KitchenAid KDFE104K 24 Inch Dishwasher User Guide

KitchenAid KDFE104K 24 Inch Dishwasher

Product Information

Specifications

• Product: 24 Dishwasher
• Model Numbers: KDFE104K, KDTE104K, KDFE204K, KDTE204K, KDTE304LPA, KDFM404K, KDTM404K, KDPM604K, KDTM604K, KDPM704K, KDTM704K, KDTM704LPA, KDPM804K , KDTM804K, KDFE1 05P, KDTM405P
• Width of Door: 23 1/2″ (59.7 cm)
• Height to Top of Handle: 30 13/16″ (78.3 cm)
• Height of Adjustable Toe Kick: 3 5/16″ (8.4 cm)
• Width of Recessed Dishwasher: 22 5/8″ (57.4 cm)
• Depth without Door: 3 5/16″ (8.4 cm) – minimum, 4 11/16″ (11.8 cm) – maximum
• Depth with Towel Bar Handle: 26 7/8″ (68.3 cm)
• Depth with Pocket Handle: 24 1/2″ (62.6 cm)
• Depth of Panel-Ready Models: 24″ (61.0 cm)
• Height to Bottom of Door (minimum): 24″ (61.0 cm)
• Height to Top of Door (minimum): 3 5/16″ (8.4 cm)
• Height of Recessed Dishwasher (minimum): 33 7/16″ (84.9 cm)
• Depth with Door Fully Open (minimum): 33 5/8″ (85.4 cm)
• Depth with Toe Kick (minimum): 20 13/16″ (52.9 cm)

Product Usage Instructions

Facility
Before installing the dishwasher, please ensure that all surfaces have no protrusions that would prohibit installation.

To install the dishwasher:

1. Measure the opening/clearance dimensions as follows:
   • Minimum width: 24″ (62.0 cm)
   • Minimum height: 4″ (10.2 cm)
   • Minimum depth: 3″ (7.6 cm)
2. Check the shaded areas of the cabinet walls to determine where utility connections may be installed.
3. Ensure a minimum clearance of 2″ (5.1 cm) between the side of the dishwasher door and the wall or cabinet for corner locations.

Additional Information

• The dishwasher can be raised by 1 7/16″ (3.7 cm) with the feet fully extended.
• For panel-ready models, the dishwasher depth is 24″ (61.0 cm), not including the 3/4″ (1.9 cm) custom door panel.
• The insulation blanket thickness is not included in the dimensions and can be crushed up to 1/8″ (0.3 cm) or removed along the top perforated section for additional clearance.

FAQs

• Q: Can the dishwasher be raised?
  A: Yes, the dishwasher can be raised by 1 7/16″ (3.7 cm) with the feet fully extended.

• Q: What is the depth of the dishwasher with the door fully open?
  A: The depth of the dishwasher with the door fully open is a minimum of 33 5/8″ (85.4 cm).

• Q: Are the dimensions provided for planning purposes only?
  A: Yes, the dimensions provided are for planning purposes only. For complete details, refer to the Installation Instructions packed with the product.

• Q: Can the insulation blanket be removed for additional clearance?
  A: Yes, the insulation blanket can be crushed up to 1/8″ (0.3 cm) or removed along the top perforated section for additional clearance.

MODELS

This applies to all model numbers starting with;

• KDFE104K, KDTE104K, KDFE204K, KDTE204K, KDTE304LPA,
• KDFM404K, KDTM404K, KDPM604K, KDTM604K, KDPM704K,
• KDTM704K, KDTM704LPA, KDPM804K, KDTM804K, KDFE105P, KDTM405P

PRODUCT DIMENSIONS

The dishwasher can be raised 17/16″ (3.7 cm) with feet fully extended.

• Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice.
• Dimensions are for planning purposes only. For complete details, see the Installation Instructions packed with the product. Specifications are subject to change without notice.

(11.8 cm) – maximum
D| Width of the recessed dishwasher| 225/8″ (57.4 cm)
E †| Depth without door| 225/8″ ( 57.5 cm)
__

F † **

| Depth with Towel Bar Handle| 267/8″ (68.3 cm)
Depth with Pocket Handle| 241/2″ (62.6 cm)
Depth of Panel-Ready Models| 24″ (61.0 cm)
G| Height to bottom of the door (minimum)| 35/16″ (8.4 cm)
H| Height to top of door (minimum)| 337/16″ (84.9 cm)
I † ***| Height of recessed dishwasher (minimum)| 335/8″ (85.4 cm)
J †| Depth with door fully open (minimum)| 503/16″ (127.4 cm)
K †**| Depth with toe kick (minimum)| 2013/16″ (52.9 cm)

Insulation blanket thickness not included can be crushed up to 1/8″ (0.3 cm), or removed along the top perforated section for additional clearance.

• The dishwasher can be raised 17/16″ (3.7 cm) with feet fully extended.
• For panel-ready models, dishwasher depth is 24″ (61.0 cm), not including the 3/4″ (1.9 cm) custom door panel.

OPENING/CLEARANCE DIMENSIONS

IMPORTANT:
Check that all surfaces have no protrusions that would prohibit dishwasher installation.

• A. Measured from the lowest point on the underside of the countertop. May be reduced to 335/8″ minimum (85.4 cm) minimum by removing the feet and perforated area of insulation (blanket) on the dishwasher.
• B. Minimum, measured from the narrowest point of opening.

NOTE:
Corner locations require a 2″ (5.1 cm) minimum clearance between the side of the dishwasher door and the wall or cabinet.

DRAIN REQUIREMENTS

• A new drain hose is supplied with your dishwasher. If the drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and fits the 1″ (2.5 cm) drain connector of the dishwasher.
  NOTE: Do not connect multiple drain hoses.

• Make sure to connect the drain hose to the waste tee or disposer inlet above the drain trap in house plumbing and 20″ (50.8 cm) minimum above the floor. It is recommended that the drain hose either be looped up and securely fastened to the underside of the counter or be connected to an air gap.

• Make sure to use an air gap if the drain hose is connected to house plumbing lower than 20″ (50.8 cm) above the subfloor or floor.

• If required, the air gap should be installed per the air gap installation instructions. When you are connecting the air gap, a rubber hose (not provided) will be needed to connect to the waste tee or disposer inlet.

• Use 1/2″ (1.3 cm) minimum I.D. drain line fittings.

WATER SUPPLY REQUIREMENTS

• This dishwasher has a water heating feature and also requires a connection to a hot water supply line.

• A hot water line with 20 psi to 120 psi (138 kPa to 862 kPa) water pressure can be verified by a licensed plumber.

• 120°F (49°C) water at dishwasher.

• 3/8″ (0.95 cm) O.D. copper tubing with compression fitting or flexible braided water supply line.
  NOTE: 1/2″ (1.3 cm) minimum plastic tubing is not recommended.

• A 90° elbow with 3/4″ (0.95 cm) hose connection with rubber washer.

• Do not solder within 6″ (15.2 cm) of the water inlet valve.

• If installed in new construction, make sure the house water supply lines have been flushed prior to connecting the dishwasher to remove any debris that may exist in the supply line.

NOTE:
If replacing an existing dishwasher, it is recommended to install a new water line and drain hose (supplied) with the new dishwasher.

ELECTRICAL REQUIREMENTS

WARNING

Electrical Shock Hazard

• Plug into a grounded 3 prong outlet.
• Do not remove ground prong.
• Do not use an adapter.
• Do not use an extension cord.
• Failure to follow these instructions can result in death, fire, or electrical shock.
• Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/NFPA 70 – latest edition, and all local codes and ordinances.
• A copy of the above code standards can be obtained from:
• National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471

You Must Have:

• 120 V, 60 Hz, AC only, 15 A or 20 A, fused electrical supply
• Copper wire only
• A maximum of 2 field wiring supply conductors (12 AWG largest size) plus 1 grounding conductor are permitted in the terminal box.

We Recommend:

• A time-delay fuse or circuit breaker.

Circuit Requirements:

• The dishwasher may be installed on the same circuit as a garbage disposal providing that the branch circuit cannot exceed the rated circuit load and must comply with all governing codes and regulations such as but not limited to the National Electrical Code, ANSI/NFPA 70 – latest edition.
• No electrical connections other than the dishwasher power and ground connections can be made inside the dishwasher terminal box.

If connecting the dishwasher with a power supply cord:

• Use the listed power cord kit marked for use with the dishwasher.
• Plug into a grounded 3-prong outlet. The outlet must meet all local codes and ordinances.

If connecting the dishwasher with direct wiring:

• Use flexible, armored, or nonmetallic sheathed copper wire with grounding wire that meets the wiring requirements for your home and local codes and ordinances.
• Use a UL-listed/CSA-approved metallic strain relief.

®/™ ©2023 KitchenAid. All rights reserved. Used under license in Canada.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>