dyson gen5detect Cordless Vacuum Cleaner User Manual

June 15, 2024
dyson

gen5detect Cordless Vacuum Cleaner

Product Information

Specifications:

  • Model: SV12
  • Version: 01
  • Product Number: JN.00000 PN.000000-00-00 00.00.00

In the Box:

  • Main body with attached battery and bin
  • Charger
  • Fluffy OpticTM cleaner head
  • Digital MotorbarTM cleaner head
  • Hair screw tool
  • Wand with Built-in dusting and crevice tool
  • Fabric and mattress tool
  • Stubborn dirt brush
  • Scratch-free dusting brush
  • Awkward gap tool
  • Light pipe crevice tool

Caring for Your Floors:

To ensure optimal cleaning and maintenance of your floors,
follow these steps:

  1. Choose the appropriate cleaner head for your floor type: Fluffy
    OpticTM cleaner head for hard floors and Digital MotorbarTM cleaner
    head for different floor types.

  2. Attach the selected cleaner head to the main body of the
    vacuum.

  3. Adjust the suction control slider on the cleaner head according
    to your cleaning needs.

  4. Move the vacuum across the floor, allowing the cleaner head to
    pick up dirt and debris.

  5. If using the Hair screw tool, activate the motordriven cleaning
    for smaller spaces.

Charging Your Machine:

To charge your vacuum, please follow these steps:

  1. Connect the charger to the power outlet.

  2. Attach the connector end of the charger to the charging port on
    the vacuum.

  3. The vacuum can be charged with or without a dock.

  4. Wait for the battery to fully charge before using the
    vacuum.

Changing Your Click-in Battery:

If you need to change the battery, follow these
instructions:

  1. Ensure the vacuum is turned off and disconnected from the
    charger.

  2. Press the release buttons on both sides of the battery to
    remove it from the vacuum.

  3. Insert the new battery into the vacuum until it clicks into
    place.

Emptying Your Bin:

To empty the bin, follow these steps:

  1. Ensure the vacuum is turned off and disconnected from the
    charger.

  2. Press the release button located on the bin to remove it from
    the main body.

  3. Hold the bin over a trash can and press the release button to
    open the bottom flap and release the debris.

  4. Clean any remaining dust or debris from the bin using a cloth
    or brush.

  5. Reattach the bin to the main body until it clicks into
    place.

Cleaning Your Bin:

To clean the bin, follow these steps:

  1. Remove the bin from the main body of the vacuum.
  2. Rinse the bin with water to remove any dirt or debris.
  3. Allow the bin to dry completely before reattaching it to the
    main body.

Clearing Blockages:

If you encounter a blockage in your vacuum, follow these steps
to clear it:

  1. Turn off the vacuum and disconnect it from the charger.

  2. Refer to the user manual for specific instructions on clearing
    blockages from different parts of the vacuum, such as the Digital
    MotorbarTM cleaner head, Hair screw tool, or tools.

  3. Use a cloth or brush to remove any debris or obstructions.

FAQ:

Q: Where can I purchase additional tools?

A: Additional tools can be purchased on the official Dyson
website at www.dyson.com.au or www.dyson.co.nz.

SV12 JN.00000 PN.000000-00-00 00.00.00 VERSION NO.01

User manual

Contents In the box Getting started The LCD screen Alerts Caring for your floors Charging your machine Changing your click-in battery Emptying your bin Cleaning your bin Clearing blockages

Image 11
Clearing obstructions from your Digital MotorbarTMcleaner head Clearing blockages from your Hair screw tool Washing your filter Washing your Fluffy OpticTMbrush bar Scratch-free dusting brush Awkward gap tool Cleaning your tools Looking after your machine

In the box
Your machine will come with one, or both, of the cleaner heads shown here.

Main body showing the bin and battery attached.

A soft fluffy brush bar housed within the cleaner head. There is an electrical connecter end that can attach to the end of the wand or directly to the machine.

A brush bar located inside the cleaner head and a suction control slider located on the front.

The charger is a one piece unit with the plug, connector end and cable.
Charger Charges your vacuum with or without a dock.

Vacuum cleaner with battery and bin attached
This tool has a combination of brush head and crevice tool together in one unit. The brush head slides down the crevice tool when needed.

Fluffy OpticTM cleaner head
A precisely-angled blade of light makes invisible dust visible on hard floors.

Digital MotorbarTMcleaner head
Dyson DLSTMtechnology monitors brush bar resistance and adapts power across different floor types. Hair removal vanes prevent tangling around the bristles.

A small cleaner head with an angled body housing the motor and an electrical connector to attach to the wand or directly to the machine.

Combination tool Two tools in one ­ wide nozzle and brush, for quick switching between cleaning and dusting tasks around your home or car.

A rectangular dock that needs to be fixed to a wall with screws.
Wall dock The Dyson cordless vacuum drops into the wall-mounted charging dock, ready for your next clean.

Dyson wand, with a Built-in dusting and crevice tool, convenient for on-the- spot cleans.

Hair screw tool Anti-tangle conical brush bar spirals hair off and into the bin. Motordriven cleaning for smaller spaces.

Wand with Built-in dusting and crevice tool Stored inside the wand is a ready- togo crevice tool for on-the-spot cleans.

Some tools may not be included. You can buy additional tools at www.dyson.com.au or www.dyson.co.nz.

A wide, triangular shaped nozzle.
Fabric and mattress tool Removes dust, dirt and allergens from mattresses and upholstery.
A short nozzle with stiff bristles on the underside.

With an elbow joint, fitted between the bin and the tool.
Low-reach adaptor Bends to comfortably reach down low. Engineered to clean further under low furniture by adjusting the wand angle up to 90°.
A plastic clip that attaches to the wand

Stubborn dirt brush Stiff nylon bristles dislodge ground-in dirt from coarse carpets, high traffic areas and car interiors.

Wand clip Clips to your vacuum’s
wand to hold tools.

The Scratch-free dusting brush has a head made of soft bristles for cleaning delicate surfaces.

The Awkward gap tool is long and slim, with a 22 degree twist, for cleaning tight gaps and hard-toreach places.

A flexible hose engineered from tough wire and durable plastic.

Pliable bristles and felt bumper strip on a narrow, tapered tool.

Scratch-free dusting brush Gentle on delicate surfaces. Self-cleaning ­ a rotating cuff keeps the soft bristles clear of dust.
A long tool with an angled end.
Light pipe crevice tool Crevice tool with LED lights lets you reach into dark, narrow spaces and see where you’re cleaning.

Awkward gap tool Long and narrow, with a 22° twist to clean car storage compartments, tight gaps and hard-toreach places.
A jointed connector that creates a flexible joint between the machine and the tool. It must be used in conjunction with a tool or cleaner head.

Extension hose Adds up to 61cm of flexible reach to any tool attachment, to clean up high or down low in your home or car.

Up-top adaptor Bends and locks at different angles. For effective cleaning in hard-to-reach high areas of your home.

Soft dusting brush Enclosed in a skirt of soft nylon bristles for gentle, vacuumassisted dusting of delicate objects and surfaces.

Getting started

Press the red button on the LCD screen to start the machine

Screen on the

100%

filter end of the

machine.

Location of the Selection button on the screen on the filter end of the machine.

cclliickk

Using the LCD screen

Finger pressing the selection button on the screen to move between power modes.
Power modes Your machine has three power modes for different tasks. Change power modes quickly using the silver Selection button.

Eco

The screen showing the machine set to Eco mode with a full battery in green to show that this will give the longest battery life of the three modes.

Eco mode Maximum run time for longer cleans all around your home.

cclliickk cclliickk

Auto

Med

Two screens showing the machine set to Auto mode and Med mode with a blue battery showing that this will give a medium length of battery life.

Auto and Med mode Medium mode for the optimum balance of power and run time. Attach your cleaner head or Hair screw tool to activate Auto mode. Suction power automatically adapts to dust levels.

Arrow showing the end of the wand connecting to the cleaner head.
cclliickk

Boost

The screen showing the machine set to Boost mode with a red battery to show that this will give the shortest battery life of the three modes.

Boost mode Designed for intensive spot cleaning of ground­in dirt.

Diagram showing the connection of the wand onto the main body, with the wand release button aligned with the top of the main body.
The screen, on the end of the main body, showing a graph of the sizing and counting of the dust particles.
Blue = high volume, continue cleaning White = medium volume, continue cleaning Green = low volume, move onto the next area
m 10 90 180 500
38:37
Shows you when your floor is clean A piezo sensor continuously sizes and counts dust particles at the inlet. Your machine categorises, counts and displays the amount of particles picked up. Bars will rise and fall depending on the amount of debris and dust detected ­ showing you in real-time when your area is clean.

The LCD screen

The Selection button on the screen being pressed.

Settings menu Control the settings on your machine using the Selection button. To enter the settings menu, press and hold the silver button until the menu screen appears. Press the silver button to move through the options within the settings menu.

Hold the button to open an option.

­ Language ­ Alerts ­ Serial numbers

In settings, the Alerts option allows you to set the onscreen alerts to On or Off.

For more information and support for your machine go online: www.dyson.com.au/support or www.dyson.co.nz/support

Alerts On

Language
Serial numbers

In the settings menu, the Language option allows you to select your screen’s language preference.
In settings, the third screen option allows you to view Serial numbers.

E

The Exit menu screen is the final option in settings.

Change language To change the language on your screen, press the Selection button and hold it until the language list appears. Release the button.
Tap the Selection button to scroll through the language list to your preferred language. Press and hold the button until the countdown ends.
A green tick will appear on the screen to show your language selection is complete.
To cancel your selection, release the button during the countdown.

Language

In the settings menu, the Language option allows you to select your screen’s language preference.

English Español

English
selected

Two screens, the first with the language list and then the tick screen to show that the language has been successfully changed.

Find your serial numbers You can find your serial numbers in the settings menu.
Press the Selection button to move through the settings sequence until you reach Serial numbers.
Press and hold the button to select this option.
Press the button to move through your serial numbers information.

Serial numbers
The Serial numbers screen is the option for searching for your serial numbers.

Run time countdown When the battery needs charging, your machine will pulse three times and a Low run time icon will appear on the screen.
Low run time will be in amber, or red when in Boost mode.
When your battery is empty, a red warning icon will appear on the screen.

The screen reads Low run time, surrounded by an amber circle, when the battery needs charging.

Low run time

Low run time
The screen reads Low run time, surrounded by a red circle, if the battery runs low while in Boost mode.

Battery health and Boost advice To get the best performance and life from your battery, use Eco or Auto/Med mode.
If you use Boost mode frequently, this message may appear, to help you conserve your battery life.

A red screen with an icon with a plug being connected to the power supply. This demonstrates the battery is empty and needs charging.
The battery health is shown on the batteries on the screen.

Exit settings menu

Low power modes maintain
battery health
Alert with a white heart icon, reads `Low power modes maintain battery health’.

An alert with three battery icons, large, medium and small. The first two coloured grey to indicate empty. The third is red, indicating very low battery.

E

Screen with `Exit menu’ wording and return icon.

Alerts
The alerts you might see are: Airway obstructed Your machine has a blockage that needs removing. Watch the animation to see which airways to check. Make sure your machine is turned off before removing a blockage.

Alert icon with Airway obstructed wording.

A pair of spectacles observing the bottom of a cleaner head is an obstruction warning directing you to investigate a blocked cleaner head.
Air way obstructed

High storage temperature Your machine is being stored in a place where the temperature is too high. Move your vacuum to a cooler place.
Cold temperature Your machine is too cold. Move your vacuum into a warmer environment and leave to warm up.
Non-Dyson battery A non-Dyson battery has been detected. If you are not aware that you are using a third party battery for your machine, this may be a counterfeit.

Alert icon with `High temperature detected’ wording.

High temperature
detected
A vaccum handle icon, surrounded by four three-pronged, red heat symbols, is an alert signalling your vacuum is too hot ­ and should be stored clear of a heat source.

Alert icon with `Machine too cold’ wording.

Machine too cold

Leave to warm up

Alert icon with `Leave to warm up’ wording.

Alert icon with `Non Dyson battery detected’ wording.

Non Dyson battery detected.

Use genuine parts to protect your machine

Alert warning icon reads `Use genuine parts to protect your machine’.

Alert icon with `Refer to compliance and…’ wording.

Refer to compliance
and…

…safety information

Alert icon with `…safety information’ wording.

Clean filter Your filter needs cleaning. Please refer to `Washing your filter’.
After cleaning, leave to dry for at least 24 hours before reattaching it to your machine.

Alert icon with `Filter needs cleaning’ wording.

Filter needs cleaning

Filter not sealed Your filter isn’t properly fitted. Twist your filter anti- clockwise and pull it away from your machine. Reattach to your machine, twisting it clockwise until it locks into place.

Alert icon with `Filter not sealed’ wording.

Filter not sealed

2+4h
Alert icon with a filter graphic and `24+’ reminds you to leave your filter to dry for 24hrs after washing.

Change alert settings You can turn the alert motor pulse off. Your motor will no longer pulse but run time alert information will continue to be displayed on the LCD screen when your machine needs your attention.
Turning off alerts will not turn off the blockage alert pulsing. This is to ensure you clear any blockages, preventing damage to your machine.
Make sure you have entered the settings menu. Tap the Selection button to move through the options within the settings menu. Press and hold the button to select the `Alerts’ option.
Tap the button until your selection is highlighted. Hold it down until the countdown ends and a tick appears on the screen. To cancel your selection, release the button during the countdown.

Alerts On
The Alerts screen allows you to choose On or Off.

On Off Exit
The Alert settings menu reads On, Off, Exit.

Learn more about your LCD screen. View video on your owner’s page.

Caring for your floors
Check that the underside of the cleaner head or tool is clean and free from any objects that may cause damage. Before vacuuming your flooring, rugs, and carpets, check the manufacturer’s recommended cleaning instructions. The brush bar on your machine can damage certain carpet types and floors. Some carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we recommend vacuuming without the motorised floor tool and consulting with your flooring manufacturer.
Charging your machine
You can use your machine immediately, or charge it partially, without the need to fully charge before first use.
Connect to the charger, either directly or in the dock. The blue LEDs on both sides of the battery will flash during charging. When the battery is fully charged, both LEDs will light for five seconds. Your battery is fully charged when the display shows 100%. Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery.

The charger connected from the power supply using the wall dock.
100%
The charger connected from the power supply directly into the front of the battery.

Changing your click-in battery
If you have additional click-in batteries, we recommend that you alternate the batteries to maintain even performance.
Removing your battery Push the Battery release button at the front of the battery unit, and slide the battery off your machine. Charge the battery.
Refitting your battery Align your battery with the handle and slide it in. Push firmly until it clicks into place.

Arrows showing the location of the Battery release button at the front of the battery unit, and the battery coming off the handle when the button is pressed. The battery is then shown being replaced on the base of the handle, clicking into place.
cclilcik

Emptying your bin
Empty as soon as the dirt reaches the MAX level ­ don’t overfill. Using your machine when the dirt is above the MAX line may affect the performance and require more frequent filter washing. Overfilling your bin could result in inaccurate readings on the particle graph. Make sure your machine power is turned off before removing your wand or releasing the bin.
Remove your wand Press the grey wand release button, on the top of the wand, and pull the wand away from the bin.
Release the dirt Hold the machine over the bin, pointing downwards. Firmly push the red bin release button. The bin will slide down, cleaning the shroud as it goes, and the bin base will open. The bin base won’t open if the red bin release button isn’t pushed down all the way.
Minimise dust contact Cover your bin tightly in a dustproof bag while you empty. Remove your bin carefully, seal the bag tightly and dispose.
Close the bin Push the bin base upwards until your bin and bin base click into place.

Illustration of the bin being emptied into a bag.
The bin lid closing with an audible click and the bin being pushed upwards with another click once it is fully in place.
cclliickk

Cleaning your bin
Remove your bin If you need to clean your bin, empty it as shown in the `Emptying your bin’ section.
Press the red button located on the bin runner to release the bin and slide your bin off the runner.
Clean your bin using a damp, lint-free cloth.
Make sure that your bin and seals are completely dry before refitting.
Your bin isn’t dishwasher safe and the use of detergents, polishes or air fresheners to clean your bin isn’t recommended, as it may damage your machine.

The bin being removed and the location of the bin release lever on the underside of the bin runner.

Refit your bin Insert the spine on to the bin runner.
Close your bin by pushing the bin base upwards until the bin and bin base click into place.

The bin being pushed back into position on the bin runner.

The bin base being closed as the bin is slid back onto its runner and into position.

cclliickk cclilcikk

Clearing blockages

Disconnect your machine from the charger before looking for blockages. Make sure your machine power is turned off and be aware of sharp objects. Leave your machine to cool down before looking for blockages. Don’t use your machine when looking for blockages as this could cause injury.
If your machine detects a blockage, the motor will pulse and you won’t be able to use your machine until the blockage has been cleared. If you try to use your machine when the motor is pulsing, it will automatically cut out.

With the bin removed, check for blockages, paying particular attention to the air inlet, located on the right­hand side of the machine just below the point where the bin joins the main body of the machine.

Check the main body Remove the bin and check for blockages in the main body of your machine.
Make sure any blockages are completely cleared and all parts are fitted before using your machine.

Check the wand and cleaner head Check the wand for blockages.
Check your cleaner head for blockages, following the instructions to remove the brush bar, where necessary.

Re­assemble your machine Refit all parts securely before using your machine.
Clearing blockages isn’t covered by your guarantee.

With the wand removed from the machine, check for blockages at both ends of the wand.
Turn the cleaner head over to check for obstructions on the brush bar and air inlet.

Clearing obstructions from your Digital MotorbarTMcleaner head
Your Digital MotorbarTMcleaner head doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions. Make sure your machine is disconnected from the charger and your machine power is turned off. Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.
Remove your brush bar Press the cleaner head release button on the end of the wand. Place the cleaner head upside down. Use a coin to unlock the end cap. Turn the end cap and remove it from your brush bar. Don’t wash the end cap. Slide your brush bar out of the cleaner head.
Look for obstructions Clear any debris from your brush bar. Check inside the cleaner head and remove any debris or blockages. Your Digital MotorbarTMcleaner head and brush bar aren’t washable. Wipe over with a damp lint-free cloth.

The lock located on the side of the cleaner head, is rotated 90° anti- clockwise to release the end cap and the brush bar can be removed.
Clear debris alert is an X-ray style graphic of a brush bar inside a cleaner head. A green arrow indicates brush bar being pulled out of the cleaner head to the right.

Refit your brush bar Push the end cap back on to your brush bar and slide it back into the cleaner head.
Turn the end cap 90° clockwise into the locked position.

The removal of the brush bars showing the lock in a horizontal position and the unlock symbol at 90° anti-clockwise and lock symbol at 90° clockwise.

Clearing blockages from your Hair screw tool
Your Hair screw tool doesn’t have a washable brush bar. To maintain optimum performance, check your brush bar regularly and clear any obstructions.
Make sure your machine is disconnected from the charger and your machine power is turned off.
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

Remove the cover and brush bar Remove the Hair screw tool from the wand or machine.
Push the base plate open. Press the red lever down to release the cleaner head cover.
Pull the cleaner head cover off the main body of the tool.

The location of the lever to release the brush bar is located at the back of the Hair screw tool.

Look for obstructions Pull your brush bar firmly to remove it from the main body.
Check and remove any obstructions from all three parts of your Hair screw tool.
Your Hair screw tool isn’t washable. Wipe over with a damp lint-free cloth.

Re­assemble the Hair screw tool Put your brush bar back into position and press firmly until it clicks back into position.
Check the red locking lever is in the unlocked position. Align the cleaner head cover with the guide on the main body. Push it down until it clicks into position.
Push the red locking lever up until it clicks into position and push the base plate back into place.

Slide the housing back on to the brush bar and push the lever on the back of the Hair screw tool upwards to lock.

Washing your filter
Wash your filter at least once a month to maintain optimum suction power. Important: your filter must be completely dry before putting it back into your machine. Your machine could be damaged if used with a damp filter. For more information and support videos for your machine visit: www.dyson.com.au/support or www.dyson.co.nz/support
Twist off Twist your filter anti-clockwise and pull it away from your machine.

The filter is located at the rear of your machine.

Tap Before washing your filter, tap it gently over a bin to remove any loose dust and debris.

Holding the filter by the hard, plastic end, tap the other end over the bin.

Wash Wash the pleated paper element of your filter first, under warm, running tap water, with the foam element facing downwards.
Next, wash the foam element of your filter with the foam element still pointing downwards.
Holding your filter on its side, run warm water over the outside of the foam element, gently rubbing your filter to remove the dirt.
Repeat washing until the water runs clear.

The `Wash your filter’ icon is a blue tap, running water over a filter below.

A tap running water over a filter, signifying rinsing foam from the filter.

Shake and dry Empty the filter and shake it firmly to remove excess water.
Keep shaking until there’s no water coming from the filter.
Place the filter on its end and leave to dry for at least 24 hours in a well- ventilated, warm place.
After cleaning your filter, thoroughly wash your hands using anti-bacterial soap.
Check that the filter unit is completely dry.
To refit, position the filter unit in place on the main body and twist clockwise until it clicks into place.
Don’t dry your filter in a dishwasher, washing machine, tumble dryer, oven, microwave or near a naked flame.
Important: Your filter must be completely dry before you put it back into the machine. Your machine could be damaged if used with a damp filter.

A hand holding the filter with the narrow end pointing downwards with droplets of water being shaken from the filter and again, with the end pointing downwards shaking water out.

Alert graphic with 24+ reminds you to leave your filter to dry for 24hrs after washing.

The filter is left to dry with the pleated filter end facing downwards.

Washing your Fluffy OpticTMbrush bar

Your FluffyTMOptic cleaner head has a washable brush bar. To maintain optimum performance, check and wash your brush bar regularly.
Make sure your machine is disconnected from the charger and your machine power is turned off.
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners.

Remove your brush bar Press the cleaner head release button on the end of the wand. Place the cleaner head upside down.
Push the end cap up fully and pull the brush bar out of the cleaner head.
Remove the end cap from the brush bar. Don’t wash the end cap.
Slide your brush bar out of the cleaner head.

The end cap is

1

located at the side

of the cleaner head.

Push this upwards to

unlock the brush bar.

Don’t wash the end

cap.

2

Wash and dry your brush bar Hold your brush bar under running water and gently rub to remove any lint or dirt.
Stand your brush bar upright as shown. Leave to dry completely for at least 24 hours.

The brush bar has an open end and a closed end. Stand upright, with the closed end facing upwards, to dry.

Refit your brush bar

3

Before refitting, check that your brush bar is completely dry.

Reattach the end cap to your brush bar.

The end cap should

Slide your brush bar into the cleaner head. Push the end cap back down to the closed position.

be attached to the

cleaner head at an

angle less than 90°,

2

any angle greater

1

than this will not allow

the end cap to close.

Cleaning your optic lens To maintain optimum performance, keep your lens clean. Only clean the lens when the cleaner head is not attached to your machine.
Use a soft, dry, lint-free cloth to wipe the lens.

Scratch-free dusting brush
Tool may not be included. Compatible with DysonGen5detectTM, Dyson V15 DetectTM, Dyson V12 Detect SlimTM, Dyson OutsizeTM, Dyson V11TM, Dyson Cyclone V10TM,Dyson V8TMand Dyson V7TMvacuums.
Step 1 Attach the Scratch-free dusting brush directly to your vacuum or to the extension hose for delicate cleaning.
Step 2 Switch on your vacuum with the extension hose, hold the vacuum with one hand and the Scratch-free dusting brush with your other, using a pencil-like grip.
Note: Don’t press the Scratch-free dusting brush too hard against surfaces. The ultra-soft bristles should be the only part of the tool that contacts surfaces.
Self-cleaning Step 1 When you notice dust starting to build up on the bristles during or after use, we recommend you use the built-in self-cleaning function.
Step 2 With your vacuum switched on, lift the Cleaning cuff until you hear a click, so it completely covers the bristles. Rotate it five times. This hygienically cleans the dust from the bristles and sucks it into the bin.
Step 3 After five rotations, move the cleaning cuff back down, until you hear a click. Your bristles are now dust-free.
Note: Only use the self-cleaning function when the Scratch-free dusting brush is attached directly to the vacuum.

The Scratch-free dusting brush, which has soft dusting bristles at the top and a solid base.

The Scratch-free dusting brush has a green arrow, pointing upwards, just above the area of the base that attaches to the vacuum or extension hose.
A section of the base, has been moved up to cover the bristles completely.

x5

The base of the attachment

is still covering the bristles,

twist base round 5 times

Awkward gap tool
Tool may not be included. Compatible with DysonGen5detectTM, Dyson V15 DetectTM, Dyson V12 Detect SlimTM, Dyson OutsizeTM, Dyson V11TM, Dyson Cyclone V10TM, Dyson V8TMand Dyson V7TMvacuums.
Step 1 Attach the Awkward gap tool directly to your vacuum.
Step 2 For cleaning standard surfaces, such as skirting boards, use the tool in its original (straight) position.
Step 3 If you are using the tool to reach a tight or awkward gap, rotate the tool to its 22° angle until you hear a click. This allows you to reach further and clean more.
Maintenance tip To clean, wipe the tool clean with a damp cloth.

A long, thin tool with an angled end.
Twist the base of the tool round until you hear a click.

Cleaning your tools
Don’t put any part of your machine in a dishwasher or use detergents, polishes or air fresheners. Wipe with a damp, lint-free cloth, without touching the connector end. Make sure your tools are completely dry before using. Some tools may not be included.

Combination tool

Scratch-free dusting brush

Awkward gap tool

Extension hose

Soft dusting brush

Stubborn dirt brush

Low-reach adaptor

Light pipe crevice tool Up-top adaptor

Fabric and mattress tool

Looking after your machine
To always get the best performance from your machine, it’s important to clean it regularly and check for blockages.
Look after your machine If your machine is dusty, wipe with a damp lint-free cloth. Check for blockages in the cleaner head, tools and main body of your machine. Wash your filter regularly and leave to dry completely. Don’t use detergents or polishes to clean your machine. Look after your battery To get the best performance and life from your battery, use Eco or Auto/Med mode. Your machine won’t operate or charge if the ambient temperature is below 5°C (41°F). This is designed to protect both the motor and battery. Your serial numbers You can find your serial numbers on your machine, battery, charger and in your screen settings. For more information and support for your machine go online: www.dyson.com.au/support or www.dyson.co.nz/support

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals