Aimiler 12205182602 Level 2 Electric Vehicle Charger User Manual

Aimiler 12205182602 Level 2 Electric Vehicle Charger

Product Information

Specifications

• Product Item: ZA-UKBF-F
• Output Power: kW
• Operating Current: AMax
• Current Adjustability: A-A-A-A
• Installation Method: Portable/Wallbox
• Operating Voltage:
• Operating Frequency:
• Cable Length:
• AC Input Plug: NEMA -P
• Connector Type Indicator: Type (SAE J) -Color Indicator
• User Interface: inches OLED Screen
• Charging Method: Plug and Charge/ APP Charging
• Communication Method: WiFi & Bluetooth
• Appearance Size: mm X mm X mm
• Product Weight: kg
• Over Voltage Protection: Input Voltage %, relay is off
• Under Voltage Protection: Input Voltage %, relay is off
• Over Load Protection: Output Current %, relay disconnected, the power supply needed to be cut off and restored
• Over Temperature Protection: When the temperature of the main board reached , the power was reduced to %, and it was turned off after
• Ground Protection: The ground wire is not detected or the ground wire is disconnected during charging. The relay is disconnected.
• Leakage Protection: CCID, leakage, the relay was off
• Operating Temperature : – ~ +-~+
• Storage Temperature: – ~ +-~+
• Operating Humidity : % ~ % RH
• Operating Altitude: m
• Protection Degree: TYPE
• MTBF:
  • Warranty: H Years
  • Safety Standard: UL, UL-/-, UL, UL, UL

Product Usage Instructions

Operation Guide

• Operation Steps

1. Plug the charger into the socket
2. Specify the power (kW) and current (A) according to the switch and socket specifications.
3. Additional steps may be provided here

LED Indicator Instruction

Equipment Parts List

FAQ

1. How do I specify the power and current for the charger?
   You need to refer to the switch and socket specifications and set the power (kW) and current (A) accordingly.

2. What are the different charging status indicators?
   The charging status indicators are represented by different colors and flashing patterns. The user manual provides a detailed explanation of each indicator.

3. What is included in the equipment parts list?
   The equipment parts list includes the AC Charging Pile, Fixing Cover, Gun Holder, Screw, Expandable Rubber Stopper, Certification, and User Manual.

• E-mail our customer service:
  • [email protected]
• Aimiler is here to help and we are glad to serve you.

PORTABLE EV CHARGER

• USER MANUAL
  • CONTACT US: [email protected]
  • （ Version : 1.1）

SAFETY TIPS

IMPORTANT SAFETY INSTRUCTIONS
WARNING: This manual contains important instructions for AC charger series that shall be followed during installation, operation and maintenance of the unit.

• Read all the instructions before using this product;
• This device should be supervised when used around children;
• Do not put fingers into the electric vehicle connector;
• Do not use the product when the charging cable has been damaged or frayed;
• Do not use this product if the enclosure or the EV connector is broken, cracked, open, or shows any other indication of damage;
• The whole installation should be operated by qualified professional electrician;
• Be careful! Any incorrect operation may cause life danger, injury or equipment damage. The manufacturer would refuse to accept any claim arising therefrom. Please make sure this instruction manual is fully understood and the specified conditions are met before any operations of the EV charger;
• Please do not operate under any circumstances that may cause electric leakage;
• Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment;
• This equipment complies with FCC radiation exposure limits set forth for an rolled environment. This equipment should be installed and operated with a minimum distance of ??cm between the radiator and your body.
  SAVE THESE INSTRUCTIONS

IMPORTANT INFORMATION

Specified use

• This type of product is a charger that can charge electric vehicles in indoor and outdoor areas;
• When installing and connecting the charger, the relevant regulations of the local country or government shall be observed;
• The specified use of the equipment includes complying with the environmental conditions under any circumstances;
• During the storage or use of the equipment, it is necessary to store the charger and its supporting components in a dry and ventilated indoor place with a temperature of – ℃~ 30+  50℃ and a daily  average temperature of ≤ 25 ℃ within 24 hours;
• Monthly average relative humidity ≤ 90% (25 ℃), no condensation on the surface;
• After the installation, the shell of the charger shall be kept sealed to avoid soaking in rain;
• The place of use shall be free of explosive media, the surrounding media shall not contain harmful gases and conductive media that corrode metals and damage insulation, and shall not be filled with steam or serious mold;
• The place of use should avoid direct sunlight. When installing outdoors, it is recommended to install sunshade facilities for the charger;
• When the AC charger is not in use, the charging gun shall be placed 1.5 m~0.5 m away from the ground;
• Equipment shall be developed, produced, inspected and filed according to relevant safety standards. Therefore, there will be no unnecessary property loss or personnel danger, if the instructions and safety standards are followed strictly;
• The instructions contained in this manual must be strictly followed, otherwise potential safety hazards may occur or the built-in protection devices may fail. Although this manual describes the relevant safety tips, it is still necessary to pay attention to the safety regulations and accident prevention regulations in accordance with the corresponding application;
• Due to technical or legal restrictions, it is impossible to supply all models/options to the region;
• For any special requirements, pls feel free to contact us.

About this Manual
This manual is applicable to the following groups:

• The end customer (EV charger user)
• The technical staff of debugging and service
• The final explanation of this manual belongs to the company.

USE OF PRODUCTS

• Product Appearance Size

Product Appearance Introduction

• ［ A ］ Input Wire
• ［ B ］ Time Button
• ［ C ］ Current Button
• ［ D ］ Indicator
• ［ E ］ Display Screen
• ［ F ］ Panel
• ［ G ］ LOGO
• ［ H ］ Output Wire
• ［ I ］ Charging Gun
• ［ J ］ Plug

Product Performance Description

LED Indicator Instruction

Equipment Parts List

OPERATION GUIDE

Operation Steps

• Plug the charger into the socket
  • Specification of Switch and Socket

For power safety, add overcurrent protection device/circuit breaker at the product input.

GROUNDING INSTRUCTIONS

• This product must be grounded. If it should malfunction or break down ,grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This product is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• WARNING
  Improper connection of the equipment grounding conductor is able to result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly grounded. Do not modify the plug provided with the product if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

WALLBOX INSTALLATION METHOD

• Wallbox Rendering

• Fixing Cover Installation Drawing

• As shown in the above figure, place the fixing cover on the wall at a proper height, mark the hole location on the wall with a pencil, and use an impact drill to drill three φ holes on the wall according to the hole marking, and drill three φ expansion rubber plugs in the three holes. Finally, place the wall hanging shell on the wall, align the fixing holes of the fixing cover with the wall holes, and fasten them with φ tapping screws.

Gun Holder Installation Drawing

• As shown in the above figure, place the gun holder on the wall at a proper height, mark the hole location on the wall with a pencil, and use an impact drill to drill four φ holes on the wall according to the hole marking, and drill four φ expansion rubber plugs in the four holes. Finally, place the gun holder on the wall, align the fixing holes of the gun holder with the wall holes, and fasten them with φ tapping screws.

Installation Environment Requirements

The installation position of the charger shall not be close to dangerous locations or areas such as water, oil and gas pipelines；

• The installation position shall be convenient for charging, the wiring length shall be shortened to reduce the energy consumption of cable resistance when laying lines；
• The wall hanging parts and shall be fixed with screws. The installation wall shall be able to bear the gravity of the charger and its accessories, and shall not tilt after installation. The wall should not be too close to the internal line；
• The protection degree for indoor installation shall be at least TYPE , and that for outdoor installation shall be at least TYPE . It is recommended that the charger be installed in an environment with sunshade or umbrella; The lighting and passage at the installation site of the charger must be safe and smooth；
• A certain operating space shall be reserved for the installation of charger to facilitate the overhaul and maintenance of engineering personnel；
• It is recommended that the customer install a circuit breaker at the front end of the charger. The mini circuit breaker should meet local regulations.

Power Supply Requirements

The power supply mode of the portable AC charger is AC single-phase power supply, and the input electrical requirements are:

• AC Operating Voltage: Refer to page 6
• AC Operating Frequency: Refer to page 6
• The capacity of the power supply system shall be greater than the maximumoperating power of the product;
• For the specification of power socket, please refer to Specification and Configuration
• Table of Switch Socket on page 8

TROUBLESHOOTING

Troubleshooting Table

• (*) Possible fault causes (fault status LED lights up):
  • In principle, the fault must be cleared by pulling out the charging gun. The following reasons may lead to failure: Ground fault, electric leakage, charger pile ID not set. Please contact your service partner to maintain the equipment

MAINTENANCE

Maintenance

• The following routine maintenance items are only for reference, please refer to relevant standards and operation instructions for operation;
• Sunshade and rainproof measures shall be taken for the charging pile, and it is recommended to install a canopy outdoors;
• Regularly check whether the bolts of the charging pile are fastened, whether the connecting wire is loose, and whether the connection is not firm, and check whether there is short circuit;
• Pay attention to lightning protection and ensure effective shielding and reliable grounding of the charging pile;
• When using, try to control the output voltage and current of the charging pile within the nominal range, so as to ensure that the charging pile can work with the maximum efficiency;
• When the charging pile is out of service, the charging output shall be stopped first, then the power plug shall be pulled out and the power shall be cut off, then the cable shall be wound, and the  charging pile shall be put back to its original position after the temperature of the charging pile drops to normal temperature;
• The electrical schematic diagram of the charging pile is shown in the figure below.

Important Matters

• To ensure that you can enjoy the warranty service, please ensure that the tear-proof label on your charging pile is intact;
• The warranty period of your charging pile shall be subject to the transportation and delivery period. If it cannot be provided, it shall be subject to the ex factory date of the equipment;
• Please show the original of the unit and invoice during warranty.

NOTICE

• The charger must be grounded through the grounding conductor of the permanent wiring system or equipment;
• Please avoid installing in the direct sunlight or exposure environment, and try to use the charger in a cool and ventilated place;
• Do not install and use the charger near flammable, explosive, combustible and chemical substances or steam;
• Before installing or cleaning the charger, the power supply must be cut off to ensure that there is no power input. Do not touch the heat source, dirt or water source on the contact surface;
• Please use the charger within the specified working parameters;
• Only connect electric vehicles. Do not connect other loads (electric tools, etc.). Do not use the charger for other purposes than charging or other vehicles that do not support the AC charger standard of the country where the product is located;
• The charger must be checked regularly. If it is found to be defective, cracked, worn, damaged and inoperable, the charger shall be stopped immediately and the after-sales service telephone shall be called;
• Do not attempt to open, disassemble, modify or transform the charger without a professional electrician. The charger is not a device that can be maintained by users. Do not remove safety symbols, warning prompts, nameplates, signs or pipeline marks;
• If you or your car are exposed to rainstorm, lightning, heavy snow or other severe weather  conditions, do not use the charger to prevent any parts from being damaged;
• Please handle with care when transporting the charger. Do not subject it to strong external force impact, and do not drag, twist or step on the charger and cable to prevent damage to any parts. At any time, please avoid and prevent the charger from being damaged by moisture, liquid and other foreign matters. If there is water, damage or corrosion, please do not use it. Do not touch or charge the cable and charging gun head with wires, tools or other sharp hard objects;
• If your EV is covered with a car cover or a car coat, please remove it before charging the car;
• Users may affect or impair the function of the charger during usage if he/she wears any medical or implantable electronic device, such as cardiac defibrillators, pacemakers, etc;
• During transportation, there should be no severe vibration, impact, exposure to sunlight, rain, or dumping of the charging pile.

FCC STATEMENTS

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and;
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

• These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
• Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>