OBENSKY JK-31-2 Walking Pad-Under Desk HOME USE TREADMILL INSTRUCTION Manual

OBENSKY JK-31-2 Walking Pad-Under Desk HOME USE TREADMILL

Thank you very much for purchasing our product.
Please read this instruction carefully before using it and keep the instruction at the proper place.

CAUTION

To avoid any hurt, please read this manual carefully before using it .

• For safety purposes, do not stand on the running belt while starting.
• Please stop immediately for any feeling of vomit or jerky during use.
• Please adjust the speed slowly.
• Do not adjust the belt during use.
• It is suggested to wear sports shoes when using the machine.
• Children, elders, pregnant women, and patients are prohibited from using the machine.
• Please clip the safety key on your clothing during use.
• This product is suitable for home use, not suitable for professional training and testing, and cannot be used for medical purposes.

SAFETY NOTICE

1. Please put the machine on flat ground. It is unsuitable to put the machine at the following places:

   • Outdoors.(The machine is specially designed for indoor use only)
     Slant ground or slant places on the balcony.

   • Sunlight area or near the heater

   • Noisy places.

2. The error may appear if the power is not stable. Please do not use the same socket together with the computer or air conditioner etc.

3. It is suggested to wear sports shoes and a gym suit when using the machine.

4. Please increase or decrease speed slowly.

5. Be careful of children or other objects while folding and unfolding the machine.

6. Do not put the machine near the wet object. The error may be caused by a water drop.

7. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from the manufacturer, its maintenance department, or similar departments.

8. When not using the treadmill, keep the safety key out of the reach of children.

9. Keep the oil bottle out of the reach of children. If you accidentally swallow it or get it into your eyes, rinse it with water and seek medical help in time.

10. There should be 1m (1000mm) on both sides and front of the treadmill, and 2 mx1 m (2000 mm*1000 mm) space at the back to emergency jump away. (Emergency jumpoff: While holding the armrests with both hands to prop up your body, step on the sidebars with your feet and jump off the treadmill from one side.)

CAUTION DURING USE

• If you do not feel well before using, please consult with your doctor or coach.
• It is not our company’s responsibility for any improper use by users to cause body injuries.
• Please pull up the plug after using it.
• Please pull out plug for any movement or change parts for the machine.
• Children, elders, pregnant women are prohibited from using the machine. Patients consult before using.
• Please place the machine in flat places. Do not locate any objects 2M behind the machine.
• The water drop is prohibited from running into the machine, especially to the motor, and power line, and plug.
• Danger may be caused if wearing long dresses or other unsuitable dresses during use.
• Encloser spaces, air-uncirculated places, and flammability places are prohibited from using the machine.
• Do not put any objects on the machine.
• Put away the plug from a heated place or fire seat
• Please switch off all functions and pull out the plug after use.
• Please do not stand directly on the belt while starting the machine.
• Do not disassemble the machine without the conduct of a professional person.
• Please make sure the running belt is fastened before using it.
• Do not jump up or down on the machine during exercise.
• May cause injuryduetofall.
• The machine must be grounded. In the event of a malfunction, grounding will provide a path of least resistance for current to reduce the risk of electric shock.

Technical Specification

Installation Notes

1. First step: Take the machine out of the box, and unscrew the adjustment knobs on both sides of the frame counterclockwise. Disengage the tooth groove of the handrail from the tooth groove of the treadmill (it is recommended to unscrew 3 turns).
2. The second step: Rotat the handrail until it hits thelimit and cannot rotate.
3. Third step: After aligning the tooth groove of the handrail with the tooth groove of the treadmill, turn the knob in time until it is tight. Insert the IPAD bracket, put on the safety key, and complete.

Control Panel

Display

1. The “TIME” window has two modes that show the running time.OForward counting time is from 0:00 to 99:59 minutes. @Countdown is count to O from the set time(setting range: minutes). The machine will stop slowly when it counts to 0:00 and shows” end”, then the machine will come to standby mode after 5 seconds.
   The “STEP “window shows the steps. It counts from O to 9999 steps. It will recount when the step numbers reach the top point.
   Note : The window will be switched from TIME and STEP cyclically, you can press the” M” button to switch between cyclic display mode and single display mode in motion state.

2. The “DISTANCE” window has two modes that show the current movement distance. Oln the forward counting mode, the distance will be increased from 0.0 to 99.9 miles, it will recount if the distance reaches the top point. @ln the distance countdown mode, the distance will be decreased from the setting data(setting range:l .00—99.OOmiles) to O . The machine will stop slowly when it counts to 0:00 and show” end”, then the machine will come to the standby mode after 5 seconds.
   The “CALORIES” window has two modes that show the calories.OForward mode counts from O to 9999, it will recount when it reaches the top point. @countdown mode will count from setting calorie data( setting ranges 20—990) to O. The machine will stop slowly when it counts to 0:00 and shows” end”, then the machine will come to the standby mode after 5 seconds.
   Note : The window will be switched from DISTANCE and CALORIES cyclically, you can press the” M” button to switch between cyclic display mode and single display mode in motion state.

3. The “SPEED” window shows the current running speed, the setting range is 0.5MPH-7.5MPH. The speed will +1- O. IMPH every time you click the “+1-” button. P1 P 12 are displayed under the setting of automatic selection.

4. After the treadmill starts, every window will be displayed cyclically at an interval of 5 seconds. You can press the “M” button to switch between cyclic display mode and single display mode.

5. The maximum speed of the treadmill will be limited to 4MPH when the dashboard deflected from a horizontal direction to an arbitrary direction by more than 45 degrees.

Function Of The Remote Control

1. Start/Stop”:
   • In standby or countdown mode: Press the “start/stop” button to start or stop the machine. Please note that the default speed is 0.5mph.
   • Choose the preset program: Press “start/stop” to start the machine and the speed will change according to the preset speed and accumulate the value.
   • In running state: Pressing “start/stop” , then the treadmill will stop slowly and back to the standby state.
2. Press the + – button is to adjust the speed. Keep pressing + T- over 0.5 seconds, the speed will keep increasing or decreasing. Please note the speed will change by 0.1 mph.
3. M 1 standby mode: it can switch from different modes, including Time, Distance, and Calories. @ln running mode: press the “M” button will switch display mode between cyclic display mode and single display mode.
4. “P”: There are POI—P12, a total 12 preset programs you can choose when in standby mode.
5. Press the once to mute the machine, and press it again to resume the beep sound.
6. After use, press the ” button, The treadmill will stop slowly and it will retain its data until power off. lt will resume the previous speed when starts again.
7. “Reset”: Press the ” ” button, and the data will reset. It only works when the treadmill is in standby mode.

About the Remote Control

1. Pull out the insulating sheet, you can use the remote control directly.
2. The remote control can directly control the treadmill.
3. If you have purchased multiple treadmills, in order to prevent the treadmills from interfering with each other, please perform the following operations to match.
   • Turn on the treadmill.
   • Simultaneously press the left and right buttons on the remote control for 5 seconds.
   • The display will flash, and the treadmill and the remote control will be paired.
   • Please note: After matching the remote control, if the remote control is replaced, please perform the matching again according to the above operation.

Functional instruction

1. Sports Mode: Press the start key to start the machine SPEED window will count from”3 21 “, default speed iSO.5mph, press + – to adjust speed.

2. Countdown Mode: when on standby, press the “M” key to choose Time, Distance, Calories countdown
   Press + – to set relevant data. After setting, press”start/stop” to start the treadmill,it will count down from the set data, and when counts to O, the machine will stop by itself.

3. Pre-set Program one program, then press + – to set the running time (time set cope time is30:OO), and press “start/stop” to start the machine, it will run according to the pre-set speed, and speed change according to the time ” (Time/20) “.

USAGE OF SILICONE OIL

Raise the running belt slightly. Then put the silicone oil to the running board. Then start the machine to run for 3 minutes without loading. It is better to maintain like this every 30 hours working of the machine. This can save lifetime of parts properly.

Runbelt Adjustment

1. The running belt deviates to the left
   Start the machine by the speed at 1.2-1.5mph/h without loading, use die nut to make the screw go 1/4 circle(see figl). Then make the machine running without loading 1-2 minutes. Please
   adjust like this to make the belt till to place.

2. The running belt deviates to the right
   Start the machine by the speed at 1.2-1.5mph/h without loading, use die nut to make the screw go 1/4 circle(see fig2). Then make the machine running without loading 1-2 minutes. Please adjust like this to make the belt till to mid place.

3. Running belt logjam
   If the running belt is in dead condition, use die nut to make the screw 1/2 circle both left and right till this logjam solved.

DAILY MAINTAINANCE

Please disconnect the power before checking the machine or cleaning. Clear belt and dial plate after use, at least once a week. Check and tighten screws and spines at fixing point. Do not hang clothes or other objects on the machine.

Trouble Shooting

Error

Code

| Meaning| Problem| Solution
---|---|---|---

Err(or E00)

| ****

No Safety key on Panel

| ****

Safety key is not on the panel or it is not properly put on

| 1.  Put safety key in the yellow area of panel.

2.  Err(or E00) still shows or there is no

function, change the computer screen/display monitor.

E2

| ****

Control Board Error

| Control board is broken or pseudo soldering on control board| ****

Replace control board

E4| Control Board Error| Control board is broken| Replace control board

E5

| ****

Over

current Protection

| ****

Control board short circuit or motor blocked

| 1.  Open the motor cover and check whether the motor is blocked. Remove the block if yes.

2.  Replace the control board if it’s not

blocked, or the error still shows.

E6

| ****

Motor Error

| ****

Motor broken or motor line fall off

| 1.  Open the motor cover and check whether the motor is broken or whether the motor wire is connected to control board properly. Reconnect the wire is recommended.

2.  Replace the control board if the error

still shows.

E7| Communication Failures| Wires from the control board to panel board are broken or not properly connected| 1.  Make sure the wires from the control board and panel board are connected securely and not damaged.

2.  Replace the control board if the error

still shows.

E8| Overload Protection| Excess of electricity or user exceeded max load weight| 1.  Make sure the user does not exceed max weight capacity.

2.  Reconnect power and re-start the machine.

3.  Replace the control board if the error

code still shows.

FAQs

How much noise does the OBENSKY JK-31-2 generate when in use?

It's designed to operate quietly, making it suitable for home environments without causing significant noise disruption.

What is the maximum weight capacity of the OBENSKY JK-31-2?

The weight capacity varies, so it’s important to check the manufacturer's specifications for this information.

How portable is the OBENSKY JK-31-2?

The JK-31-2 is designed for easy storage, often featuring a slim profile and portability options like wheels.

Can the OBENSKY JK-31-2 track fitness metrics?

It often comes equipped with a display or a companion app to track basic fitness metrics such as distance, time, and calories burned.

Is there an incline feature on the OBENSKY JK-31-2?

The JK-31-2, like most under-desk treadmills, generally does not include an incline feature, as it's designed for flat walking surfaces.

Does the OBENSKY JK-31-2 have a speed range suitable for walking and jogging?

Yes, it usually offers a range of speeds appropriate for walking and light jogging, but it's not intended for high-speed running.

What are the dimensions of the OBENSKY JK-31-2 Walking Pad?

The dimensions of the JK-31-2 are typically compact and slim, making it suitable for small spaces and under most desks. Exact dimensions should be confirmed from the product specifications.

What is the OBENSKY JK-31-2 Walking Pad?

The OBENSKY JK-31-2 is a compact, under-desk walking treadmill specifically designed for home use, allowing users to walk while working or engaging in leisure activities at home.

Where can I buy the OBENSKY JK-31-2 Walking Pad?

It's available through various online retailers, home fitness equipment stores, and possibly directly from OBENSKY's official website.

How do I maintain and clean the OBENSKY JK-31-2?

Regular cleaning, checking for loose parts, and storing it in a dry place are usually recommended. Detailed maintenance instructions are provided in the user manual.

Does the OBENSKY JK-31-2 come with a warranty?

Most likely, it comes with a manufacturer's warranty. The specifics of the warranty can be found in the product documentation.

Is there any assembly required for the OBENSKY JK-31-2?

It typically comes mostly assembled, requiring minimal setup efforts.

Video-OBENSKY Walking Pad-Under Desk Treadmill

Download This Manual PDF:OBENSKY JK-31-2 Walking Pad-Under Desk HOME USE TREADMILL INSTRUCTION Manual

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>