GRAINFATHER 40L Sparge Water Heater Instructions

: June 15, 2024
: GRAINFATHER

Table of Contents

GRAINFATHER 40L Sparge Water Heater
Product Information
Product Usage Instructions
FAQ
SAFETY INFORMATION
DIAGRAM
ASSEMBLY
HOW TO USE
INSTRUCTIONS FOR SAFE USE
CLEANING & STORAGE
TECHNICAL SPECIFICATIONS
FUTURE REFERENCE
Contacts
GET IN TOUCH:
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

GRAINFATHER 40L Sparge Water Heater

GRAINFATHER-40L-Sparge-Water-Heater-product

Product Information

Specifications

Volume: 40L
Voltage: 220V-240V (110V-120V US)
Power: 2300W (1500W US)
Frequency : 50Hz/60Hz
Dead space: 2.5L

Product Usage Instructions

Assembly

Before assembling the Sparge Water Heater 40L, you will need a Phillips screwdriver.

Installing the Lid

Place the handle on the top of the lid.
Take the screw and thread on the stainless-steel washer, then the silicone washer.
Using a Phillips screwdriver, tighten the screw through the hole in the lid and into the threaded hole in the handle.

Assembling the Tap

Remove the stainless-steel nut and rubber gasket from the ball valve tap. From the inside, put the tap’s threaded shank through the bottom hole on the Sparge Water Heater.
Place the silicone washer on the threaded shank on the inside of the Sparge Water Heater.
While holding the tap with one hand to ensure that you keep the tap facing the right direction, install the nut onto the threaded shank.
Tighten the nut to just beyond the finger tight.
Test for leaks by filling the unit with enough water to cover the shank.
If there are leaks, ensure that the silicone washer is flat and centered on the shank.

How to Use

Remove the lid and fill the Sparge Water Heater with tap water. Do not fill past the “max” level indicator on the inside of the unit.
Replace the lid and plug the unit into a power socket.
Press the “on” switch. The heating light will illuminate, and the water will begin to heat.
Use the tap to dispense the water.

How to Use Continued

Always make sure that approximately 3 cups of water remain in the appliance to avoid it overheating.

Note :

This device has a thermal cutoff switch to prevent dry boil. If the element overheats, the thermostat will automatically turn off the machine. If you experience overheating, please wait a few minutes for the appliance to cool down and reset the temperature.

FAQ

What is the dead space of the Sparge Water Heater 40L?

The dead space of the Sparge Water Heater 40L is 2.5L.

Can I use the Sparge Water Heater for commercial and indoor purposes?

Yes, the Sparge Water Heater is suitable for commercial and indoor use only.

How can I contact customer support for further assistance?

You can reach out to our customer support team through the following channels:

Email : info@grainfather.com
NZ +64 6 888 3027
AU +61 2 8074 3798
US +1 562-354-4603
UK/EU +44 1750 432048

Where can I find more information and FAQs about the product?

You can visit our FAQ’s page at https://shop.grainfather.com/index.php/faq.

Is there a mobile app available for the Grainfather?

Yes, you can download the FREE Grainfather App for additional features and functionalities.

THANK YOU FOR CHOOSING THE GRAINFATHER SPARGE WATER HEATER 40L

Get familiar with your equipment by following these quick and easy steps. We recommend reading the following safety information before use. Please also find enclosed, advice for cleaning and storing your Sparge Water Heater 40L.

SAFETY INFORMATION

Read all instructions carefully.
Before use, check the rating label and make sure that the Sparge Water Heater voltage is fit or your outlet voltage.
The earth terminal of the plug should be connected to the earth block of the power supply.
Do not use the Sparge Water Heater if the cord or plug is damaged.
If damaged, please replace it before use.
Switch the of button and the power outlet, beore unplugging.
Do not move the product while in use.
Grasp the plug when you remove it. Do not pull the cord.
Do not let the power cord hang over the edge of a table or counter.
Do not operate the unit without water.
Do not place it near a gas cooker, electric burner, heated oven, or other sources.
Keep the power cord and plug away from the water.
Unplug the power cord from the outlet and let the plug cool before cleaning.
Switch the unit of and unplug the power cord after use.
Do not use this appliance outdoors.
Do not use this product with a power extension cord as an overload may occur.
The appliance is only to be installed in locations where it can be overseen by trained personnel.
Never leave the unit unattended while in operation.

NOTE :

Not following the safety information above may void your warranty.

DIAGRAM

ASSEMBLY

Before assembling this product, you will need a Phillips screwdriver.

INSTALLING THE LID

1. Place the handle on the top of the lid.
2. Take the screw and thread on the stainless-steel washer then the silicone washer.
3. Using a Phillips screwdriver, tighten the screw through the hole in the lid and into the threaded hole in the handle.

ASSEMBLING THE TAP

Remove the stainless-steel nut and rubber gasket fromthe ball valve tap. Fromthe inside, put the taps threaded shank through the bottom hole on the Sparge Water Heater.
Place the silicone washer on the threaded shank on the inside of the SpargeWater Heater.
While holding the tap with one hand to ensure that you keep the tap facing the right direction, install the nut onto the threaded shank.
Tighten the nut to just beyond the finger tight.
Test for leaks by filling the unit with enough water to cover the shank.
If there are leaks, ensure that the silicone washer is flat and centered on the shank.

HOW TO USE

Remove the lid and fill the SpargeWater Heater with tap water. Do not fill past the ‘max’ level indicator on the inside of the unit.
Replace the lid and plug the unit into a power socket.
Press the ‘on’ switch. The heating light will illuminate and the water will begin to heat.
Set the required temperature on the thermostat dial. Once the temperature has been reached, the ‘keep warm’ light will automatically switch on and the water will be kept at the specific temperature until required.
- NOTE: The thermostat has a hysteresis of 5°C (10°F), so it is important to have a thermometer to check the temperature and to make sure that the water is at 75°C (167°F).
Use the tap to dispense the water.
Always make sure that approx. 3 cups of water remain in the appliance to avoid it overheating.
- NOTE: This device has a thermal cut of switch to prevent dry boil. If the element overheats, the thermostat will automatically turn of the machine. If you experience overheating, please wait a few minutes for the appliance to cool down and reset the temperature.

INSTRUCTIONS FOR SAFE USE

Do not remove the lid while boiling.
Position the lid so that steam is directed away fromthe handle.
Do not carry the SpargeWater Heater while it contains liquid.
Do not overall the product as boiling water may over ow. If the power supply cord is damaged, it must be replaced by the manufacturer or its service agent, or a qualified person to avoid a hazard.
This appliance should not be used by children. Keep the product and its cord out of the reach of children.
This product is not intended for use by persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Do not use a high-pressure washer when cleaning. The product should not be immersed in water or liquid

CLEANING & STORAGE

ADVICE FOR CLEANING & STORAGE

Always disconnect the appliance before cleaning.
For the rest clean, rinse with clean water to remove any dust and cardboard debris.
After use, the appliance should be cleaned immediately. If the remnants of wort and andmalt appear on the surfaces, do not let these dry out as this will significantly complicate the cleaning process.
All stainless-steel components can be cleaned using a conventional, unscented detergent. Abrasive agents and sponges/brushes could cause scratching, and are not suitable for use. Ideally, use a dish brush to clean the base of the unit.
Clean the valve and all components.
After cleaning, allow the product to air dry or use a towel.
Do not store in a damp area as this could cause damage to the product.