ZENDit WIR404B Wireless 4 Channel Receiver User Guide

June 4, 2024
ZENDit

ZENDit WIR404B Wireless 4 Channel Receiver

overview

The entire range includes single or multi (2, 3 or 4) button key fobs in either a white or black finish with a selection of key-rings and clips, compact wall mount push button key pads and 1 or 4 channel
Full Instruction Manual receivers with control buttons too. Dual channel key pads are a useful addition to the range allowingafixed access pad to activate the open ing of a door or gate without the
riskof personnel losing or forgetting their keys.

User Information

  • Must be installed in a clean, dry environment where it will not be exposed to high https:systemg.comDE temperatures, moisture or excessive dust.
  • Imanual/xWIR301B.pdf
  • Do not touch the products or any connections with wet hands.
  • Ensure the power is switched off f the receiver or remove batteries if not in use for a long period of time.
  • There are no user serviceable parts in the products attempting to repair the product will void the warranty.
  • Do not install or use the device if the connected cables are damaged.
  • Warranty is void if the serial number label is removed

Pairing Fobs & Receivers

Step 1
Press the Learn button on the receiver. The LED light on the front of the unit will turn red. For the 1 Ch WIR401 this is found on the side of the unit. On the 4Ch WIR404 it is positioned at the top of the PCB. Remove the cover by unscrewing the small locking screws on either side of the unit. The front panel can then slide up and off.

Step 2
Press Button 1 on the key fob Twice. The LED light on the receiver will fl ash and then turn off.
Note: When pairing a multi channel key fob all other channels are learnt automatically after learning channel 1. Channel 1 activates relay 1, channel 2 activates relay 2 and so on.

Pairing Key Pads & Receivers

Step 1

  • Press the Learn button on the receiver. The LED light on the front of the unit will turn red.
  • For the 1 Ch WIR401 this is found on the side of the unit.
  • On the 4Ch WIR404 it is positioned at the top of the PCB. Remove the cover by unscrewing the small locking screws on either side of the unit. The front panel can then slide up and off.

Step 2

  • Enter the password for channel 1 (Default 000000/6 Zeros) and then press Button A Twice on the key pad. The LED light on the receiver will flash and then turn off.
    Note: For changing or resetting passwords see the Password Management section in the full manual.

Operation

  • To trigger channel 1 enter the password Hold down Button A until the top left LED lights up.and then press Button A. The top left LED will flash when successful.

  • Enter the current password e.g. 000000 and press Button A. The second LED will then light up.

  • Likewise, to trigger channel 2 enter the password and then press Button B. The top right LED will flash when successful.

  • Enter the new password e.g. 123456 and press Button A. The third LED will then light up.
    Note: After entering the password, press Re-enter the new password e.g. 123456 and press either Button A or B within 4 seconds. Button A. The first three LEDs will then flash to confirm the password has been set. See the ful manual for more information on the Zendit product (use the link overleaf or scan the QR code)

  • All specifications are approximate. System Q Ltd reserves the right to change product specifications or features without notice. Whilst every effort is
    made to ensure that these instructions are complete and accurate, SystemQ Ltd cannot be held responsible for any losses, no matter how they arise,
    from errors or omissions in these instructions, or the performance or non- performance of the equipment referred to.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals