Beiooya BY001 Espresso Machine 20 Bar User Guide

INSTRUCTION MANUAL

BY001 Espresso Machine 20 Bar

www.beiooya.com
BY001

If there i transportation damage, missing parts, will not be installed and used, contact our emall or scan the code to contact the official. No need to return the product, we send you a beautiful gift for free.
Please read this Instruction Manual and the safety instructions before operating the appliance!
Congratulation on your purchase!
‘This coffee Capsule machine is manufactured with the greatest care. If you look it after properly it will reward you with many years of good service. Before using your new machine, please read this operating manual carefully, paying particular attention to the safety precautions.

Safety Precautions

Please take time to read these safety precautions carefully before connecting your machine to the power supply. It is essential to follow them and the operating instructions.

• First read this entire operating manual.
• Danger of electric shock! Never immerse the machine in water or any other liquid.
• Connect only to a properly grounded power point.
• To make sure that the machine is switched off, remove the plug from the power point.
•  Always pull out the power plug before:
• Relocating the machine.
• Cleaning or maintenance.
• Long periods of disuse.
  • Never clamp or run the power cable over sharp corners or edges.
  • Danger of electric shock! Damaged power cables may only be replaced at the customer service centre.
  • Danger of electric shock! Never touch the power plug/socket/cable or the machine with damp or wet hands. Never unplug by pulling out the power cable; always remove the plug.
  • If you need an extension cable, make sure it is suitable for your machine (3-pole grounded, 1.5 mm2 conductor cross-section), and lay the cable to avoid tripping.
  • Danger of scalding! Never move the machine during operation!
  • Never operate the machine without water
  • Always make sure there is water in water tank not less than minimum level.
  • Danger of burning! Never touch very hot parts of the machine (e.g. brew unit during operations)
  • Danger of scalding! Do not touch the steam or water jets.
  • Danger of scalding! Do not move the operating lever when the machine s still under pressure making Coffee
  • Do not use the machine in case of:
    Faulty operation.
    Damaged power cable.
    After falling or other damage.
    In such cases immediately have the machine checked and repaired if necessary at the customer service centre.
  • The machine location must meet the following requirements:
• Choose a dry, stable and level support surface not immediately underneath the power point. At least 60 cm away from the washbasin and taps.
  *Never place on flammable/fusible surfaces or equipment.
• Never place the machine or power cable on or nearer than 50 cm to hot surfaces or open flames.
• Never cover the machine during operation.
  • Keep children away from the machine during operation.
  • Only use the machine in dry rooms
  • Danger of tripping! Do not let the power cable hang down.
  • This machine is only intended for household use.
  • Pull out the power plug and allow the machine to cool down completely before cleaning and or Maintenance.
  • To prevent damage, never use replacement parts or accessories not recommended by the manufacturer

This appliance can be used by children aged from 8 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and f they understand the hazards involved. Cleaning and user maintenance shall not be made by children unless they are older than 8 and supervised. Keep the appliance and its cord out of reach of children aged less than 8 years.
Appliances can be used by persons with reduced physical, sensory or mental capabi ies or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do ot play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent o similarly qualified persons in order to avoid a hazard.
This appliance is for household and indoor use only.
The appliance must not be immersed
Caution! There is potential injury from misuse.
Heating element surface is subject to residual heat after use.
Coffee-maker shall not be placed in a cabinet when in use cleaning and user maintenance shall not be made by children without supervisior.
This appliance is intended to be used in household and similar applications such as:

• Staff kitchen areas in shops, offices and other working environments;
• Farm houses;
• By clients in hotels, motels and other residential type environments;
• Bed and breakfast type environments.

Notes On This Operating Manual

‘This operating manual cannot cover all possible circumstances. For further information or in case of problems not adequately covered in this operating manual, please contact the service and sales centre.
Please keep this operating manual safe and pass it on to the next user.

Unpacking

• Remove your espresso Capsule coffee machine from its packaging.
• After unpacking, please check that the following parts are included:
  1. Water tank
  2. Coffee machine
  3. Manual

Note:

• Check that your home power supply voltage is the same as marked on the machine rating plate
• Destroy all the plastic bags to prevent danger to children!

Tip: Keep the packaging for transporting the machine (e.g. for removals, servicing, etc.)
Note: You may find a lttle water remaining in the machine.

Component Description

Component description

A| Drip tray
B| Steam pipe
c| Water tank
D| Button
E| Water tank cover
F| Warming plate
G| Rotary Switch
H| Pressure gauge
I| Brewing handle

Function Description

Function description

Switch button| Button button
|
| Switch button| Control machine switch function| Coffee| Coffee function gear| Turn here when making coffee
| Single cup function key| Press the single cup key, the light flickers slowly, the machine starts brewing coffee, and the machine stops automatically after brewing| Steam| Steam function gear| Turn here when making steam
Hot water indicator| The lamp flashes quickly when making hot water| Hot water| Hot water function gear|  Turn here when making hot water
| Double cup function key| Press the double cup button, the light flickers slowly, the machine starts brewing coffee, and the machine stops automatically after brewing| | |
Steam indicator| The lamp flashes rapidly when steam is made| | |

Preparation Before Startup

The twist key must be turned to this position before starting the machine Coffee

https://www.beiooya.com/pages/contact

If there is transportation damage, missing parts, will not be installed and used, contact our email or scan the code to contact the official. No need to return the product, we send you a beautiful gift for free.

Usage Method

The machine must be washed if it s used for the first time or not used for a long time At least 100 ml hot water should be washed with steam pipe, and then one cup of hot water should be washed in the handle.
brewing cup. The specific washing methods are as follows:

1. Make sure the twist key i turned to ‘this position Coffee

2. Transfer to the handle brewing wp

3. Lift the water tank cover

4. Add no more than 1.1 liter of purified water to the water tank (water temperature not higher later samp than 35 °C)

5. Plugin the corresponding power supply

6. 1. Press the switch function key
   2. Each function indicator flashes and the machine is warmed up,
   3. Allindications light up after preheating

7. Steam pipe flushing
   1. Place the cup under the steam pipe (capacity above 100ml)
   2. Turn key from ; Transposition ‘The steam pipe starts making hot water until it is 100 ml.
   Note: Make hot water continuously for 120 seconds. If the rotary knob does not turn back to the coffee position, it will automatically stop making hot water. Itis necessary to turn the turning back to the coffee jon and then turn to the hot water

8. Handle brewing cup washing
   1. Place a cup (more than 100ml) above the waste water tray
   2. Press the single or double cup button and wait for the equipment to finish flushing,(make sure there is more than 150 ml of purified water in the tank)
   3. Precautions: before pressing the key, ‘make sure that the handle brewing cup has been turned into the machine

Brewed Coffee

1. Make sure the twist key is turned to this position Coffee
2. Add coffee powder to the handle brewed cup with a coffee spoon
3. Press the coffee powder with a coffee spoon
4. Transfer to the handle brewing cup
5. Brewed coffee
   1. Put the cup above the waste water pan (make sure there is more than 150 ml pure water in the water tank)
   2. Press the required amount of coffee button (single or double) until the brewing is finished. (make sure there is more than 150 ml of purified water in the tank)
   Tip: when the button is pressed, the button light will flash for a few seconds before brewing. The flash process is in the state of machine heating, which is normal.

Milk Bubble Making

1. Pour no less than 50ml pure milk into the cup
2. Put the milk cup into the steam pipe, making sure the steam pipe is immersed in the milk
3. Turn key from Coffee Bit to , At this time, the steam icator lamp flashes rapidly, and the machine enters the steam mode. At the beginning, there will be a certain time waiting for the machine to heat up. This is a normal phenomenon. After heating, steam will automatically eject foaming milk
4. After finishing Xinyi milk bubble, Turn key from turn back Coffes , Complete milk bubble making (make sure there is more than 150 ml of purified water in the tank)
   Note: after 120 seconds of continuous steam blowing, if the rotary knob does not return to the coffee position, it will automatically stop steam blowing. It is necessary to turn the rotor back to the coffee position, and then turn to the steam position to start steam again

Reminder:
Since the machine has just finished making milk bubbles, the heating body inside the machine is in a high temperature state To ensure the coffee effect and taste, please do not start the coffee mode immediately to brew coffee
Treatment:
It can be made by hot water once When the heating body of the machine is cooled down, a certain amount of steam will be ejected from the steam pipe orifice at the beginning. When the temperature of the heating body decreases, the steam will disappear, and only hot water will be ejected. At this time, the hot water function will be turned off and coffee can be brewed

Hot Water Production

1. Put the cup into the steam pipe
2. Turn key from Bit to At Water, At this time, the hot water indicator flashes rapidly, and the machine enters the hot water mode and starts to make hot water
3. After the completion of Xinyi hot water, Turn key from Water turn back , Complete hot water production. (make sure there is more than 150 m of purified water in the tank)
   Note: make hot water continuously for 120 seconds. If the rotary knob does not turn back to the coffee position, it will automatically stop making hot water. It is necessary to turn the turning back to the coffee position, and then turn to the hot water position to start the hot water again

Energy Saving Mode

Energy saving mode

1. The machine comes with energy saving mode The machine will turn off automatically after 15 minutes, and all function indicators wil be displayed
2. When the machine is off, press the on key again and restart the machine again

Energy saving mode setting
At the same time, press and hold the single cup and double cup buttons, plug in the power supply, and the on-off key lights up

• Press the single cup key, the single cup key light will go out. The energy saving mode will be cancelled
• Press the single cup key, the single cup key light will be on. The energy saving mode is enabled

Descaling Mode

Descaling mode function

1.  place a cup at the water outlet i front of the machine
2. Put a proper amount of scale remover into the water tank
3. Press and hold the single cup button at the same time and plugin the power supply
4. When the on key and single cup key lights are on, press the single cup key to start the descaling function, and the start working time is 1205, Press the small cup key to stop matters needing attention

When the machine makes no more than 400 cups of coffee, it is necessary to regularly remove the scale according to the above functions

Coffee Ration Setting

Single cup time function setting

1. place a cup at the water outlet in front of the machine
2. In standby mode, press and hold the single cup key and the machine starts to work. The machine starts to brew coffee. When itis out to Xinyi brewing time, release the button. Single cup time setting completed minimum 10s, maximum 90s)

Double cup time function setting

1. place a cup at the water outlet in front of the machine
2. In the standby mode, press and hold the double cup button and the machine starts to work. The machine starts to brew coffee. When it s out to Xinyi brewing time, release the button. Double cup time setting completed (minimum 10s, maximum 90s)

Restore Factory Settings

Restore settings

• Press and hold the double cup button, plug in the power supply, and the power on indicator will flash twice to restore the factory settings

Treatment Method of Machine Without Water

Question 1
In the process of making coffee, due to the lack of water in the water tank and adding water again, there is air entering into the internal water path, resulting in no water coming out of the coffee making process.
Processing Method

1. Shut down the machine first and make sure that the power is not pulled out
2. Turn the twist key to Water, Make sure there is more than 150 ml of pure water in the tank
3. Put down a cup with a capacity of more than 100ml under the steam pipe. Press and hold the switch key when the machine is off, and the steam pipe will have clear water until there is water in the cup.

Question 2
When the new machine is used for the first time, or it is not used for a long time, the internal drying of the water pump causes the machine not to discharge water.
Solution: the machine accessories in the “manual air pump” to the machine water.
Processing Method

1. Turn the twistkey to
2. Insert the air pump into the water inlet hole of the water tank, and then add appropriate amount of water
3. Pump waternto the machine with an ai bar

Clean

Matters needing attention:

1. do not immerse the coffee machine in water.
2. Before cleaning the machine, make sure to unplug the power cord
3. Do not use strong detergent, sharp objects, brushes and other objects to clean the coffee machine

Machine cleaning

Handle brewing cup cleaning

Steam pipe cleaning
When the steam pipe water and steam significantly reduced, please install the next step to clean in time

1. Take out the steam pipe sleeve
2. Clean the steam pipe with a cleaning needle

Matters needing attention
Do not pour water directly on the machine

Matters needing attention
When the machine has made no more than 400 cups of coffee, the descaling mode function should be used for regular descaling
**** Pay attention to high temperature
The steam pipe has high temperature and waste heat when making hot water and milk bubble

Common Problem

plugged in properly
2. The switch key is not pressed,
3. Make sure that the power supply is plugged in properly and the power supply is matched correctly. If this phenomenon still occurs, please ask professional personnel for maintenance
No coffee or dripping too slowly| 1. There is no water in the water tank
2. The coffee powder in the handle brewing cup is squeezed too tightly, and the coffee powder is too small or too much| 1. Add water to the water tank
2. Choose the right coffee powder and put it into the brewing cup with middle handle
Water leakage or seepage| 1. Water tank leaks
2. The handle brewing cup is leaking| 1. Check whether the water tank is installed in place or damaged
2. The coffee powder in the handle brewing cup is not pressed wel
The machine can’t work normally, all the indications are on, but not on when pressed| The power supply is not connected| Check whether the power socket is plugged in properly. If it doesn’t work, please ask a professional for maintenance

Product Safety Index

https://www.beiooya.com/pages/contact

If there is transportation damage, missing parts, will not be installed and used, contact our email or scan the code to contact the official. No need to return the product, we send you a beautiful gift for free.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>