FT NOBLE FIR Artificial Christmas Tree Instruction Manual

Ashland CN ASH . FT NOBLE FIR Artificial Christmas Tree

Product Information

Specifications

• Model: CN ASH 7.5 FT NOBLE FIR #112
• SKU: 10711456

Important Safety Instructions

1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. Do not use seasonal products outdoors unless marked as suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
3. This seasonal use product is not intended for permanent installation or use.
4. Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
5. Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
6. Do not let lamps rest on the supply cord or any wire.
7. Unplug the product when leaving the house, when retiring for the night, or when not in use for an extended period.

Use and Care Instructions

1. When the product is placed on a live tree, ensure that the tree is well-maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
2. If the product is placed on a tree, make sure that the tree is well-secured and stable.
3. Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
4. When storing the product, carefully remove it from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
5. When not in use, store the product neatly in a cool, dry location protected from sunlight.

User Servicing Instructions

Replace the fuse

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Open the fuse cover by sliding open the fuse access cover on top of the attachment plug towards the blades.
3. Remove the fuse carefully.
4. Risk of fire. Replace the fuse only with a 3 Amp, 125 Volt fuse (provided with the product).
5. Close the fuse cover by sliding the fuse access cover on top of the attachment plug.
6. Risk of fire. Do not replace the attachment plug. It contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Replace the lamp

1. Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
2. Unlock the burned-out LED lamp by lifting the hook.
3. Pull the lamp and plastic base straight out of the lampholder.
4. Replace the lamp with only a 3.0 Volt, 20mA, push-in type LED lamp (provided with the product). Always match the hook to the tab.
5. Lock the hook of the lamp base by pushing the lock down into the tab.

CAUTION

To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 Volt, 20 mA lamps only.

If the new lamp base does not fit in the lampholder, follow the steps below before step 4:

1. Pull the reflector out.
2. Remove the base of the burned-out lamp by straightening the lamp leads and gently removing it.

FAQ

• Q: Can I use this product outdoors?
• A: This product is suitable for indoor use only unless specifically marked as suitable for indoor and outdoor use. If using it outdoors, make sure to connect it to a Ground Fault Circuit Interrupting (GFCI) outlet and consult a qualified electrician if needed.
• Q: Can I leave the product plugged in overnight or when I’m away from home?
• A: It is recommended to unplug the product when leaving the house, when retiring for the night, or when not in use for an extended period to ensure safety and conserve energy.

Before You Begin

IMPORTANT SAFETY INSTRUCTIONS

• When using electrical products, basic precautions should always be followed including the following:

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

• Do not use seasonal products outdoors unless marked as suitable for indoor and outdoor use.
• When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet.
• If one is not provided, contact a qualified electrician for proper installation.
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
• Do not let lamps rest on the supply cord or any wire.
• Unplug the product when leaving the house, when retiring for the night, or if left unattended.
• This is an electric product – not a toy! To avoid the risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string.
• Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
• Do not cover the product with cloth, paper or any material not part of the product when in use.
• This product is equipped with push-in type lamps. Do not twist lamps.
• This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Also, unplug any additional strings or products that may be attached to the product. Replace the fuse as per the User
• Servicing Instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
• Read and follow all instructions that are on the product or provided with the product.
• SAVE THESE INSTRUCTIONS.

Use and Care Instructions

• When the product is placed on a live tree, the tree should be well-maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
• If the product is placed on a tree, the tree should be well-secured and stable.
• Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
• When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
• When not in use, store neatly in a cool, dry location protected from sunlight.

User Servicing Instructions

Replace the fuse

• Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on cord.

• Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.

• Remove the fuse carefully.

• Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).

• Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.

• Risk of fire. Do not replace the attachment plug. Contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Replace the lamp

1. Grasp plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on cord.
2. Unlock the burned-out LED lamp by lifting the hook.
3. Pull the lamp and plastic base straight out of the lampholder.
4. Replace lamp with only 3.0 Volt, 20mA, push-in type LED lamp (provided with product). Always match the hook to the tab.
5. Lock the hook of the lamp base by pushing the lock down into the tab.

CAUTION
To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 Volt, 20 mA lamps only.
If the new lamp base does not fit in the lampholder, follow the steps below before step 4.

• Pull the reflector out.
• Remove the base of burned-out lamp by straightening the lamp leads and gently pull the lamp out.
• Thread leads of the new lamp through holes in the old base with one lead in each hole.
• After the lamp is fully inserted into the base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lampholder (always match the long lead of the new lamp to the hook of the lamp base).
• Insert the reflector into the base.

CAUTION

1. Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product.
2. To reduce the risk of fire and electric shock: a) Do not install on trees needles, leaves or branch coverings of metal or materials that look like metal, and b) Do not mount or support strings in a manner that can cut or damage wire insulation.

Model No. CHL-036S

Assembly / Operation Instructions

CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE BEFORE ASSEMBLING OR DISASSEMBLING.

Assembling the tree stand

1. Choose a location near a wall outlet.
2. Open the stand to a 90-degree angle until the hole lines up with the hole on the tube.
3. Screw an eye bolt into the hole.

Assembling the tree

Please remove protective covers from the base of the pole for each tree section before assembling.

1. Carefully insert the bottom section (C) of a tree into the tree stand and tighten the screw. (See Fig. 1)
2. Insert the middle section (B) of the tree into the bottom section (C). (See Fig. 2)
3. Insert the top section (A) into the middle section (B). (See Fig. 3)
4. Allow branches to fall into place or gently pull branches up and out. When adjusting branches be sure that all wires are free of branch hinges. (See Fig. 4)
5. Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one at the centre of the main stem. Repeat the pattern for each branch. (See Fig. 5)
6. Plug the well-connected power cord from the tree section (C) into a proper outlet.

TROUBLESHOOTING TIPS

If The Tree Does Not Light

1. Ensure that all tree sections are plugged into each other and that the tree is plugged into the wall outlet.
2. Check for the blown fuse at the power cord plug. Replace as needed with the replacement fuses provided.
3. Check for loose, broken, or missing bulbs and replace them as needed with the replacement bulbs provided.

Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a spare rivet (D).

1. Place the branch into the slot of the bracket.
2. Insert a spare rivet (D) through the hole and use diagonal pliers (not included) to crimp the rivet (D). (See Fig. A)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>