FRIDGGI B08MX19M74 Door and Window 3 In 1 Alarm Reminder Chime User Manual

FRIDGGI B08MX19M74 Door and Window 3 In 1 Alarm Reminder Chime

Door & Window 3in1
Alarm Reminder Chime

Please read this user manual before using and installation.

Introduction

• Satisure reinvent the Door and window Alarm, this new device offer 3in1 solution with three delays (Os to 20s) to satisfy all your needs: Entry Chime, Window/Door Alarm, Closing Reminder.
• Our main purpose was to protect kids when a Door or Window is left open; with Satisure regular reminders, you will never face this problem again.

Specifications

Operating Instruction

1. Power on operation:
   Peel off the insulating film, push the ON/OFF button to ON, the LED indicator lights up red, and the power is on.

2. Setting and adjustment

3. Short press the Up key: in order to cycle through the selection of music (the bell is divided into door bell (100OB, 90OB, 80OB) three sound levels), the alarm sound (120OB, 100OB, 90OB) three sound levels.

4. Short press the Down key: press (mode-1,mode-2 , mode-3) to select the operation in cyclic order, each short press time is less than 3 seconds.

5. Three modes setting:

6. Mode 1: Press the key shortly, cycle through the selections in order, and make a “BI” sound. Enter mode 1, the doorbell rings, and the LED light flashes for Os after opening the door. Reminds every 5s, and automatically stops or closes the door after 30 minutes. (Adapter personnel enter and exit reminder)

7. Mode 2 : Press the key shortly to cycle through the selections in order and make a “BIBI” sound. Enter mode 2, the doorbell will ring, the LED light will flash for 30s, and a reminder will be issued every 20s. Automatically stops after 60 minutes or when the door is closed. (Applicable to the outer door of the refrigerator, cold room)

8. Mode 3: Press the button shortly, cycle through the selections in order, and make a “BIBIBI” sound, enter mode 3, open the door for Os, the alarm will sound, the LED light will flash, and the doorbell will continue to ring. Manually close the alarm to stop. (Applicable to room entry reminder, anti-theft alarm)

9. Empty Batteries
   The AAA batteries can last up to 12 months and should be replaced when the alarm emits a continuous Beep sound.

10. Replace Batteries
    

11. Open the battery cover.

12. Take out old batteries.

13. Replace new batteries, please pay attention to the negative and positive.

Warm Attention before Installation

1. Please take out the battery insulating film before use.
2. The magnet and main unit should be less than 0.4 inch apart when closed.
3. Do not install the alarm near magnetic parts that might trigger the alarm by accident.
4. It is not waterproof, only can be used for indoor.
5. Please stick the alarm onto even and clean surface and note that sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or water will also affect the adhesion over a long period of time.

Installation

This alarm can be installed on doors, windows, and any other objects that can open and close. Before installation, please test whether the alarm can work properly to confirm that the door and frame are spaced correctly to accommodate the sensor.

1. Use a clean, dry towel to clean the area where you want to mount the alarm.
2. Tear off the adhesive tape from the main unit and magnet.
3. Stick the alarm to the place where you want, press hard for about 1 Os to fix them well.

Note: The magnet must be placed on the side of the main unit with a triangular sign.
The gap between the magnet and main unit should be less than 0.4 inch.

Troubleshooting

How to Contact After-sale Service?

If you have any product using questions, please do not hesitate to contact us through your order, our 2-hour email standby!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>