tp-link C310 V1 Outdoor Security Wi-Fi Camera Instructions
- June 15, 2024
- tp-link
Table of Contents
tp-link C310 V1 Outdoor Security Wi-Fi Camera
tp-link-C310-V1-Outdoor-Security-Wi-Fi-Camera-product
Product Information
Specifications
- Supported Connection: Ethernet
- Required Materials and Devices:
- A computer that supports Ethernet connection
- Two Ethernet cables (at least one)
- Problematic Tapo camera
- Camera firmware (.bin file)
Product Usage Instructions
Step 1: Download the Camera Firmware
Download the camera firmware according to your camera’s model number:
- Tapo C310 V1
- Tapo C310 V2
- TC65 V1
- Tapo C320WS V1
Once downloaded, unzip the file to reveal the .bin file.
Step 2: Connect the Problem Tapo Camera to the Computer
Connection Topology 1: Tapo Camera —- Router —- PC
- Connect the Tapo camera to the router using an Ethernet cable.
- Connect the computer to the router using another Ethernet cable.
- Change the IP settings of the computer network card:
- IP address: in the 0 (Zero) network segment, e.g., 192.168.0.123
- Subnet mask: 255.255.255.0
Connection Topology 2: Tapo Camera — Ethernet — PC
- Connect the Tapo camera to the computer using an Ethernet cable.
- Change the IP settings of the computer network card:
- IP address: in the 0 (Zero) network segment, e.g., 192.168.0.123
- Subnet mask: 255.255.255.0
Step 3: Upgrading via Web Interface
Note : The web interface may vary depending on the camera model, hardware, or firmware versions.
- Launch a browser on the computer and visit http://192.168.0.10
- Click “Browse” to locate the path of the firmware file you downloaded.
- Click “Upgrade”. Do not interrupt the power supply during the upgrade process.
Once the upgrade is complete, you will see a “Upgrade Success” message.
FAQ
Q: What materials and devices are required for using web emergency mode?
A: The materials and devices required are:
- A computer that supports Ethernet connection
- Two Ethernet cables (at least one)
- Problematic Tapo camera
- Camera firmware (.bin file)
Q: How do I change the IP settings of the computer network card?
A: To change the IP settings of the computer network card:
- For Connection Topology 1, set the IP address to be in the 0 (Zero) network segment, e.g., 192.168.0.123, and the subnet mask to 255.255.255.0.
- For Connection Topology 2, set the IP address to be in the 0 (Zero) network segment, e.g., 192.168.0.123, and the subnet mask to 255.255.255.0.
Q: How do I upgrade the camera firmware via the web interface?
A: To upgrade the camera firmware via the web interface:
- Launch a browser on the computer and visit http://192.168.0.10.
- Click “Browse” to locate the path of the firmware file you downloaded.
- Click “Upgrade”. Do not interrupt the power supply during the upgrade process.
Once the upgrade is complete, you will see a “Upgrade Success” message.
Instructions for using web emergency mode
Materials and devices below are required before the operation.
- A computer that supported Ethernet connection
- Two Ethernet cables (At least one)
- Problematic Tapo camera
- Camera firmware (The .bin file)
The operation steps are as follows:
Download the camera firmware according to your camera’s model number.
- Tapo C310 V1
- Tapo C310 V2
- TC65 V1
- Tapo C320WS V1
After downloading the firmware, unzip it, and you will see the .bin file.
Connect the problem Tapo camera to the computer:
Two types of connection are available (Choose the one that is convenient for
you):
Connection topology 1:
- Tapo camera—-< Router—-<Ethernet or PC
- After the connection is completed, change the IP settings of the computer network card (Figure 1 1).
Set a fixed IP address for the PC:
- IP address: in the 0 (Zero) network segment, e.g. 192.168.0.123
- Subnet mask: 255.255.255.0
Connection topology 2:
Tapo camera PC
- After the connection is completed, change the IP settings of the computer network card (Figure 1-1).
- Set a fixed IP address for the PC:
- IP address: in the 0 (Zero) network segment, e.g. 192.168.0.123
- Subnet mask: 255.255.255.0
Upgrading via web interface:
Note : the web interface may vary from different models, hardware, or
firmware versions.
- Launch a browser on the computer, visit http://192.168.0.10
- Click Browse to find the path of the firmware to be upgraded, and then click Upgrade. Do not interrupt the power supply during the upgrade process.
- Done, Upgrade Success (Figure 3-2-2)
