Aduro 22 Series Round Wood Burning Stove Slender Design User Manual

: June 15, 2024
: ADURO

Table of Contents

Aduro 22 Series Round Wood Burning Stove Slender Design
Product Information
Product Usage Instructions
General
- Technical data
Installation of the stove
Lighting the stove
- How to operate Aduro-tronic
The chimney
Maintenance and cleaning of the stove
Accessories
Right of complaint
Aduro 22.4 Lux wall mounting
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aduro 22 Series Round Wood Burning Stove Slender Design

Product Information

Aduro 22 Series

Specifications

Model: Aduro 22, Aduro 22.1 Lux, Aduro 22.3 Lux, Aduro 22.4 Lux, Aduro 22.5 Lux
Latest Revision: 17.10.2023

General

Approvals
Home Transportation
Technical Data

| Top/Back| Dimensions (cm)| Weight (kg)
---|---|---|---
Aduro 22| 98.2 x 44 x 40.3| 80
Aduro 22.1 Lux| 113 x 44 x 40.3| 101.3
Aduro 22.3 Lux| 106.1 x 44 x 40.3| 94.4
Aduro 22.4 Lux| 75.7 x 44 x 41.3| –
Aduro 22.5 Lux| 113 x 44 x 40.3| 101.3

Product Usage Instructions

Placement/Distance Requirements

Next to the stove (A): 70cm
Behind the stove (B): 7.5cm
Above the stove: 50cm

Connection to Masonry Chimney

External Combustion Air Supply

Installation Options
Via Wall
Via Floor and Foundation

Important Safety Information

Aduro-tronic

Chimney

Data

FAQ (Frequently Asked Questions)

How do I remove the construction spring? (only for single occupancy)
Can I use the stove without external air supply?
How should I not install the stove?

Aduro 22 series Aduro 22, Aduro 22.1 Lux, Aduro 22.3 Lux, Aduro 22.4 Lux & Aduro 22.5 Lux
EN13240 – Ecodesign 2022
aduro.dk/adurofire.com

Congratulations on your new Aduro stove!
To get the best possible experience and benefit from your new Aduro wood burning stove, it is important that you read the user manual thoroughly before you install the stove and start using it. Errors or incorrect settings can cause hazardous conditions and/or poor operation.
For further information, please go to www.adurofire.com.

Extended product warranty – free online registry
You have the opportunity to extend the warranty on your wood burning stove from the statutory right of complaint to an extended warranty of five years. All you need to do is register the stove at www.adurofire.com/warranty/. The deadline for registering is five months from the date of purchase.

Production number
The wood stove has a production number on the rating plate on the back of the stove. For most of our stoves, the production number is also stamped on the front page of the quick guide that is enclosed with the stove. For the purposes of the guarantee and for other enquiries, it is important that you are able to quote this number.

HOW TO SUCCEED WITH YOUR NEW WOOD BURNING STOVE
In Aduro’s Customer Service Center you will find tips and tricks on how to succeed with your new Aduro wood burning stove. Here you will have direct access to interesting content about maintenance of your stove as well as support related information.

General

Compliance
The wood burning stove complies with the European Directive Ecodesign 2022, the EN13240 European standard as well as the NS3058 Norwegian standard and is thereby approved for installation and use in Europe. At the same time, the manufacturing process is subject to external quality control. DoC (Declaration of Conformity) can be downloaded at www.adurofire.com/download/.

Transportation
When taking your wood burning stove home, please ensure that it travels in an upright position. If you wish to lay it flat, it is important that you remove all loose parts from the combustion chamber (cast iron grate, baffle plates, and insulation tiles) and remove the ashpan. Otherwise, you can leave the insulation tiles and the cast iron grate in the combustion chamber and then fill it up with surplus packaging to secure the loose parts.

Technical data

Dimensions in cm:| Aduro 22| Aduro 22.1 Lux| Aduro 22.3 Lux| Aduro 22.4 Lux| Aduro 22.5 Lux
---|---|---|---|---|---
Flue outlet, diameter| Ø15

top/rear

| Ø15

top/rear

| Ø15

top/rear

| Ø15

top/rear

| Ø15

top/rear

Outer dimensions

(HxWxD)

| 98.2 x 44

x 40.3

| 113 x 44

x 40.3

| 106.1 x 44

x 40.3

| 75.7 x 44

x 41.3

| 113 x 44

x 40.3

Height exhaust branch

above floor*

| 96.1| 111| 104.1| –| 111
Distance from floor to centre of rear outlet*| 86.5| 101.3| 94.4| Min. 65.1

+ 22.5**

| 101.3
Distance from centre of exhaust branch to rear edge of stove*| ****

18.5

| ****

18.5

| ****

18.5

| ****

19.3

| ****

18.5

– Optimum insulation

– Average insulation

– Inadequate insulation

| ****

150 m2

100 m2

60 m2

Installation of the stove

You may install your wood burning stove yourself – but we strongly recommend that you consult your chimney sweep before beginning the installation. It is important to ensure that all local rules and regulations, including ones relating to national and European standards, are complied with when installing this device. Your dealer can also provide you with installation advice. Remember, it is your responsibility that rules in force are complied with.

APPLIES TO UK INSTALLATION ONLY: To comply with UK building regulations an approved CO monitor should be installed in the same room as the appliance.

You may not begin to use the stove until it has been inspected and approved by your local chimney sweep.

Position of the stove/distance requirements

Distance requirements will only apply if the wood burning stove is to be placed close to flammable materials:

Distance to flammable

material (cm)

| To the sides

(A)

| Behind the stove

(B)

| Distance to furniture

(C)

| Corner position

(D)

| Above the

stove

---|---|---|---|---|---
Aduro 22| 70| 7.5| 100| –| 50
Aduro 22.1 Lux| 40| 7.5| 100| 10| 50
Aduro 22.3 Lux| 70| 7.5| 100| –| 50
Aduro 22.4 Lux| 70| 7.5| 100| –| 50
Aduro 22.5 Lux| 70| 7.5| 100| –| 50

$Aduro-22-Series-Round-Wood-Burning-Stove-Slender-Design-FIG- $1$$

If the stove is positioned against a brick wall or other non-flammable material, there are no minimum distance requirements. To facilitate cleaning and for the best use of the convection air, we recommend that you keep a distance of approximately 5-10 cm to the wall.
If the wood burning stove is to be placed on a flammable material such as a wooden floor or carpet, it must be placed on a non-flammable floor hearth. The floor hearth should extend for at least 30 cm in front of the stove and 15 cm on each side measured from the opening of the combustion chamber.

The wood burning stove must be installed on a floor with the adequate load bearing capacity. If the existing construction does not meet this requirement,
appropriate adaptation measures must be taken (e.g. a load distributing plate).

Pipe connection
Please ensure that all local rules and regulations are complied with, including CE marking of the flue pipe. Additionally, distance requirements to flammable material for the pipe must be respected.
A flue pipe with an internal diameter of 150 mm should be used for all Aduro stoves.
The stove leaves the factory with the flue outlet mounted on the top. If you require the flue outlet on the back, break off the cover plates positioned at the top of the back of the stove. Exchange the exhaust connector (from the top outlet) with the cover plate from the rear outlet. Mount the cover plate from the rear outlet to the top outlet. The top outlet is finished with the plate that lies in the ashpan. You may benefit from putting a slim gasket between the flue on the stove and the flue pipe.

Connection to a brick chimney

If the stove is being connected to a brick chimney you should use the rear outlet or a curved flue pipe via the top outlet. After measuring, a hole is made in the chimney in which the pipe sleeve is placed, and stove mortar is used to seal it in place. The stove is placed in position, and the flue pipe is put in place. A thin gasket is placed between the flue pipe and the pipe sleeve to seal the joints. The flue pipe should protrude into the pipe sleeve but must not block the opening in the chimney (see the illustration below). You may benefit from putting a slim gasket between the flue on the stove and the flue pipe.

The stove can be connected to a chimney to which other heat sources are connected.

Applies to Aduro 22.4 Lux:
Aduro 22.4 Lux must be mounted onto brick chimneys including insulated chimney elements. The stove cannot be mounted directly to a brick chimney without insulated chimney elements or directly onto insulated chimney elements as shown below:

$Aduro-22-Series-Round-Wood-Burning-Stove-Slender-Design-FIG- $3$$

Attachment / hanging of Aduro 22.4 Lux
Aduro 22.4 Lux must be installed on a non-flammable wall. The stove is being delivered with a wall bracket which must be properly fastened to the wall before mounting the stove (find instructions for mounting the bracket at the back of this user manual). You may consult your normal supplier of building materials about suitable attachment materials for the stove/wall before the mounting. ONLY USE FIXING MATERIALS WHICH CANNOT MELT. If you have any doubts about the requirements, please consult your chimney sweep who will inspect the stove.
When the wall bracket is mounted and fastened correctly, the stove can be pushed into place. The stove can now be fastened to the wall bracket with a safety bracket on top of the stove (see picture 1) and a safety plate under the bottom (see picture 2).

The lower edge of the stove must be minimum 22.5 cm above the floor.

Supply of combustion air
All wood burning stoves need constant supply of air to ensure a clean and efficient combustion. This is often a problem in modern, energy-efficient houses that are very tight. Therefore, the wood burning stove is equipped with external supply of combustion air, where the air to the combustion can be provided through a channel from the outside and directly into the wood burning stove. The amount of air needed for combustion is 25 m3/h. Air vents must be positioned where they cannot be blocked.

The connecting pipe for the external air supply has an external diameter of 78 mm, to which you need a pipe with a diameter of 80 mm. If the pipe work is more than 100 cm, or if there are bends on the tube, the resistance in the pipe increases significantly. Negative pressure outside on the sheltered side of the house can also affect the resistance of the pipe. In these situations, the pipe should have a diameter of minimum 100 mm. It may also require a stronger chimney draft, which you can achieve by installing an Aduro DraftOptimizer.
You can easily test the resistance in the pipe by opening a window close to the stove, disconnect the external air supply and then light up the stove. If the combustion looks different than before, there is too much resistance in the external air supply. If the pipe work is longer than 1 m, the pipe diameter must be increased to 100 mm and a correspondingly larger wall valve must be chosen. In warm rooms, the channel should be insulated with 30 mm mineral wool covered with a damp-proof course (plastic). It is important that the lead-in between the pipe and the wall (or floor) is sealed with jointing compound. If necessary, you can use the complete Aduro Fresh Air Kit.

The pipe with external supply of combustion air can be taken out at the bottom of the back side of the stove or under the stove (see illustration below):

$Aduro-22-Series-Round-Wood-Burning-Stove-Slender-Design-FIG- $5$$

Using the stove without external air supply
If you want to use the wood burning stove without connecting the supply of combustion air, break off the cover plate in the rear cover at the bottom of the back of the stove. Otherwise, there is not enough air for the combustion.
In very well-insulated houses, or houses with powerful cooker hoods and/or air conditioning systems, a vacuum can be created around the wood burning stove, leading to smoke leakage and poor combustion. In these circumstances, it might be necessary to open a window to provide air for the combustion and to equalize the vacuum. Alternatively, you could place an air vent in the room where the wood burning stove is placed.

Installation options

$Aduro-22-Series-Round-Wood-Burning-Stove-Slender-Design-FIG- $6$$

Do not install the stove in the following ways:

$Aduro-22-Series-Round-Wood-Burning-Stove-Slender-Design-FIG- $7$$

Through a damp crawl space:
If the air is drawn from a damp crawl space, you won’t achieve an optimum air intake.

With air intake upwards:
If the air intake is turned upwards,there will be too much resistance for the air intake.

Lighting the stove

Important safety information:

The wood burning stove will become warm during use, and therefore it should be treated with all necessary caution.
Never keep easily combustible fluids such as petrol in the vicinity of the wood burning stove.
Never use easily combustible fluids to light the fire in the wood burning stove.
When lighting a fire and adding new wood logs, it is important to get the fire burning fast. If the fire does not start quickly and wood only smoulders, it can cause strong smoke formation and in worst case cause an explosive ignition of the flue gasses, which can damage the stove.
Never empty the ashpan when the wood burning stove is warm. Embers may still be found in the ashpan for up to 24 hours after the fire has gone out. Please wait to empty the ashpan until you are sure that there are no embers in the ash.
The door should be kept closed while the wood burning stove is in use. While lighting the fire, the door can stand ajar for the first few minutes.
When putting logs in a hot stove, you must always open the primary air intake and make sure that the wood ignites within 2-3 minutes. If the wood does not ignite, add some ignition products, and ignite them manually. Please make sure that the flames are burning steadily for the first 10 minutes before you leave the stove.
In the event of a chimney fire: Close all the dampers on the wood burning stove and call the fire-fighting service.

Air damper
The stove is equipped with an air damper for regulation of the primary and secondary air supply. The primary air is used at the beginning to get the fire going, and the secondary air keeps the fire burning evenly. The tertiary air ensures that flue gasses are burned and is not adjustable. You must always add secondary and tertiary air, while firing the stove. The air-wash system that minimises soot on the front glass is also adjusted by this damper.

The damper allows you to adjust the stove according to the chimney draft and the heat output you require. The longer the damper is pulled out, the more air is added, and the more powerful the combustion. The illustration below shows the stove with the damper indicated. Use the edge of the door to read the position of the inlet air:

Fully open primary, secondary, and tertiary air inlet. This position can be maintained with the Aduro key, which must be placed in the two holes. See section 3.2.1.
Closed primary air inlet, fully open secondary and tertiary air inlet.
Closed primary air inlet, half way closed secondary air inlet and fully open tertiary air inlet.
Closed primary and secondary air inlet, fully open tertiary air inlet.
Regulator p ushed all the way in. All air inlets are closed.

Primary air
When you add new logs, the primary air should be opened until the fire is burning properly. In order to utilise the fuel to the fullest extent, the embers should have burnt for so long that it is necessary to open the primary air for approx. 2 minutes to get the logs burning. However, it is important to fire at a certain time so that the flames do not go out during the closing time for the Aduro-tronic.
In order to reduce the risk of ash falling from the stove when the door is opened to add more fuel, it is a good idea to open the primary air for approx. 1 minute before the door is opened. This increases the draft through the stove.

Secondary air
In normal circumstances, the wood burning stove should be working with the secondary air open between 60 % and 100 % (the damper is placed between position 2 and 3. See section 3.1). You should never close the air intake so far that the flames go out. There should always be visible flames in order to achieve a clean and efficient combustion. A too low supply of air can lead to bad combustion, high emissions, and a low efficiency. If you want to fire in the stove with the lowest possible effect – around 3 kW – you must close the secondary air almost completely approx. 45 minutes after stoking. At this point there are only few flames, and the stove can burn clean by using the tertiary air from the back of the combustion chamber.

Aduro-tronic
Aduro wood burning stoves are equipped with the patented Aduro-tronic automatic as a standard. Aduro-tronic is a manually operated mechanical start- up device, which works without the use of electricity. It automatically regulates the combustion air and thus secures an efficient combustion. For further information, go to www.adurofire.com.

How to operate Aduro-tronic

When lighting
When lighting a fire in the stove, the maximum amount of primary air will be needed to light the fire. For that reason, the damper can be kept “forcibly open”. This is done by pulling the damper forward as far as possible and then fixing it with the Aduro Key (see illustration). When the stove is warm and a layer of embers has been created on the bottom of the combustion chamber, the Aduro-tronic can be set to the automatic position, i.e., the Aduro Key can be removed. Alternatively, you can leave the door ajar the first few minutes during the ignition phase (without the key).

When stoking
You activate the automatic by pulling out the damper every time new firewood is added. The Aduro-tronic automatic will then close the damper gradually after the pre-programmed time.

Regulation of the Aduro-tronic automatic
The automatic is pre-set to close the primary air intake within 6 minutes. This setting has been used during testing at the Danish Technological Institute using a standard chimney and ‘standard’ sized logs (approx. 24 cm long and 10×10 cm thick) with maximum moisture content of 18%. In practice, such circumstances can differ, which is why the Aduro-tronic automatic can be adjusted to your circumstances. If you want a slower intake of primary air (e.g., for a lower chimney draft, larger sized wood, or for longer intervals between stoking), adjust the screw on the front of the control bracket using a small allen key. If the screw is turned to the right, the closing time is increased, and if turned to the left, the closing time is reduced.

How should I use my wood burning stove?

The wood burning stove is intended for intermittent combustion. This means that each stoking should burn down to embers before new logs are added. Always respect the MAX-load line which marks the limit for the amount of wood.
You can regulate the effect/heat output with the fuel. Burning small logs provides more powerful combustion than burning large logs. The ideal heat output is reached by burning approx. 1.8 kg wood per hour. The nominal output is achieved by firing with 2 pieces of birch wood of approx. 24 cm, with the secondary air reduced to approx. 85%, and with an ignition interval of 45 minutes.
If you experience problems lighting the fire or the fire dies after a short time, it can be due to the following reasons:

The firewood is not dry enough. The firewood should have a moisture content of max. 18%.
There is a negative pressure in the house. See section 2.5.
The smoke outlet from the outside may be blocked from sooth. This can occur after chimney sweeping. Control the smoke outlet.
The used amount of wood may have been too small. This results in a too little and too cold layer of embers which cannot light the new wood.

If you overload the wood burning stove and burn more than the recommended amount of wood per hour (see sect ion 1.3), there is a risk that the surface of the stove will become discoloured and eventually fall off. The stove can be resurfaced.

The first time a fire is lit
The wood burning stove is packed in recycling packaging. The wood from the packaging can be sawed into smaller pieces and used the first few times a fire is lit. The plastic packaging must be disposed according to national rules regarding disposal of waste.
During transportation, it may happen that the baffle plate in steel falls out of place. Therefore, before using the stove, please make sure that the baffle plate is properly placed (on the hooks or fastened to the bolts depending on the model) for optimum combustion and for preventing soot on the glass.
The first few times the wood burning stove is used, there may be some smoke and unpleasant odours from the wood burning stove, which is normal. This is caused by the heat-resistant paint hardening. Make sure there is sufficient ventilation during this stage. It is also important not to let the fire burn too fiercely the first 2-3 times, so that the steel has time to expand slowly.
You should also be aware that the stove may make some clicking sounds as it heats up and cools down – like pouring boiling water into a sink. These are caused by the great differences in temperature to which the materials are being exposed.

During the first firing, which should be carried out using approximately 1 kg of wood, the door must be left slightly open and must not be closed until the stove is cold. This is to prevent the gaskets from sticking to the stove.

Lighting a fire in the wood burning stove
The fire lighting method is very important for starting combustion quickly and efficiently.

Pull the damper under the door out to open primary, secondary, and tertiary air supply.
Place a log of wood crosswise in the combustion chamber and put 2 firelighters close to the log. Light the firelighters and quickly put a new log close to the firelighters and several small logs at an angle above it. Air must be able to reach the firelighters, but the logs should be touching to “warm” each other.
When there are distinct, visible flames and the fire is burning well, close the primary air (see section 3.1)

The control handles will get warm when the wood burning stove is in use.
Please use the glove provided when you operate the wood burning stove.

Recommended fuels
We recommend the use of split hardwood that has been stored outdoors under cover for at least 1 year. Wood that has been stored indoors has a tendency to become too dry and will burn too quickly. We recommend that you fell the wood during the winter when a lot of the moisture in the wood will have been drawn down into the roots. In order to achieve optimum combustion, the wood’s moisture level should not exceed 18%, which roughly corresponds to storing the wood outdoors under a cover for one year. The moisture level of the wood can be measured using a wood moisture meter or by applying dishwashing liquid to one end of the log and blowing air in the other end. If the wood is dry enough, soap bubbles will appear. The wood should be chopped into logs with a diameter of approx. 10 cm and a length of max. 35 cm. Firing with wet fuel will reduce the energy efficiency and increase the particle emission.

Burning varnished wood, impregnated wood, chipboard, paper, and other waste is strictly forbidden. Burning these materials will damage the environment, the wood burning stove, and your own health. Fossil fuels must not be used.

The chimney

The stove is tested in accordance with current standards, where a smoke exhauster secures a constant chimney draft of 10-14 Pascal (Pa). However, with a natural draft (without a smoke exhauster installed) the chimney draft will increase to 18-25 Pa at optimum conditions. There are many factors that affect the chimney draft, including the outside temperature, wind strength, and surrounding buildings. There are no requirements with respect to specific chimney heights, but a chimney must be tall enough to provide a good draft. If the recommended chimney draft is not achieved, there may occur problems with smoke coming out of the door during firing.

Calculation of chimney when firing with wood

Data| Aduro 22 series
Flue temperature at [20°C]| 286
Chimney draft at testing power [mbar]/[Pa]| 0.12 / 12
Flue gas mass flow [g/s]| 5.5

Inadequate draft in the chimney
If you experience poor draft in the stove after the installation, please make sure that there is nothing in the chimney to restrict the smoke and that no nearby buildings or trees affect the winds around the chimney.
If the chimney is too short, leaks, or is inadequately insulated, there may be problems with the chimney draft (let the chimney sweep assess this). The draft should be sufficient during the ignition phase when the stove/chimney is cold to provide a clean combustion and prevent smoke leakage. Therefore, we recommend a chimney draft around 5 Pa in the ignition phase.
Once the ignition is a success, and the smoke temperature is rising, it is important that the chimney draft reaches a stable area around 18-25 Pa in operation (1 hour after ignition) when the chimney/stove is hot. The draft in the area of 18-25 Pa when the stove is hot is essential in order to achieve an optimum and clean combustion. Therefore, we recommend that you measure the chimney draft when the chimney is cold and when it is hot after 1 hour in operation.
In practice, the chimney draft will differ – especially in cold condition. Therefore, the best indication of the chimney draft is to measure the draft when it is hot. If the chimney sweep judges the draft to be sufficient, but you still have problems lighting a fire, try extending the ignition phase by using more thin pieces of kindling and 1-2 firelighters, so that the chimney gets thoroughly warm. The chimney will not draw at optimum effect until it is warm. When a layer of embers has been formed, add 2-3 dry logs.
If it is impossible to establish a sufficient natural chimney draft, you can mount a smoke exhauster, e.g. Aduro DraftOptimizer.

Chimney and smoke
If you experience smoke coming out of the stove or the start section of the smoke pipe, it could be due to certain weather conditions. On stormy or cold winter days, or if the chimney has not been used in a while, a cold plug can be created in the chimney, meaning the natural draft will be at its minimum.

If the chimney is cold and cold plugs are created, you may experience smoke leaks during the ignition phase. In this situation there can be more smoke than usually in the combustion chamber, and some of it might leak out of the stove. Therefore, if you have a cold chimney that has not been used for a while, we recommend that you use some wood sticks to heat the chimney and eliminate the cold plug.

Maintenance and cleaning of the stove

All maintenance and cleaning of the stove should be carried out when the stove is cold.

Combustion chamber
The fireproof tiles in the combustion chamber eventually wear out and should be replaced when the cracks are more than 0.5 cm wide. The durability of the tiles depends on how often and how intensively the stove is used. You can change the tiles yourself. They are available as a ready-to-use set. You can buy the sets at www.aduroshop.com.

Glass
Wet wood, unsatisfactory chimney draft, and wrong use of the stove can leave soot stains on the glass panes. It can easily be removed using a damp cloth that you dip in cold ash and rub on the sooty glass. Special cleaning agents are also available to remove soot from glass, e.g. the Aduro Easy Clean pad. The pad neither scratches nor damages the glass and is for multiple usage. Water or other cleaning agents are not necessary.
It is common maintenance to tighten the glass fittings and the hinges shortly after the stove has been installed.

Gaskets
Check if the gaskets around glass and door are properly placed. Over time, the gaskets will wear out and should therefore be checked regularly. If leakages appear, they should be replaced, as it is essential that the stove is tight.

Adjusting the door
Adjusting the door and the closing mechanism is a necessary part of the maintenance of the stove, which you can easily do yourself. If the door hangs on one side, feels sluggish to close or does not close properly, you should adjust and tighten the hinges and fittings around the door.

Ashes
Empty the ashpan before it gets completely full but always leave a layer of ashes in the combustion chamber because it insulates and makes it easier to light a fire next time.

Cleaning the stove
The stove’s surface will stay at its best just by being vacuumed with a small, soft mouthpiece or dusted with a soft, dry cloth. Do not use spirit or other solvents, as they will remove the paint.

Do not clean the stove with water. If the stove is exposed to moisture, the stove may develop rust.

The inside of the stove and the flue pipe can be cleaned through the door or alternatively through the cleaning aperture in the flue pipe/chimney. The upper fireproof tile (the baffle plate) can be removed. To allow free access to the top of the stove and the flue pipe, also remove the baffle plate in steel. The flue pipe can be removed from the stove and cleaned. Cleaning of the inside of the stove and the flue pipe should be undertaken at least once a year, or more frequently if necessary, depending on how often the stove is used. This work can also be carried out by the chimney sweep or your local Aduro GO partner.

Repairing the surface
The stove is painted with a heat resistant paint that can withstand temperatures up to 500 degrees. If the surface of the stove gets scratched or worn, it can easily be renewed using this type of paint. The paint is available in black metallic at www.aduroshop.com/aduro-spray-black-metallic- 53262a.

Spare parts and unauthorized alterations
You may only use original spare parts for your stove. All forms of unauthorized alterations to the stove are strictly forbidden, as the stove will no longer comply with the approved specifications. At www.aduroshop.com you can buy original spare parts for your stove.

Bauart safety spring
All Aduro stoves are fitted with a “Bauart” safety spring. The mechanism ensures that the door of the stove closes automatically. The “Bauart” spring is a law requirement in some European markets, so please check your local regulations if you wish to permanently remove this feature.

If you wish to remove the spring, here is how to do it:

Use a pair of pliers to pry the upper hook of the Bauart spring out of the hole in the stove’s door. Watch this video.
Please note that the spring is in tension when the door opens, so make sure to protect yourself during removal. We recommend that you use protective gloves.
For optimum combustion, we recommend that you close the hole in the stove with a self-tapping screw, sealing compound, or ceramic glue.

Accessories

For Aduro stoves we offer a wide range of accessories to fulfil the experience: Companion sets, firewood baskets, fireplace grid, floor hearths, flue pipes, and kindling products. For further information, go to www.adurofire.com/accessories/.

Right of complaint

The right to complain applies in accordance with the sales act in the country where the stove was purchased. The dated receipt will be sufficient proof.
The right of complaint does not cover:

Damages resulting from incorrect installation and use of the stove, overheating and wrong or missing maintenance of the stove etc.
Consumable service parts (glass, gaskets, insulation tiles, slides, painted surfaces, cast iron grate etc.), which are subject to normal wear and tear. You can buy these parts in our online shop www.aduroshop.com.
Damages caused by electrical surcharge, (condensation) water in and around the chimney, too much or too little draft in the chimney and missing maintenance/cleaning of the chimney/flue pipe/installation.
Damages to the stove caused by external influences or damages caused by the stove on other objects.
Read more at www.adurofire.com/warranty/

Disposal of the wood burning stove

When disposing your wood burning stove, metal, vermiculite, and ceramic glass must be sorted separately.
Dispose hereafter the materials according to the regulations at your nearest recycling depot.

Aduro 22.4 Lux wall mounting

Dismount the top plate . Afterwards, dismount the safety bracket and pull the wall bracket away from the stove.
Dismount the heat shield.
If using the back outlet, please remove the round circle from the heat shield and the wall bracket.
Mount the wallbracket securely in the desired position.
ONLY USE FIXING MATERIALS, WHICH CANNOT MELT.
If using the back outlet, the pipe must go precisely 3 5 mm out of the wall.
IMPORTANT:
mount the heat shield on the wall bracket again.
Place the stove on the lower rails of the bracket and push the stove in place.
Secure the stove by mounting the safety bracket on top of the stove ag ain. You can now remount the top plate.
Mount the safety plate under the stove.
Note: You will find plate and screws for the assembly in the ashpan.