YXL 60W LED Wall Pack Light Instruction Manual

YXL 60W LED Wall Pack Light

Product Information

Product Manual: INSTRUCTION MANUAL
This LED Wallpack Light is designed to provide bright and energy-efficient lighting for outdoor spaces. It is important to follow the installation and maintenance instructions provided in this manual to ensure safe and proper usage of the product.

Specifications:

• Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards-Installation and maintenance must be performed by a qualified electrician.
• Power supply: Minimum 90 supply conductors.
• Dimming options available: 0/1-10V Dimming
• Photocell Sensor: Enables dusk-to-dawn operation

Installation:

1. Loosen the two mounting base screws using a screwdriver to open the fixture.
2. The fixture opens sideways from the mounting base and stays connected on the hinge.
3. Align the holes on the mounting plate with those on your junction box. Use two screws to attach the mounting plate to your junction box, depending on the size of the holes.
4. Follow the wiring instructions provided to make the electrical connections.
5. If using a dimmable driver, refer to the Wiring Diagram for proper connection.
6. Close the fixture by tightening the two mounting base screws using a screwdriver.
7. To enable dusk-to-dawn operation, remove the black opaque cap cover installed on the fixture. If you do not need this function, you can choose to use the cap cover to block it out.
8. Caulk around the back face of the light fixture as shown in the diagram with silicone sealant (not included).

FAQ

• Q: Can I install this product myself?
  A: Installation and maintenance of this product must be performed by a qualified electrician to ensure safety and compliance with applicable installation codes.

• Q: How does the dusk-to-dawn operation work?
  A: The photocell sensor enables the light fixture to automatically turn ON when it is dark outside and turn OFF when the sun rises, saving energy. To enable this function, remove the black opaque cap cover installed on the fixture. If you do not need a dusk-to-dawn operation, you can use the cap cover to block it out.

• Q: Can I dim the LED Wallpack Light?
  A: Yes, this product supports 0/1-10V dimming. If you have a dimmable driver, refer to the provided Wiring Diagram for proper connection.

Thank you for purchasing our product. Please read the below articles carefully to see how to use this product safely. Warning contents and attention contents related to product safe use, please be sure to follow it.

WARNING

• Risk of Fire, Electrical Shock, Cuts or other Casualty Hazards-Installation and maintenance of this product must be performed by a qualified electrician. This product must be installed by the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Risk of Fire and Electric Shock-Make certain power is OFF before starting installation or attempting any maintenance. Disconnect power at fuse or circuit breaker.
• Risk of Fire-Minimum 90℃ supply conductors.
• Risk of Burn-Disconnect power and allow the fixture to cool before handling or servicing.
• Risk of Personal Injury-Due to sharp edges, handle with care.
• Failure to comply with these instructions may result in death, serious bodily injury and property damage.

Attention

1. This product within the input voltage range: 100-277V, 50/60Hz.
2. If input voltage exceeds this range, it may cause the lamp failure. Please be sure to operate under correct input voltage.
3. Ensure ambient operating temperature of -35℃-50℃..
4. Using this product in temperatures outside of this range will reduce the product lifespan.
5. Make sure to turn off power before starting the installation process.
6. IP rading of Ip65, can work under damp/wet locations.
7. Please keep the product away from any corrosive substance. When you clean it, please use damp or dry cloth.

Wiring Diagram

Installation

1. Loosen the two mounting base screws using a screwdriver to open the fixture.

2. The fixture opens sideways from the mounting base and stays connected on the hinge.

3. Align the holes on the mounting plate with those on your junction box. Use two screws to attach the mounting plate to your junction box, depending on the size of the holes.

4. Follow the wiring instructions to make the electrical connections.

5. Close the fixture by tightening the two mounting base screws, using a screwdriver.

6. Dusk-to-dawn operation enables the light fixture to automatically turn ON when dark outside and turn OFF when the sun rises, thus saving you energy.

7. To enable dusk-to-dawn operation, remove the black opaque cap cover installed on the fixture.
   Note: If you don’t need a dusk-to-dawn function, you could choose to use a cap cover to block out.

8. Caulk around the back face of the light fixture as shown in the diagram with silicone sealant (not included).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>