Newest 100W 12V Dimmable LED Driver Instructions

June 15, 2024
Newest

Newest logo 100W 12V Dimmable LED
Driver Instructions

100W 12V Dimmable LED Driver

Newest 100W 12V Dimmable LED Driver - fig

CCT-TUNABLE SERIES CSA-J 100W
CCT &Trac/0-10V/1-10V/10V PWM/PotentiometerNewest 100W 12V Dimmable LED
Driver

Product introduction

Feature

  • Dim-all:CCT & Trac/0-10V/1-10V/10VPWM/Potentiometer.
  • Dimming effect: PWM dim mode: 100-0.1% dim, flicker-free.
  • Trac dim mode: Forward phase & reverse phase, MLV, ELV
  • CCT-Tunable: switch on/off (Switching color temp)/ Linear adjustment of color temperature And 7 stops adjustable color temperature(2700K-6500K).
  • With unique knob trim voltage function
  • Customization: the curve which can be customize.
  • 110-277Vac Universal input. •5 years warranty.
  • damp, dry and wet location.
  • Title 24 JA8 compliant.
  • Constant voltage type. Fine tune of output voltage
  • Build in active PFC, typical power factor>0.95, THD<10%@120V Max. Load.
  • Super low loading request, works perfect at 10-100% load.
  • Short-circuit, over-temperature, over-load protection.

Unique Selling Points

  • PWM Output: 4k/HZ Constant frequency (Different frequencies can be customized:250-20000Hz)
  • Fine tune of output voltage ref. to chart 2/page3
  • Dimming range: 100%-0.1% Ultra Deep Amplitude
  • Works with single channel LED strip/tape (2 wires) and two channel CCT warm-dim LED strip/tape (3 wires)
  • Exclusive patent design of “Clamshell” junction box Fixed without screws)

Application:

  • LED strip/LED tape/LED module
  • Residential Lighting
  • Commercial Lighting

Specification

Model Number CSA-12100J CSA-24100J CSA-48100J

Output Type
Rated Power| 100W
Rated Voltage| 12V| 24V| 48V
Rated Current| 8.33A| 4.16A| 2.08A
Voltage Tolerance| ±0.5V
Voltage Regulation| ±0.5%
Load Regulation| ±1%
Input Type
Voltage Range| 110-277V
Frequency Range| 47-63HZ
EfficiencyTyp. )| 90%@120VAC 91%@277VAC
Total Harmonic Distortion| THD< 15%(@100% load)
Power Factor(typ.)| 0.99@120VAC 0.98@277VAC
AC CurrentTyp. )| 1.04A
Inrush Current(Typ.)| 26A
Leakage Current| <0.5mA
PROTECTION
Short Circuit| shut down o/p voltage, re-power on to recover after fault condition is removed
Over Load| Intelligently reduce the output voltage, auto-recovery or re- power on to recovery
Over Temperate| 100℃±10℃ Intelligently reduce the output voltage and current. Auto-recovery after over load is removed
ENVIRONMENT
Working Temp.| Tcase=-40 ~ +60 (Please refer to“OUTPUTLOAD vs TEMPERATURE “section)
Working humidity| 20 ~ 95% RH non-condensing
Storage temp., Humidity| -40 ~ +90, 10 ~ 95% RH
Temp .coefficient| ±0.03%/℃(0~50℃)
Vibration| 10~500Hz, 5G 10min./1 cycle, period for 60min. each along X,Y,Z axes
SAFETY & EMC
Safety standards| UL8750, CSAC22.2 No. 250.0-08
Withstand voltage| I/P-O/P:1.88KVAC
Isolation resistance| I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH
EMC Emission| Compliance to FCC part 15     Subpart B
OTHERS
Dimension| 188×120.5x42mm (LWH)
Net. Weight| 0.9KG
Packing| –

Mechanical Diagram

Newest 100W 12V Dimmable LED Driver - Mechanical

Wire Specification

CSA-J Input Output 0/1-10V Dimming
Power Function Color Spec.


100W

| AC L| Black| 18AWG| DC+| Red| 18AWG| Dim+| Purple| 18AWG
AC N| White| 18AWG| DC-| Black| 18AWG| Dim-| Pink| 18AWG
Ground| Green| 18AWG| CW-| Yellow| 18AWG| /| /| /

function Introduction

Newest 100W 12V Dimmable LED Driver - Introduction

See below:
12V output: 9V-13V
24V output: 17V-25V
48V output: 36V-49V
See below:
0:Single dimming{single channel LED strip/tape (2 wires)}
1:Switch on/off (Switching color temp)
2:Linear adjustment of color temperature
3-9:7 stops adjustable color temp(2700K-6500K)
Notes gears 1-9 ,Works with Two channel CCT warm-dim LED strip/tape (3 wires)

Mounting

  1. This driver must be installed in a well-ventilated area free from explosive gases and vapors. Air circulation is essential for heat dissipation.
  2. Recommended spacing between LED drivers should be a minimum of 4” (10cm).
  3. Do not mount driver close to or above objects that can radiate. Vertical mounting is highly recommended.
  4. Select an appropriate location that is able to support the weight of the product.
  5. Use the mounting tabs on the left and right side of the driver to mount the product.

Newest 100W 12V Dimmable LED Driver - Mounting

Connection Preparation

Newest 100W 12V Dimmable LED Driver - Preparation

Input Connections & Grounding

Newest 100W 12V Dimmable LED Driver - Preparation1

Output Connections -single channel LED strip/tape (2 wires)

Newest 100W 12V Dimmable LED Driver - Preparation2

Output Connections-dual channel CW color temperature LED strip/tape (3wires)Newest 100W 12V Dimmable LED Driver -
Preparation3

Connecting Diagram

Using TRIAC/Phase cut dimming

  1. Through a phase-dimmer or lighting system, control the input AC phase line (L) and adjust the output PWM
  2. Trac dim mode: Forward phase & reverse phase, MLV, ELV dim
  3. Please try to use dimmers with power at least 1.5 times as the output power of the driver.

Wiring Diagram
Works with single channel LED strip/tape (2 wires)

  • Using Trac/MLV wiring diagram
  • Newest 100W 12V Dimmable LED Driver - diagramUsing Trac/ELV wiring diagramNewest 100W 12V Dimmable LED Driver - wiring diagram
  • Using 0-10/1-10V dimming(The driver input is connected to the dimmer)Newest 100W 12V Dimmable LED Driver - Mechanical2
  • Using 0-10/1-10V dimming(The driver is independently connected to the input)Newest 100W 12V Dimmable LED Driver - wiring diagram1 Works with Two channel CCT warm-dim LED strip/tape (3 wires)
  • Using Trac/MLV wiring diagram
  • Double channel CW color temperature LED strip/tape (3wires)Newest 100W 12V Dimmable LED Driver - wiring diagram2
  • Using Trac/ELV wiring diagram
  •  Double channel CW color temperature LED strip/tape (3wires)Newest 100W 12V Dimmable LED Driver - wiring diagram3
  • Using 0-10/1-10V dimming
  • Double channel CW color temperature LED strip/tape (3wires)(The driver input is connected to the dimmer)Newest 100W 12V Dimmable LED Driver - wiring diagram5
  • Double channel CW color temperature LED strip/tape (3wires)(The driver is independently connected to the input)Newest 100W 12V Dimmable LED Driver - wiring diagram6

PFC load chart

Newest 100W 12V Dimmable LED Driver - load chart

4Load vs Ambient Temperature

Newest logoPlease feel free to contact us if you have any questions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals