PDi Communication Systems PD108-527 Smart TV Patient Remote Control Instructions
- June 15, 2024
- PDi Communication Systems
Table of Contents
PDi Communication Systems PD108-527 Smart TV Patient Remote Control
Specifications
- Model Number: PD108-527
- Product Type: Smart TV Patient Remote Control
- Compatible with PDI’s smart television models
- Control Codes: Bed A, B, C, or D format
- Can control up to 4 televisions in one room
Product Usage Instructions
1. Set the Television Bed Code:
- Ensure that each TV in the room has a unique code-set.
- Use the programming remote of the television to set the television to either Bed A, B, C, or D. Refer to the user instructions provided with the television for this step.
2. Set the Patient Remote Bed Code:
- Turn on the TV.
- Aim the remote at the TV and press the remote’s POWER button.
- If the TV shuts off, the remote is correctly set for that TV’s Bed code.
- If the TV does not turn off, follow these steps:
- Hold FUNC and the corresponding number for 2 seconds until the LED blinks.
- Press FUNC + 1 for BED A (LED blinks once).
- Press FUNC + 2 for BED B (LED blinks twice).
- Press FUNC + 3 for BED C (LED blinks three times).
- Press FUNC + 4 for BED D (LED blinks four times).
3. Mouse Mode:
The remote has a button that toggles between the TV’s mouse mode and keyboard mode. Only smart TVs support this function.
When the TV is operating in mouse mode:
- The arrow keys will move a mouse cursor.
- The OK key will simulate a left mouse click.
- The PAGE UP/DOWN keys will simulate the mouse wheel.
4. Anti-Theft Screw:
After installing the batteries, you can use an M2 x 5mm flat head screw to secure the battery cover and prevent theft.
Troubleshooting
If you encounter any issues or have questions about the product, please contact PDi Communication Systems, Inc. at:
- PH: 1-800-628-9870
- FX: 937-743-5664
INTRODUCTION
The PD108-527 patient remote provides IR control of PDI’s smart television models. This remote generates control codes in either a Bed A, B, C, or D format to control one of up to 4 televisions in one room.
SET THE TELEVISION BED CODE
If there is more than one television per room, each TV should be set to a unique code-set so that only one remote controls each TV. Use the television’s programming remote to set the television to either Bed A, B, C or D. Follow the user instructions provided with the television for this step.
SET THE PATIENT REMOTE BED CODE
Turn the TV On. Aim the remote at the TV and press the remote’s POWER button. If the TV shuts off, the remote is correctly set for that TV’s Bed code. If the TV does not turn off, use the following sequence to set the remote. Hold FUNC and the corresponding number for 2 seconds until the LED blinks.
- FUNC + 1 = BED A (LED blinks once)
- FUNC + 2 = BED B (LED blinks twice)
- FUNC + 3 = BED C (LED blinks 3 times)
- FUNC + 4 = BED D (LED blinks 4 times)
MOUSE MODE
The button toggles between the TV’s mouse mode and keyboard mode. Only smart TV’s support this function. When the TV is operating in mouse mode the arrow keys will move a mouse cursor, OK key will simulate left mouse click and PAGE UP/DOWN will simulate the mouse wheel.
ANTI-THEFT SCREW
After installing the batteries, an M2 x 5mm flathead screw may be used to secure the battery cover.
Troubleshooting
- Install two high-quality 1.5V “AAA” alkaline batteries. Don’t mix old batteries with new batteries.
- The red LED above the POWER key blinks when a code is transmitted.
- Remove batteries when you won’t use the remote for a long time. Liquid leakage from old batteries may cause remote failure.
- Make sure there are no objects between the remote control and the TV’s sensor that might block the signal.
- Don’t place the remote control near a heater or in a damp place. Strong impact to the remote control may cause operational failure.
- Signal from the remote control may be disturbed by sun light or other bright lights. In this case, darken the room or move the TV.
PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1-800-628-9870 FX 937-743-5664
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>