Qianghe FONEWE-B Bluetooth LED Strip Light User Manual
- June 15, 2024
- Qianghe
Table of Contents
Qianghe FONEWE-B Bluetooth LED Strip Light
Product Parameters
- LED type: 3535 RGB.
- APP control distance: within 1 OM.
- Working temperature:-2o·c -+45°C.
- Width of strip light: 8mm.
- Waterproof: No.
- Cuttable for LED strip lights: Yes, 8 leds every cut
Instructions
- Wipe the surface of the object clean, and keep the surface clean and dry.
- Remove the film of the LED strip lights.
- Press the LED strip lights on the object with your hand to make the LED strip lights and the object close together.
- Keep the surface clean and dry.
- Tear and Attach
APP Mode
This APP program requires that the minimum systems of your phones are Android
4.3 or iOS 9.0. No limit to mobile phone configuration. You can download the
APP by scanning the QR code on 1OS or Android systems. Use APPs with
scanning functions such as browsers to scan the QR code. Please open the APP
on your phone, by which you can connect one or more sets of LED strip lights
through Bluetooth and able to set group and control multiple LED strip lights.
Functions
-
In Adjust, can adjust the brightness and 16 million kinds of colours,
-
In the Style, there are 22 style modes, that can make colours change automatically and would keep changing even when the phone is disconnected from the LED strip lights.
-
ln the Music, the colours of LED strip lights dinge automatically according to the music rhythm, which is beautiful.
-
If the phone system is Android, the APP will automatically sync the songs that have been downloaded to your mobile phone.
-
If the phone system is iOS, you need to connect your mobile phone to the computer and use iTunes to import the songs fromthecomjXJ!to)OJrmobile phone. Then the APP will automatically sync the songs you have imported.
Notes : If you have any questions about music mode, please refer to APP ‘Settings- Help – Sync Music Guide’ in the APP interface. -
ln the Tape, colours adjust automatically based on the ambient sound, and the Phone Mic or Device Mic can be chosen.5.ln the Timing, the LED strip lights have a timer function. You can preset the time to turn on/off your LED strip lights. Then it will automatically turn on or off on time.
Notes: You need to pay attention to setting the timer mode. First, open the Timing of the APP, and then follow the prompts, slide up to select the device you want to set and then set your time according to your needs. -
Long-distance control without direction restriction and multiple controls are allowed.
-
LED strip lights have a memory function. When the LED strip lights are used again, they remember the last mode settings without having to repeat the settings.
-
Once connected, your phone will connect to the LED light strips automatically after you turn on your Bluetooth.
-
On the APP, in the Adjust, you can DIV your favourite colours. If you have not selected colours, you can also use the function of extracting colours from pictures.
-
First select the picture icon in the upper right corner, then after uploading the picture, extract your colours from the picture to set the colours of the LED strip lights.
-
ln ‘Settings – Background: you can also change the background picture of the APP. We provide 9 background pictures for your choice.
-
lf you have any questions about the APP, you can refer to the specific instructions in the ‘Settings- Help – User Guide’..
APP Notes
When two apps want to be connected to a strip lights controller at the same
time, there will be a situation where they cannot be connected. Please exit
one APP, close the application and enter the APP to connect
Happy lighting APP
When your device can’t connect the lights automatically, follow the steps below:
Android Methods:
Method 1: Click, ‘My Device’to refresh (on the top left corner), and the
device successfully connected with be displayed.
Method 2: If the first step fails, you need to exit the APP and close its
process in the background completely, then open it again.
Method 3: lf it still fails, you need to exit the APP and close its
process in the background completely, turn off the Bluetooth, then turn on the
Bluetooth, and open the APP again.
iOS Methods
Method: Exit the App, close its process in the background, and then open the
APP again. Bluetooth permission and Location Services: For iOS, only need
Bluetooth permission. For Android version< 12, to scan the Bluetooth, need to
allow ‘Location Services” and”Nearby devices’: For the Android version?12, to
scan the Bluetooth, only need to Allow the”Nearby devices. permission, not
need the”Location Services:
Setting Sensitivity of Controller
When you use Music or orTape functions, the change of led strip lights cannot change with the rhythm of the music, the problem you encountered may be that the sensitivity of the controller has been set low, so the sensitivity to sound is not sensitive. On the Tape, select the Device Mic, and click ‘to increase its sensitivity, You also can set the sensitivity of the controller through the controller’s.
Common Troubleshooting
The controller was connected to the power, but not light up:
- Check the input power supply: please use the power adapter that we equipped or other adapters with the same specification as ours. The input voltage must meet the voltage requirement of the LED strip lights. When the input voltage is lower than a requirement, the LED strip lights will not be turned on, while a higher voltage may damage the circuit. The output power of the adapter (KW value) must equal to, or higher than the power of the LED strip lights.
- Check whether the connector is connected correctly with the strip lights. Make sure each interface is connected correctly,
- Check whether the remote control is open.
Attention
- The LED strip lights must be connected correctly Based on the Installation guide.
- Led strip lights must be used underrated DC voltage
- The light strips are not waterproof, only suitable for indoor uses.
- Make sure the surface you are going to paste strip is clean and dry.
Warm Tips
Static colours and dynamic modes Adjust the brightness for static colors, the
speed for dynamic modes and the sensitivity for the device mic Thank you in
advance for ordering our products. Before attaching the LED strip lights to
the wall, please plug in the power to test if the lights work well. Hope the
below tips will be useful to you. If you need more help, you can contact the
seller after-sales directly on Amazon by? Orders”—-,. ” Sales—-;.” Contact
Seller”: GD While plugging in the power adapter for the first time, why
Do the lights keep flashing rapidly?
A 1: The lights may be on Mic/Music Mode. This is a very interesting
function. There’s a built-in high-sensitive microphone in the controller to
detect music and surrounding sounds. Lights will change colours and flash
according to the music beats and sounds. Very suitable for parties. If you
need to stop the Mic/Music Mode, please press the “M key on the controller or
select any other modes on the App to stop it.
How could I trim the needless length?
A2: There’s a trimming mark between every eight beads. If you trim, you
must trim by the cutting mark. But the trimmed “needless length” will no
longer work unless it is soldered or connected with a solderless connector.
(The connector does not come with the package,)
Can LED strip lights stick to any surface?
A3: No, please make sure the surface is flat, smooth and clean before
sticking the LED strip light on the surface.
FCC
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation Is Subject to the following two conditions: (1) this device may not cause harmful interference and(2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Warning Statements
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment shall be installed and operated with
a minimum distance of 20cm between the radiator & body.
WARNING
DO NOT IMMERSE IN FIRE CHILDREN UNDER THE AGE OF 16 SHOULD USE THIS PRODUCT
UNDER ADULT SUPERVISION. If you have any questions, please contact our
customer service, and we will reply to you within 24 hours.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>