YUNLI02 Robot Vacuum Cleaner User Manual

Robot Vacuum Cleaner
User Manual
X20

Thank you for choosing YUNLI02 robot vacuum cleaner
Welcome to use
Thanks for using YUNLI robot vacuum cleaner.
YUNLI02 X20 is a smart robot vacuum cleaner that can plan its own path. It relies on high-precision laser ranging sensors to build a room map in real time and clean it intelligently and efficiently. With a full-featured base station, it can collect garbage and clean mops automatically. Through the mobile phone AP, you can remotely control the robot in real time.
YUNLI02 X20 s an essential product for you and your family to get rid of tedious floor cleaning and housework, and enjoy life with peace of mind.

Product List

Product Introduction

Note: Press any key to stop during cleaning or docking.

Product Introduction

Charging Station

Quick installation and use

Installtion

1. Install the Station board from the front side up to the slots on both sides of the station.
   When you hear a click, it is installed in place, and then press other positions slightly to ensure the base plate is completely attached to the ground. Then put the removable wash tray to the inner base.

2. Place the base station against wall on flat floor. Make sure there Is at least 1.6ft/0.5m of space on both sides and at least 4ft/1.2m of space in front, and WiFi signal is in good condition, and then turn on the power,

3. After placing the clean water tank, sewage tank and dust bag according to instruction, plug in the power cord. After the base station powered on, the white indicator light will be always on.
   Note: Water is required in clear water tank.

Instruction before using

1. Before using, please remove the bumper protectors and front impact protection film on the robot
2. Power on/off
   Long pressing the button to turn on the robot, the biue light breathes, the host enters the boot process. When the bive light is always on. then the boot is completed. When the host is in standby, press and hold the button to shut down. When the light is off, then the shutdown is completed.
   Note: The host cannat be tumed off during charging.

Charing
Method 1: After long pressing the button the machine is turned on, put the robot back into the base station for charging, and the robot will prompt “charging’.
Method 2: Press the buton on the rabot or the button on the base station to activate the automatic recharging mode, and the robot will ‘automaticallyreturn to the base station for charging
Method 3: Click the recharge button on the APP to activate the automatic recharge mode, and the robot will automatically return to the base station for charging.
Tips:

•  Please charge the robot when you use itfor the first time. It takes about 56 hours o fully charge.
• In order to faciltate the return of the robot to the base station, it is recommended to et the robot start from the base station, and do not move the base station at wil.
• Please place charging station in the same area, extra charging stetion will affect the recharge function of the robot.
• When the power of the robot is low and cannot be turmed on, put the robot directly into the base station for charging.
• The robot s equipped with high-performance lithium battery. To maintain battery performance, keep the robot charged during daily use.

Quick Use Guide

Download the APP

1. Scan the QR code or search for ‘yunliBot in “APP Store or “google play” to download the APPhttps://smartapp.tuya.com/smartlife
   

2. Press and hold the ( ) button and button of the robot vacuum at the same time for 3S to enter the network configuration mode, the button light flashes and there is a voice prompt.

3. Enter the home page of AP, add device according to the APP prompt. Please check Network Configuration Quick Guide for details.

Clean Mode

Press and hold the button for a few seconds, the robot button light will turn on, and wait for the completion of the startup voice broadcast, then you can control the robot to work.

1. Auto Cleaning
2. Press the button of the robot vacuum to start the cleaning mode, and the robot starts to clean.
3.  Press the ®button of the charging base lightly, and the robot starts to clean.
4. There are three cleaning modes available for the APP :

• Sweeping mode: the robot enters sweeping mode, automatically returns to the base station to empty dust after cleaning.

• Mopping mode: the robot enters mopping mode, automatically returns to the base station after the mopping.

• Sweeping and Mopping mode: the robot enters sweeping and mopping mode, automatically returns to the base station to empty dust and then clean the mop.
  Note: The robot will enter drying mode after each cleaning.
  Tips:
  *  If the power is too low, the cleaning task cannot be performed, please charge it before starting the cleaning;

• If the power is too low during cleaning, the robot returns to the charging dock for recharge and resumes cleaning where it left off. 2. Scheduled Cleaning
  Set the scheduled cleaning time on APP. The robot will automatically start cleaning at the time you set and return to the charging base after cleaning.
  Note:
  « during the scheduled cleaning period, the host will not automatically renew the cleaning and play voice.

  3. Smart Area

  4.  Area Cleaning
     After Smart Map generated successfully, you can add an adjustable size and location cleaning area. The robot will only clean the selected area.

  5. Designated Room Cleaning
     After Smart Map generated successfully, you can divide the map into different areas according the cleaning needs. You can set one or more cleaning areas. The robot will only clean the selected area.

  6. No-go Zone
     You can set the area that does not need to be cleaned as”No-go Zone’through the APP. and the robot vacuum will not enter the no-go zone.
     Note:

• Please make sure the robot has generated the smart map. The No-go zone will be lost when the map is rebuilt.

• The No-go zone may be lost due to changes in the location of the self-empty station or furniture. So please try not to move or interfere with the Robot while it is working.
  *Due to the continuous development and upgrade of APP. there may be slight adjustment of functions and details, please refer to the actual version. 4. Pause
  When the robot is in the cleaning mode, press any key to pause the cleaning, press the ( ) key and the machine will continue to clean, press the key and the robot will return to the charging base and end the cleaning.

  5. Docking Mode
     Auto mode:When the battery power is low, the robot will prompt”Low power, start docking mode”, and returns to the charging station for recharge. Manual mode: In standby mode, press the back button on the host or the base station, or click the back button on the APP. After the voice prompt” Turn on the docking mode”, the robot will automatically return to the base station to charge.

  6. Troubleshooting
     Wihen an abnormality occurs during the operation of the robot, the indicator fight flashes red quickly and there is a voice promat. For the solution, please efer to “Troubleshooting®
     Note: Itisin the fau’t state.

  7. Power Off
     Ifthe robat s not used for long time, please turm off the main power switch (1t shuts down after 12 hours)

  8. Reset Wi-Fi
     Vihen the router changed configuration, password forgot or mobie faed to connect with robot, press and hold and at the same time unti the voice prompts, wait for the indicator light lashing blue and follow the APP prompts to recontfigure the network.

  9. Do Not Disturb Mode
     Using the APP can manually turm on/off do not disturb mode or modify do ot disturb period. In Do Not Disturb mode,the robot will ot resume clean and play voice reminder.

  10. cleaning mode
      Through the APP control, you can choose quiet, standard and strong modes, and the defaultis the standard mode.

  11. Dormant Sleep
      No operation for more than 10 minutes, the hast il automatically enter sleep state.n sleep state, the indicator light will be off and pressing any key can wake up the robot.

  12. Base Station
      Clean the robot

  13.  When the robot is in sweeping and mopping mode, to ensure the cleanliness of the mop, it willperiodically eturn o the base station to clean the mop and replenish the water i the robot’s water tank.

  14. After the cleaning task is over, the robot will automatically return to the base station for dust collection, mop cleaning, water inection and mop drying operations.

Base station self-cleaning
Tap the self-cleaning button on the base station to activate the self-cleaning function of the base station. When the base station is self-cleaning, please use the cleaning brush to assist the cleaning.

Maintenance

Accessories Cleaning and Maintenance
In order to maintein the normal operation of the robot vacuum, its recommended to clean and maintain the fobot vacuum regularly. Please tun offthe power during maintenance.
Refer to the table below for the frequency of cleaning and maintenance of accessories

Maintenance Dust Bin
Take out the dust box, open the dust box cover, and dump the garbage.

Cleaning Fiters

1. Take the filters out from the dust bin.
2. Clean the Primary Filter, High effciency (2)Cleanthe Pri 3 fiter and Sponge with provided Cleaning Tool. If washed, please dry them.
3. Put the High efficiency filter and Sponge back together in the dust bin.

Cleaning Main Brush
Remove the roller brush cover and take out the roller brush. If there is a lot of dust in the suction port, please use a rag to clean. If there are hairs entangled in the brush, please use the upper blade of the cleaning tool to cut it off.

Cleaning Side Brush
After removing the side brusn, use the pper blade of the cleaning tool to clean the side brush and wipe with a cloth

Cleaning Universal Wheel Clean the universal wheel with a cloth,

Cleaning Anti-fal sensor
Use a dry cloth to clean ciiff sensors to ensure the sensitivity.

Charging base station
Clean the base station with a cleaning brushrecommended monthly cleaning)

Firmware Upgrade
The robot firmware can be upgraded through the APP. When upgrading please ensure that the fobot is in charging state and has enough amount of power. The indicator light flashes when the firnware is in upgrading
Reset
If the system still cannot be used normally after resetting the system, please poke the reset hole under the flip cover in the power-on state to tum off the robot, then press and hold the button to restart the robot.

Product parameters

Packing List

Robot

Charging Base Station

1. This product meets the requirements of *Administrative Measures for the Restriction of the Use of Hazardous Substances in Electrical and Electronic Products”
2. In the term of environmental protection use, consumers in the normal process of use wil not appear harmful substances leakage, precipiation  proiems affecing consurer eafth canbe sssured use,
3. The environmental protection service lfe of our producs s 10 years. The “environmental protection service fe” i effective only when the products are used under normal conditions as described in this manual

Component name/Hazardous
substance Plastic parts| Lead| Mercury| Cadmium| Hexavalent chromium| Polybrominated biphenyls (PCBS)| Polybrominated diphenyl ethers
---|---|---|---|---|---|---
0| 0| 0| 0| 0| 0
Hardware| 0| 0| 0| 0| 0| 0
Sweeping electrical circuit module| 0| 0| 0| 0| 0| 0
Electronic components| 0| 0| 0| 0| 0| 0
Battery| 0| 0| 0| 0| 0| 0
Plug power cord (metal part)| x| 0| 0| 0| 0| 0

This table is prepared in accordance with SJ/T 11364
O: Indicates that the content of the hazardous substance in all homogeneous materials of the part is below the limit requirements specified in GB/T26572
X: Indicates that the amount of the hazardous substance in at least one homogeneous material of the part exceeds the limit requirements specified in GB/T26572
(Note: Some of the parts marked “X” above contain harmful substances exceeding the standard because of the current industry technical level, which cannot be replaced or reduced temporarily. )

Troubleshooting

| Problem| Reason| Solution
---|---|---|---
1| The sweeper won’t charge| The base station not powered| Check if the indicator light of the dust collection station is on, if not, please re-plug
Poor connection of charging contacts| Please use a dry cloth to wipe the charging poles of the base station and the sweeper
2| Sweeper is stuck| The sweeper is stuck on the loose objects on the ground| Before the sweeper starts to work, pick up clothing, scraps of paper, wires and fragile items on the floor to avoid getting stuck while working
Sweeper stuck on furniture| The sweeper can pass through the bottom of furniture with a height of more than 11cm. If it is lower than this height, it may be stuck.
3| The sweeper cannot return to the base station| The base station not powered| Check whether the indicator light of the base station is on. If not, remove and plug again
The base station is not placed correctly| Remove the obstacles within 1.6ft/0.5m on the left and right side of the base station and within Oft/1.2m in front of it. Please place the base station according to the instructions
The cleaning is not started from the base station| Let the sweeper start cleaning from the base station
The recharge path is blocked, for example, the door of the room where the base station is placed is closed| Keep the recharge path clear
The base station was moved artificially| Try to avoid moving the base station, let the sweeper complete the self-cleaning
Wi-Fi does not have a signal| Reconnect to Wi-Fi
4| The brush is abnormal| Side brush installation is not in place| Check if the side brush installed well
brush may be stuck by entanglement| Check the brush for entanglement and clean the side brush
5| Weak suction| The dust bin is full| Empty the dust bin and replace with a new dust bag
Filter is clogged or damp| Clean and dry the filter or replace with a new one
6| Failed to make a scheduled cleaning| The sweeper power is off| Ensure that the power switch of the sweeper is turned on and there is sufficient power to complete the cleaning
Sweeper is in low power| Please charge
The setting is not successful or has been cancelled on the APP| Please reschedule the cleaning according to the APP operation guide
7| Left/Right wheel abnormal| Left/right wheels may be stuck| Check left/right wheels for entanglement, and clean left and right wheels
8| Abnormal roller brush| The roller brush may be entangled| Check if the roller brush is tangled and jammed and clean the roller brush
9| Sweeper suspended in the air| The sweeper leaves the ground or gets stuck on the edge of a cliff| Please place the sweeper on the ground
10| Laser radar anomaly| The sweeper leaves the ground or gets stuck on the edge of a cliff| Please place the sweeper on the ground
11| Infrared anti-collision bumper is abnormal| Infrared anti-collision bumper may be stuck| Tap the left, middle, and right side of the infrared anti- collision bumper to make it return to its place
12| The dust bin is abnormal| The dust bin may not be installed properly| Pull out the dust bin and reinstall it
13| The base station cannot be controlled| The communication between the host and the base station is abnormal| Place the host in front of the base station for control or press and hold the host recharge button
and the base station recharge button for a few seconds until continuous beeping sounds, the host and the base station are successfully paired
14| Unable to configure APP| The sweeper is not within the network coverage of the router| Make sure the sweeper is within the network coverage of the router
Sweeper cannot configure itself| Turn on the sweeper and reconfigure the network
5G Wi-Fi networks are not supported| This model does not support 5G Wi-Fi network, please use 2.4G Wi-Fi network for configuration
15| Cleaning map lost| Moving sweeper to another floor, the map lost| The sweeper will automatically rebuilt the new sweep map
16| Unable to create smart map on APP| Moving the sweeper during cleaning causes it to be unable to locate| Try not to move the sweeper when it is working
The automatic cleaning task has not been completed| When the sweeper finishes cleaning, it automatically generates a map
17| The sweeper makes a strange sound when it is running| Side brush, rolling brush is entangled; The dust bin and filter are blocked| Cleaning and maintenance of the side brushes is recommended, and regular replacement of the roller brushes, dust box and filter accessories
Sweeper enters strong power cleaning mode| Switch to standard cleaning mode
18| Pink light on station always on| The dust bag is removed or not installed properly| re-insert the dust bag to ensure it is properly installed
Take out the clean water tank/no water| check the water volume of the water tank, if the water volume is insufficient, please add water
Take out the sewage tank full of water| check whether the water in the sewage tank is full. If full, pour out the sewage
The cleaning tank is full| start self-cleaning to drain the cleaning tank

Security Information

Information about rechargeable batteries

1. Lithium battery
   Important: Lithium batteries and products containing lithium batteries are subject to srict ransport regulations If the product (including batteries) needs to be transported for long-term storage, travel, or any other reason, the following shipping instructions must be followed
   • Remove the batery from the sweeper.
   • Apply a piece of insulating tape to the electrodes of the battery.
   • Reinsert the battery with the tape and close the betery cover
   • When shipping. pack the product inits original packaging or sutable packaging.
   •  Can only be shipped by land, not by air

2. Storage battery

• If the product needs to be stored for a long time, please remove the battery first.
  Battery removal steps:
  1. Turn the machine aver to the back.
  2. Use a screwdriver or other suitable tool to remove the two battery cover screws.
  3. Take out the batery cover.
  3. Take out the battery.
  •  Store the product and battery in a cool,dry place.

  3. Remove the battery.
     •  Before disposing of the appliance, the battery must be removed from the appliance.
     •  The appliance must be switched off when removing the battery.
     •  Batteries should be disposed of safely.

Use Restrictions

• This product s only used for loor cleaning in the home environment. do not use it outdoors (stich as open balcanies), non-floar (such as sofas), commercial orindustiial environments
• Do not use it in a suspended environment (such as duplex floors, open balconies, furniture tops) without guardrails
• Do not use in environments above 40°C, below 0°C, or in environments with any liquid and sticky substances on the ground
• Please hang up the ground cables at home before use to avoid dragging the cables when the host is running
• Please put away fragile tems and sundries (such as vases, plastic bags, etc.) placed on the ground to avoid damage to valuables at home when the host is blocked or slightly collided during operation
• Do not alow persons with physical, mental or sensory disabilies, including children, o use or operate this product
• Do not let children use the robot as a toy. Please supervise children and pets to keep them away when the host is working
• Do ot place the main brush cleaning toolin an area that can be touched by children
• Do not place any objects (including children, pets) on the stationary or moving main unit
• Do not let human o pet hair fingers and other pats close to the vacuum part of the machine when the host is working
• Do not use to sweep any burning objects (such as unextinguished cigarette butts)
• Do not use for cleaning long-haired carpets (sorme dark-colored carpets may not be cleaned properly)
• Do ot letthe host pick up foreign objects or sharp abjects (such as decoration waste, glass, ron nails etc)
• Do not use the protective cover of the laser ranging sensor, the upper cover of the main unit and the collsion buffer as a handle to carry the machine
• Do ot clean or maintain the main it and the charging stand when the power is turned off or off
• Do not wipe any part of this product with a damp cloth or any liquid
•  Please use this product in accordance with the instructions in the manual, any loss and injury caused by improper use shall be borne by the user

Warranty Card Instructions

Unlirobot vacuum cleaner implements after-sales three-guarantee service in strict accordance with the ‘Consumer Rights Protection Law of the People’s Republic of China” and “Product Quality Law of the People’s Republic of Chinr. The contents are as follows
Warranty Regulations

1. Product retur and exchange commitment

2. Within 7 days from the day after receipt, consumers may choase to return, exchange of repair the productsif the quality problems o failures of the products are verified by the manufecturer’s quality inspection.

3. Within 15 days after receipt of the signatre, f the quality problem or faultof the product occurs and i identified as product performance fault by the after-sales service center, the product can be replaced free of charge.

4. Product warranty commitment
   From the date of purchase by the user,under normal and reasoneble use, ifthe product has quality problems, the whole machine wil be guaranteed for one year free of charge.

5. After-sales service method:
   The after-sales service method of the whole line of inteligent robot vacuum cleaners i repair by mail ‘Ship Repair: When the repair service is required, the consumer willsend the product to the designated repair location. During the warranty period, the postage costs incurred by the maintenance of product quality problems will be borne by the Xingi ntelligent sweeping robot.

6. Warranty coverage:
   During the warranty period (subject to the invoice or valid sales voucher), users will be provided with free maintenance for any fault caused by the product itself under normal use.

Warm hint: When you need repait please fil in the warranty card ‘accurately and completely, and send the card with the machine, so that we can serve you better.
Warranty Card
User Name……………………………………………………..
Full Address………………………………………………………
Phone Number……………………………………………………..
Zip Code……………………………………………………..
Product Model……………………………………………………..
Purchase Date……………………………………………………..
Serial Number……………………………………………………..
Warranty Date……………………………………………………..
Maintenance Record

| Maintenance  Date| Description of The Fault  and Parts Replacement| Maintenance  Center| Maintenance  Engineer
---|---|---|---|---
1| | | |
2| | | |
3| | | |
4| | | |

After-sales Service

86 00000x
  xooox@xoo.com
  wwwoooox.en
If you have any problems during use, please call the after-sales service: XXXXXX. And there will be professionals to answer your questions. For more details, please visit the official website: www.yunli.com
Manufacturer NamexxxxxXXxXxX
Manufacturer address:: XXXXXXXXXKXXXIXXXKXXXKKXXXK
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
‘These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RE Exposure guidelines, This equipment should be installed and operated with minimu distance between 20cm the radiator your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>