Master Sounds MK2 Radius DJ Mixer Instruction Manual
- June 15, 2024
- Master Sounds
Table of Contents
FOR MUSIC LOVERS, BY MUSIC LOVERS.
Radius 2
MK2
WELCOME TO THE FAMILY
Radius MK2 builds on the success of the previous generation model, adding to
its unique feature set with a 4/3 band isolator, variable Q HPF per channel,
add mix feature, 2 x headphone jack points, and individual auxiliary return
knob. Redesigned internal
circuitry offers increased fidelity with MasterSounds open, natural, and
dynamic sound.
Handmade in small batches via Union Audio in Rural Cornwall, England.
Radius MK2, it’s Radius on another level.
Built for discerning DJs.
IMPORTANT SAFETY INSTRUCTIONS
READ THE INSTRUCTIONS Read and retain these instructions for future
reference. Adhere to all warnings printed here and on the console and its
power unit.
COVERS Do not remove the power unit cover. Operate the console with its
cover correctly fitted. Refer servicing work to authorised personnel only.
MAINS POWER Connect the console power unit to a mains power supply only of the
type described in this user guide and marked on the unit. The power source
must provide a good ground connection. Do not remove or tamper with the ground
connection in the power cord. Use the power cord with a sealed mains plug
appropriate for your local mains supply as provided with the console. Route
the power cord so that it is not likely to be walked on, stretched or pinched
by items placed upon or against it. MasterSounds recommends the use of a mains
conditioner on all our DJ mixers.
INSTALLATION Install the console and its power unit in accordance with
the instructions printed in this user guide. Do not connect the output of
power amplifiers directly to the console. Use audio connectors and plugs only
for their intended purpose.
VENTILATION Ensure adequate ventilation around the console and its power
unit. Do not obstruct the ventilation slots or position the unit where the
airflow required for ventilation is impeded.
MOISTURE To reduce the risk of fire or electric shock do not expose the
equipment to rain or moisture or use it in damp or wet conditions. Do not
place containers of liquids on it, which might spill into any openings.
ENVIRONMENT Locate the units away from direct sunlight and any equipment
which produces heat, such as power supplies, amplifiers, and heaters. Protect
from excessive dirt, dust, heat, and vibration when operating and storing.
Avoid tobacco ash, drinks spillage, and smoke, especially that associated with
smoke machines. Do not mount the power supply on any surface subject to
resonance or vibration.
HANDLING To prevent damage to the controls and cosmetics avoid placing
heavy objects on the console surfaces, scratching the surface with sharp
objects, or rough handling and vibration. Protect the controls from damage
during transit. Use adequate packing if you need to ship the unit.
WHAT’S IN THE BOX
FRONT PANEL CONTROLS
- 4/3 BAND ISOLATOR The new 4/3 band ISOLATOR offers unrivaled performance and playability of the SUB / LOW / MID & HIGH FREQUENCIES from OFF to +7dBu.
- 4 WAY / 3 WAY This button illuminates red when pressed into the 3-way configuration, and by doing changes the 4-band ISOLATOR to 3 bands.
- AUX The AUX send level pot adjusts the amount of channel signal level sent to the aux mix buss (and onto an external FX unit). Fully clockwise the signal level is boosted by +10dBu, allowing for precise adjustment of FX signals.
- PRE The PRE button switches the AUX to send a feed from post-fader to pre-fader (i.e. set to pre-fader it will still send to the aux mix buss with the rotary fader down).
- TRIM The TRIM pot adjusts the input signal level from OFF up to a maximum of +10dBu, enabling accurate level matching between different musical sources.
- LINE/RIAA This button selects either the RIAA (Phono) level input in its top position, or the LINE input in the bottom position as indicated with screen-printed text.
- VARIABLE Q HPF The new Variable-Q high pass filter offers a natural roll-off at low frequencies, lending perfectly to mixing with the filters alone, but as the knob is rotated the Q automatically rises to provide that classic analogue swept filer sound, with high-pass filter frequency range of 15Hz to 1500hz.
- CUE Each CUE button routes the channel signal to the headphones. Pressing the CUE button illuminates the red LED. When CUE buttons are activated you can hear the selected CUE channels playing. When NO cue button is active there is no signal in the headphones.
- CH1 & CH2 ROTARY FADER Each channel has a large ROTARY FADER for precision control of its level when mixing. The rotary ranges from fully off when anti-clockwise to unity gain (0dB) when clockwise. For best performance operate these controls near to their fully clockwise position for normal music level.
- VU METERS TWO VALVE MK2 features two high-quality analogue VU (Volume Unit) meters, which accurately measure the left and right audio signals. The meters show the post-EQ sound level. An added feature of the VU Meters is that when driven over +6VU the meter will illuminate RED to warn against clipping. In SPLIT MODE the LEFT VU Meter indicates the cue signal level, and the RIGHT VU Meter indicates the MIX level, (see SPLIT below).
- RETURN The return rotary pot adjusts the return signal level of the channel AUX rotary pots, allowing precise control of the returned signal on one or multiple channels.
- PHONES Please take care when monitoring with headphones as excessive sound volumes can cause premature deafness. The ¼” jack headphone input is located on the front of the mixer as shown on the headphone graphic.
- SPLIT The SPLIT CUE button illuminates RED when activated and links to the CUE buttons and VU Meters. When the SPLIT CUE is active and a channel CUE is pressed, the mix buss level will be shown on the right meter, and the channel pre-fade signal (CUE) will be shown on the left meter, enabling you to balance the two levels. The Split button also sends the cued source to the Left headphone and the mix source to the Right headphone. SPLIT CUE is automatically disabled when the Channel CUEs are off, and the Meters and Headphones revert to monitoring the stereo master signal.
- ADD MIX The add mix knob controls the amount of stereo house mix sent to your cued track in the headphones. When the knob is rotated fully anti-clockwise only the cued track will be heard. Turning the knob clockwise increases the amount of house mix that can be heard in the headphones.
- MASTER The MASTER rotary pot adjusts the signal level sent to the Main Output XLRs (House Mix) ranging from off to +10dBu of gain. Set the control to approximately 1 o’clock for unity gain.
- BOOTH The BOOTH rotary pot adjusts the signal level sent to the Booth Output TRS Jacks (Monitor Mix) ranging from off to +10dBu of gain. Set the control to approximately 1 o’clock for unity gain.
- HEADPHONE JACK Radius MK2 offers the option of 1/4 jack headphone input or 1/8” mini jack.
REAR PANEL CONTROLS
- MASTER OUT Output level is +14dBu when the MASTER level control is fully clockwise and the VU meters read -4VU. The XLR output is designed to operate with balanced equipment such as powered monitor speakers and amplifiers.
- AUX SEND & RETURN/INSERT The AUX SEND & AUX RETURN system has ¼” TRS (balanced) jack sockets for connection to an external FX unit. The SEND is connected to the FX units’ input, and the FX units’ output is connected to the RETURN, (see USING THE EXTERNAL SEND & RETURN SYSTEM).
- INSERT ON BUTTON Reconfigures the aux return jacks as a mix buss Insert, giving the user unparalleled flexibility for FX integration at the press of a button (see USING THE EXTERNAL SEND & RETURN SYSTEM).
- GROUND POST Unscrew the knurled nut, attach the turntable(s) ground lead(s), and screw back into place without over-tightening the nut.
- RECORD OUT Twin RCA sockets enable the user to make a stereo recording of a performance. The overall volume of the master output does not affect the record-out function—this outputs at -6dBu. 6- BOOTH OUT The ¼” TRS (balanced) jack booth output feeds the DJ’s booth (local monitor) amplifier/loudspeaker system.
- POWER SWITCH “O” = OFF. Press the “–“ to power the mixer ON with the external power supply connected.
- POWER INPUT SOCKET Connect the external 18V power supply to the input socket as labeled on the rear panel. The power input socket has a twist & lock mechanism for use with our LinearPOWER supply upgrade.
- CH ONE & CH TWO Both CH1 & CH2 feature LINE & PHONO inputs which have twin (left & right) RCA phono sockets. The Phono Input provides gain and RIAA equalization for turntable cartridges, and the LINE inputs provide input for CD players.
STEP 1 Connect the Mixer Aux Send outputs to the FX unit inputs and
connect the FX unit’s outputs to the mixer Aux Returns. Set the FX unit to
unity gain.
STEP 2 Turning up the mixer channel send control feeds the channel signal
to the FX unit. This signal is processed by the FX unit and its output is fed
back into the mix, adding an echo, delay, reverb, or other effect to the track
that’s playing. Turning down the mixer channel send stops the channel signal
feeding to the FX unit and so also stops the effect. Turning up the mixer
channel send increases the level of FX.
STEP 3 Use the RETURN knob to finely adjust the level of signal returned
into the mixer via the AUX pots. You can adjust single or multiple channels
and AUX effects and balance the return through the RETURN knob. (Please note,
the RETURN knob does not work with MasterSounds FX units, as MasterSounds FX
uses our INSERT system as described below).
STEP 4 Normally the feed to the channel AUX send is also controlled by
the channel fader, so turning down the fader also turns down the level of FX.
However if the AUX send PRE button is pressed, the AUX send takes its signal
before the Channel Fader so the channel signal can be sent to the FX Unit even
if the fader is off. This can be a cool way to mix into a new track:
introducing a low level delay of the track you are about to mix into, before
mixing in the new track by bringing up the channel fader.
STEP 5 MIX INSERT – MasterSounds DJ mixers have a unique feature that
allows the aux return jack sockets to be reconfigured as a mix buss Insert
point, just by pressing the INSERT ON button. This allows you to run the
entire mix through an external FX processor or other devices, such as a
compressor, limiter, or graphic equaliser. With the button pressed the two ¼”
TRS Jacks become a conventional mixer Insert, with the Tip being the SEND, and
the Ring being the RETURN.
TECHNICAL SPECIFICATIONS
POWER REQUIREMENT
(Each mixer is supplied with a compact switch-mode power supply for anywhere
in the world and we supply the correct IEC lead for your country)
External Power Supply – Universal 90V – 265V AC 50/60Hz 18v 30W Max
DC Internal Power Rails – +/- 18V DC
AUDIO PERFORMANCE
THD+N – 0dBu Line In to Mix Out +4dBu = 0.008%
Frequency Response – 20Hz – 100kHz +/- 1dBu
Mix Noise – Line In to Mix Out Unity -81dBu unweighted.
Residual Output Noise -105dBu
Left/Right Crosstalk -78dB
Fader Shutoff – -80dB
RIAA accuracy 30Hz – 20kHz < +/- 1dB
HPF Range – 15Hz – 1500Hz
Maximum Output +27.5dBu
ISOLATOR
Isolator Cut / Boost – OFF to + 7dB
Isolator Crossover fc 4 Band- SUB: 110Hz, LOW: 210Hz, MID: 1500Hz, HIGH:
3000Hz
Isolator Crossover fc 3 Band- LOW: 650Hz, MID: 1500Hz, HIGH: 3000Hz
DIMENSIONS & WEIGHT
W = 230mm L = 190mm H = 84mm
Weight = 2.5KG
*Please Note: This is the Faceplate size.
Not including knobs, sockets, cabling, etc.
Packed Dimensions:
W = 350mm L = 260mm H = 180mm
Packed weight = 3.2KG
DIMENSIONS & WEIGHT
W = 230mm L = 190mm H = 84mm
Weight = 2.5KG
*Please Note: This is the Faceplate size.
Not including knobs, sockets, cabling, etc.
Packed Dimensions:
W = 350mm L = 260mm H = 180mm
Packed weight = 3.2KG
WARRANTY
MasterSounds warrants that the Mixer shall be free of defects in workmanship and materials for a period of twenty-four months from the date of purchase. In the event that the product fails to operate as intended, MasterSounds will repair or replace the product subject to the following conditions.
- That the failure was not due to improper installation, operation, cleaning or maintenance, accident, damage, misuse, abuse, or non-approved modifications to the Mixer.
- The warranty does not cover normal wear and tear or any other event, act, default or omission outside MasterSounds control.
- Faulty products must be returned to MasterSounds or an authorised service agent along with the original invoice or proof of purchase, and the mixer must be returned packed in the original shipping box. Please contact MasterSounds before shipping a faulty unit.
- The warranty applies only to the original purchaser and is not transferrable.
- At their sole discretion, MasterSounds may either repair the defective product or replace with an equivalent service exchange item.
- This warranty constitutes the purchaser’s sole remedy. MasterSounds shall not be liable for any other repair or replacement cost or any damage or loss directly or indirectly related to the malfunction of this mixer.
Pots & switches & crossfaders are warranted for 3 months from the date of
purchase.
MasterSounds VALVE Series complies with the European Electromagnetic
Compatibility directives 2014/30/EU and the European Low Voltage directives
2014/35/EU.
MasterSounds reserves the right to change specifications without notice. RADIUS
2 MK2 Operation Manual
Copyright © 2024 MasterSounds Audio. All rights reserved.
www.mastersounds.co.ukIf you experience any
issues, please contact us immediately – scan the QR codes below for our
support and, social channels.
|
---|---
https://mastersounds.co.uk/pages/support|
https://www.instagram.com/mastersounds/
COPYRIGHT 2023 MASTERSOUNDS AUDIO LIMITED
THE TANNERY BUSINESS HUB, WATER STREET, STOCKPORT, ENGLAND, SK1 2BP
Documents / Resources
|
Master Sounds MK2 Radius DJ
Mixer
[pdf] Instruction Manual
MK2 Radius DJ Mixer, MK2, Radius DJ Mixer, DJ Mixer, Mixer
---|---