Hiberr YU-E20H Vocal Wireless Microphone User Guide

Hiberr YU-E20H Vocal Wireless Microphone

Specifications

• Frequency range: 520~570MHz
• Total number of channels: 200CH
• Frequency interval: 250KHz
• Effective use distance: 90m
• Frequency width: 50MHz
• Frequency module: 100 groups
• Oscillation mode: PLL phase-locked frequency synthesis

Product Overview

The YU-E20 Professional Wireless Microphone System is a UHF analog signal transmission system that provides excellent audio dynamic input range and supports up to 200 channels. It features 256 AES encrypted signal processing for safe and reliable performance. The system also offers automatic frequency scanning for establishing the most reliable connection with minimal effort. With a tuning bandwidth of 50 MHz, this microphone system ensures minimal delay and strong compatibility.

Product Usage Instructions

Recording Function (6.35mm Interface)

1. Connect the receiver to the recording device using a 6.35mm mono to 3.5mm dual channel audio cable.
2. Set the volume of the microphone host to 25VOL.
3. Adjust the volume and gain level of the system according to the actual situation when using a computer or mobile phone for recording.
4. To achieve clearer recordings, turn off the built-in sound effect of the system when using a computer or mobile phone for recording.

Receiving Host System Function Introduction

Front Panel

• Power key: Press this key to activate the information display on the LCD screen.
• LCD display screen: Shows the frequency, battery usage, and other information.
• Function button: Used for frequency scanning or synchronization.
• Up key: Adjusts the parameters of specific menu items.
• Down key: Adjusts the parameters of specific menu items.
• Function switch button: Controls volume and locking.
• Infrared sensing point/IR: Used for synchronous operation with the emitted frequency.

Back Panel

• Antenna input interface: Insert the two random equipped antennas into this interface respectively.
• 6.3mm mixed output interface: Audio output interface that mixes A and B channels.
• XLR balanced output interface: Used to connect balanced audio equipment.
• DC socket: Power socket for connecting the supplied power adapter.

Receiver System Usage Settings

To lock the receiving host:

1. Press and hold the VOL/LOCK button for about 3 seconds.
2. The receiving host will enter the locked state, indicated by a lock symbol on the screen.
3. Note: After locking, the system cannot adjust frequency and volume.

Frequently Asked Questions (FAQ)

Q: Where can I purchase the products and accessories?

• A: All our products and accessories can be purchased online from our online store.

Q: Do you provide B2B or OEM/ODM services for microphones?

• A: Yes, our company provides B2B or OEM/ODM services for microphones. Please contact us if necessary.

Q: How can I contact customer service?

• A: You can reach our customer service via email at service@hiberr.com.

Q: Where can I find more information about the company?

• A: For more information about our company, please visit our website or check out our Facebook Page.
• Please read the instruction manual carefully before operating the equipment, and keep the instruction manual properly.

WIRELESS MICROPHONE SYSTEM OVERVIEW

SYSTEM FEATURES

1. Excellent audio dynamic input range, easily retain every detail.
2. 256 AES encrypted signal processing, safe and reliable.
3. 50 MHz tuning bandwidth supports up to 200 channels.
4. Automatic frequency scanning to establish the most reliable connection with the least time and effort.
5. UHF analogy signal transmission, with minimal delay and strong compatibility.

TECHNICAL INDICATORS

Frequency range: 520~570MHz Total number of channels: 200CH Frequency interval: 250KHz Effective use distance: 90m Frequency width: 50MHz Frequency module: 100 groups Oscillation mode: PLL phase-locked frequency synthesis| Signal to noise ratio: >90dB Frequency stability: ±5KHz Receive mode: CPU

Frequency selection + pilot reception Display mode:LCD

Power supply: 12VDC, 500mA

Audio output interface: 2XLR+TRS6.3mm

| Frequency range: 520~570MHz Total number of channels: 200CH Frequency interval: 250KHz Frequency width: 50MHz Oscillation mode:

PLL phase-locked frequency synthesis

Frequency stability: ±4KHz

Pickup type: dynamic

NOTICE

• Please read this manual carefully and keep it.
• Please pay attention to all items in the manual.
• It is best to use original accessories such as adapters and cables.
• Please unplug the receiver from the device during thunderstorms or when the device will not be used for a long time.
• Do not place the receiver and transmitter near heat sources, such as radiators, ovens, etc., and keep them away from water.
• Do not spill liquids on the device, as this may damage the electronic components of the device.
• Please disconnect the power before cleaning.
• Use a soft cloth to clean the device.
• Cleaning with solvents or detergents is prohibited.

RECORDING FUNCTION (6.35MM INTERFACE)

1. Use 6.35 mono to 3.5 mm dual channel audio cable.
2. Suggestions for recording setting parameters
3. The volume of the microphone host is 25VOL.
4. For computers and mobile phones, please set the volume and gain level of the system according to the actual situation.
5. When using a computer or mobile phone to record, turn off the built-in sound effect of the system, and the recording will be clearer.

FCC STATEMENT FOR WIRELESS MICROPHONE SYSTEMS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a specific installation.
If this equipment does cause harmful interference to radio or television reception. (can be determined by turning the device off and on)

Users are advised to try one or more of the following measures to eliminate the distraction:

1. Adjust the direction or position of the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Notice:

Any changes or modifications to this equipment not expressly approved by the manufacturer could void your authority to operate the equipment. This device complies with Part 15 of the FCC Rules. The operation is subject to the following two conditions:

1. this device may not cause harmful interference;
2. This device must accept any interference received, including interference that may cause undesired operation Radio Frequency Exposure Information:

This equipment has been evaluated and found to comply with general RF exposure requirements. This device may be used in portable exposure conditions without any restrictions.

RECEIVING HOST SYSTEM FUNCTION INTRODUCTION

FRONT PANEL

1. Power key: After pressing this key, the information display will light up, and then it can be used and operated.
2. LCD display screen: information display screen, displaying frequency, battery usage and other information.
3. Function button: frequency scan or synchronization.
4. Up key: Used to adjust the parameters of specific menu items.
5. Down key: Used to adjust the parameters of specific menu items.
6. Function switch button: Volume / Lock.
7. Infrared sensing point/IR: used to operate synchronously with the emitted frequency.
   • BACK PANEL
8. Antenna input interface: Insert the two random equipped antennas into this interface respectively.
9. 6.3mm mixed output interface: audio output interface that mixes A and B channels.
10. XLR balanced output interface: used to connect balanced audio equipment.
11. DC socket: power socket, connect the supplied power adapter.

RECEIVER SYSTEM USAGE SETTINGS

1. LOCKING: PRESS AND HOLD THE ➏ VOL/LOCK BUTTON (ABOUT 3 SECONDS)
   • The receiving host will enter the locked state (the screen of the receiving host will display a lock symbol).
   • Note: After locked, the system cannot adjust frequency and volume.
2. Unlock: When the receiving host is locked
   • Press and hold the ➌ VOL/LOCK button (about 3 seconds) to unlock (the screen lock symbol of the receiving unit disappears).
3. Manually set the frequency:
4. Press the ➍➎ up or down key to select the target frequency;
5. Press the ➏ SCAN / SYNC button to confirm the selected frequency;
6. Press the ➏ SCAN / SYNC key again to enter the frequency synchronization interface (the receiving host will display IR————);
7. Align the infrared windows of the transmitting host and receiving host (about 3~7 cm). When the frequency displayed by the transmitter and the receiver are the same, the synchronization is successful.
8. Automatic scanning frequency
9. Press and hold the ➏ SCAN / SYNC key (about 3 seconds) to enter the automatic frequency selection mode (the frequency number on the screen of the receiving host is changing), the system will scan all channels; (Note: If you want to stop the program during the scanning process, please Press the SCAN/SYNC key).
10. After the scan is completed, the receiving host screen will display the best communication frequency, press ➏ SCAN / SYNC to enter the synchronization frequency interface (the receiving host will display IR————);
11. 3. Align the infrared windows of the transmitting host and receiving host (about 3cm). When the frequencies displayed by the transmitter and receiver are the same, the synchronization is successful.
12. Volume adjustment
13. Press the ➌ VOL/LOCK key to switch to the volume adjustment interface;
14. Press the ➍ UP or ➎ DOWN key to adjust the volume;
15. Press the ➏ SCAN / SYNC key to confirm the volume setting.

TRANSMITTER SYSTEM FUNCTION INTRODUCTION

TRANSMITTER (HANDHELD)

1. Pickup: It is used to pick up the original sound of human voice or musical instrument.
2. LCD display: display handheld status information (battery, frequency/channel, mute, etc.).
3. Power switch: Long press the switch to turn on or off the handheld transmitter.
4. Battery compartment: Unscrew the lower part of the tube body to see, used for installing and replacing batteries.
5. Infrared sensing point/IR: used for frequency binding operation with the receiver.
6. Antenna: RF antenna.

TRANSMITTER (BODYPACK)

1. Receiving antenna
2. Microphone input jack
3. Power switch / Volume knob
4. Power LED
5. LED display screen
6. Infrared receiving window
7. Battery compartment
8. Battery protection cover

CONTACT INFORMATION

• Company website：https://www.hiberr.com
• Online store：https://store.hiberr.com
• Customer service email：service@hiberr.com
• Facebook Page：https://www.facebook.com/hiberr.mic

1. All our products and accessories can be purchased online.
2. Our company provides B2B or OEM/ODM services for microphones, please contact us if necessary.

References

• Hiberr - Microphones, Wireless microphones, Conference microphones
• Hiberr - Professional in microphone customization

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>