Miele PFD 102 Stainless Steel Dishwasher Installation Guide

: June 15, 2024
: Miele

Table of Contents

Miele PFD 102 Stainless Steel Dishwasher
Installation notes
Appliance dimensions and installation dimensions
Connections
Technical data
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Miele PFD 102 Stainless Steel Dishwasher

Installation notes

For safe installation and commissioning of the dishwasher please read the installation plan, the service documentation, the installation sheet, and the operating instructions.
This installation plan includes the dimensions of the appliance, the technical data, and the requirements to be met on-site for the installation of the dishwasher.

Installation requirements

This dishwasher must only be installed and commissioned by the Miele Customer Service Department, a Miele authorized dealer or a suitably qualified specialist.
Installation should only be performed in accordance with valid regulations, relevant standards, and health and safety codes.

Environmental requirements

Condensate can build up in the area surrounding the dishwasher. Any furniture and fittings in the room must therefore be suitable for pur-pose.

Vapor barrier film for built-in applications The vapor barrier film supplied protects the worktop from damage caused by steam when the door is opened. Attach the vapor barrier film above the door, and underneath the worktop.

Electrical connection

All work on the electrical connection must be carried out by the Miele Customer Service Department, an authorized Miele dealer or a qualified electrician.

Plug Connection The dishwasher should be connected to the electricity supply via a socket.

Hard-wired

If the dishwasher is hard-wired to the power supply, a power switch capable of disconnecting the dishwasher at all poles must be installed on-site. This power switch must have a contact gap of at least 3 mm.
The socket and the power switch must be accessible after the appliance has been installed. An electrical safety test must be carried out after installation and after any servicing work. The main connection cable must be laid protected from the risk of thermal damage

Residual current device ( RCD) For increased safety, it is recommended to protect the dishwasher with a residual current device (RCD) with a trip current of 30 mA.

Equipotential bonding There is a screw connection point for equipotential bonding at the back of the dishwasher. Equipotential bonding should be carried out if possible on site.

Water connection

The dishwasher must only be connected to fully vented pipework. A brief increase in the water pressure can damage the components of the dishwasher.

Water inlet

The quality of the incoming water must correspond to the drinking water specification of the country in which the dishwasher is being operated.
The dishwasher must be connected to the water supply in strict accordance with current local and national water authority regulations. It can be connected to cold or hot water supplies. Connecting the dishwasher to a hot water supply will reduce programme running times. For short programme running times, a water pressure of at least 200 kPa is also required.
If a stopcock is not available, only a qualified installer may connect the dishwasher to the drinking water supply.
The stopcock should remain accessible once the dishwasher has been installed so that the water supply can be shut off whenever the appliance is not in use.

Drain

The dishwasher drain hose should be connected to a separate on-site drainage system for the dishwasher only. If a separate connection is not available, we recommend connecting the hose to a dual-chamber siphon. If the hose is to be fitted directly to the drainage system on-site, use the hose clip supplied with the dishwasher. The on-site connector for the drain hose can be adapted to different hose diameters. If the connector extends more than 30 mm into the drain hose, it must be shortened. Otherwise, the drain hose can become blocked.
Lay the drain hose so that it does not kink and is not being subjected to pressure or tension.
If the on-site drain connection is situated lower than the guide path for the lower basket rollers in the open door, a siphoning effect during a program can cause the wash cabinet to empty itself of water.
In this case, lay the drain hose with a bend in it so that its highest point is at least level with the guide path for the lower basket rollers. For AU, NZ the drain should be connected in accordance with AS/NZS 3500.2.

External dispensing

An external dispensing module for liquid cleaning agents can be connected to the back of the dishwasher. The dispensing module is available as an optional accessory and is supplied with installation instructions.

Appliance dimensions and installation dimensions

Appliance dimensions and installation drawings

PFD 102 i

Miele-PFD-102-Stainless-Steel-Dishwasher-FIG-1

PFD 103 SCi

Appliance type PFD 102 i PFD 103 SCi

Front panel dimensions

Length	[mm]	500–654	540–694
Thickness	[mm]	16–20	16–20
Weight	[kg]	4–11	4–11

Connections

Connections on the back of the appliance

Miele-PFD-102-Stainless-Steel-Dishwasher-FIG-3

On-site connections

Miele-PFD-102-Stainless-Steel-Dishwasher-FIG-4

Electrical connection
External dispensing, power supply connection
Equipotential bonding
Wastewater
Cold or hot water
External dispensing, connection for dispensing hose sealed with a blind stopper*

the dispenser connector is supplied with the dispensing module

External dispensing

Max. delivery head	[m]	1.5
Length of dispenser hose, DOS module to suction lance	[m]	1.8
Length of dispenser hose, back of appliance to DOS module	[m]	2.8
Length of power cable, back of appliance to DOS module	[m]	2.8

Place the container on the floor next to the cleaning machine or in an adjacent cabinet. The container must not be placed on top of or above the cleaning machine.

Technical data

Appliance type PFD 102 I PFD 103 SCi

Dimensions and weights

Height	[mm]	805	845
Height adjustment	[mm]	65	65
Width	[mm]	598	598
Depth	[mm]	570	570
Depth with door open	[mm]	1165	1205
Max. plinth return	[mm]	115	115
Weight	[kg]	42	52
Max. floor load	[N]	1000	1000
Emission levels
Sound power level	[dB(A)

re 1 pW]

| 46| 45
Sound pressure level in the workplace| [dB(A)]| 34.1| 32.5
| Technical data
---|---
Electrical connection

Standard electrical connection PFD 102 i

| |
Voltage| | AC 230V
Frequency| [Hz]| 50
Fuse rating| [A]| 32
Plug| | –
Power cable length| [m]| 1.7
Power cable cross-section| [mm2]| 3×4
Heat output| [kW]| 6.1
Total rated load| [kW]| 6.3
Standard electrical connection, Possible voltage variant PFD 102 i
Voltage *| | AC 230V
Frequency| [Hz]| 50
Fuse rating| [A]| 13
Plug| | +
Power cable ** length| [m]| 1.7
Power cable cross-section| [mm2]| 3×1.5
Heat output| [kW]| 1.9
Total rated load| [kW]| 2.1

Program running times are longer with this voltage variant

Optional accessory

Water inlet

Max. water temperature	[°C]	60
Max. water hardness	[mmol/l]	6.5
Max. water hardness	[°dH]	36
Water connection pressure	[kPa]	100 – 1000
On-site threaded union (flat seal)	[inches]	3/4
Connection hose length	[m]	1.5
Connection hose extension *	[m]	1.5

Optional accessory

Drain

Max. water temperature	[°C]	82
Drain hose length	[m]	1.5
Max. drain hose length	[m]	4
Max. delivery head	[m]	1
Max. transient flow rate	[l/min]	10
Hose inner diameter	[mm]	22
On-site hose sleeve ( x length)	[mm]	22 x 30
Operating conditions
Ambient temperature	[°C]	+5 – +40

Relative humidity:

Up to 31 °C, maximum

| [%]|

80

Linear decreasing to 40 °C| [%]| 50
Max. altitude above sea level up to| [m]| 4000
Storage and transportation conditions
Ambient temperature| [°C]| -20 – +60
Relative humidity| [%]| 10–85
Air pressure| [hPa]| 500–1060
Min. site access dimensions including transport pallet
Height| [mm]| 970
Width| [mm]| 670
Depth| [mm]| 670

United Kingdom