Namsung Corporation XGPS360S Universal GPS Receiver User Guide

Namsung Corporation XGPS360S Universal GPS Receiver

Specifications

• Project Name: Universal GPS Receiver
• High-sensitivity, dual-band GNSS receiver
• Works with most apps that require GPS
• Supports both NMEA and iOS protocols
• Small and light
• Operating time: ~10 hours (for 1 device)
• Charging time: ~3 hours
• Input voltage: 5 VDC
• Internal Battery Capacity: 1400 mAh

Dimensions

• XGPS360S Body(mm): 55.0 x 70.0 x 22.0
• Non-slip pad (mm): 107.0 x 122.0 x 25.0

GPS/GNSS

• GNSS supported simultaneously
• SBAS (WASS, MSAS, EGNOS, GAGAN)
• GPS: L1 1575.42 MHz
• Cold Start:

Product Usage Instructions

Step 1: Charging the Device

To ensure optimal performance, charge the XGPS360S before using it for the first time.

1. Connect the included charging cable to the input port of the XGPS360S.
2. Plug the other end of the charging cable into a power source with a 5 VDC output.
3. Allow the device to charge for approximately 3 hours or until fully charged. The LED indicator will turn green when the charging process is complete.

Step 2: Pairing with Your Device

The XGPS360S can be used with various apps that require GPS. To use it with your device, follow these steps:

1. Ensure that your device’s Bluetooth is enabled.
2. Turn on the XGPS360S by pressing and holding the power button until the LED indicator lights up.
3. On your device, go to the Bluetooth settings and search for available devices.
4. Select “XGPS360S” from the list of available devices toinitiate the pairing process.
5. Follow the on-screen instructions to complete the pairing process.

Step 3: Using the XGPS360S

Once paired, you can start using the XGPS360S with your apps that require GPS.

Make sure your device is within range of the XGPS360S and has a clear view of the sky for optimal GPS signal reception.

Frequently Asked Questions (FAQ)

Q: How long does the XGPS360S battery last?

A: The XGPS360S has an operating time of approximately 10 hours for one device. However, actual battery life may vary depending on usage and other factors.

Q: Can the XGPS360S be used with iOS devices?

A: Yes, the XGPS360S supports both NMEA and iOS protocols, making it compatible with iOS devices.

Q: What is the input voltage for charging the XGPS360S?

A: The XGPS360S requires a 5 VDC input voltage for charging.

Project Name : Universal GPS Receiver

KEY FEATURES

• Compatible with iOS and Android
• Decimeter dynamic positioning
• with Swift’s Skylark™ wide area
• 10 hour battery operation
• Dual Frequency GNSS support
• GPS, Galileo and BDS
• Integrated IMU (inertial measurement unit)
• Bluetooth connectivity
• Utilizes Swift’s advanced Starling®positioning engine

GENERAL

• High-sensitivity, dual-band GNSS receiver
• Works with most apps that require GPS
• Supports both NMEA and iOS protocols
• Small and light
• Operating time : ~10 hours (for 1 device)
• Charging time : ~3 hours
• Input voltage: 5 VDC
• Internal Battery Capacity : 1400 mAh

Environmental Requirements

•  Operating temp : 14˚F – 140˚F (-10˚C – 60˚C)
• Storage temp : -4˚F – 176˚F (-20˚C – 80˚C)
• Relative humidity : 5% – 95%

Dimensions (W x H x D in mm)

• XGPS360S Body(mm) : 55.0 x 70.0 x 22.0
• Non-slip pad (mm) : 107.0 x 122.0 x 25.0

GPS/GNSS

• GNSS supported simultaneously
• SBAS (WASS, MSAS, EGNOS, GAGAN)
• GPS: L1 1575.42 MHz
• Cold Start: <29 sec. Typical (open sky)
• Warm Start: <25 sec. Typical (open sky)

Bluetooth

• Qualcomm Chipset
• Version 4.2 + EDR
• Range: ~10m (~33ft.) (open space)

FCC Compliance Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement
This device complies with RSS-247 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Industry Canada Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

Introduction

• The XGPS360S DashPro GPS Receiver features fast signal acquisition and 10Hz positioning updates, making it an ideal GPS for pilots, race car drivers and other fast moving applications. The WAAS receiver is compatible with both GPS (USA) and GLONASS (Russia) systems and it connects via Bluetooth to up to 5 Apple or Android devices.
• Once paired with your device the GPS Receiver will provide high-accuracy GPS location data to hundreds of app. The XGPS360S will remember the device to which it was previously paired for an easy automatic connection.
• This GPS Receiver also comes with a useful GPS Status Tool app. (Available free on the iTunes App Store/Google Play Store). The app allows you to turn on and off the automatic route recording feature, and to export the stored log file information. The Status
• Tool app also shows detailed information from the GPS Receiver including:
• Your location (or whether the device is still determining where you are)
• How many satellites the device sees and the signal strength of each satellite
• The battery level of the GPS Receiver, and whether or not it is charging
• Confirmation the GPS Receiver is successfully connected to your iPad/iPod touch/iPhone
• The DashPro GPS Receiver also includes a non-slip pad for use in a cockpit, car or a boat.

Installation

Put the unit in the silicon pad and place it on the car or airplane dash board.

Operation

1. Download the DashPro App from the Apple App store or Google Play store

2. Install the App on your phone.

3. After pairing the XGPS360S with Bluetooth on your phone, you can check the connection and battery charging status of the XGPS360S on your phone by operating the DashPro App.

4. You can check various information by pressing the icon at the bottom of your phone’s APP. Please refer to the image below.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>