OAKCASTLE CD-150 Bluetooth CD Player User Manual
- June 15, 2024
- Oakcastle
Table of Contents
- OAKCASTLE CD-150 Bluetooth CD Player
- Product Information
- Product Usage Instructions
- Accessories
- Buttons Instruction
- Remote Control
- Operation
- Bluetooth Mode Instructions
- Troubleshooting
- SPEC & WARRANTY
- SAFETY INFORMATION
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
OAKCASTLE CD-150 Bluetooth CD Player
Product Information
Specifications
- Model: Oakcastle CD150
- Accessories: Remote control, Pack of screws, User Manual, Wall-mounted plate, USB to Type-C charging cable, Desk stand.
- Power Source: DC IN 5V
- Charging Time: Approximately 4 hours for a full charge
- Sound Effects: BBS, POP, JAZZ, ROCK, CLASSIC, FLAT
Product Usage Instructions
How to Turn the Player on/off
- A. The power switch is located on the side. Please toggle it to the ON position to play normally.
- B. The power switch is located on the side. Please toggle it to the OFF position to turn it off.
How to Charge the Player
Connect the supplied USB charging cable with the power adapter, then plug
it into a power source to charge the player. Alternatively, you can connect
the supplied USB Charging cable to a computer/desktop/car charger/power bank
to charge it.
- Charging Time: It will take about 4 hours for a full charge.
- Charging Indicator: When charging, the indicator on the player will be RED. Once the player is fully charged, the indicator will turn GREEN.
Note: When the player is in low battery, the LCD screen will be flashing. Please charge it.
How to Setup Circle Mode
Each time the REPEAT button on the remote control is pressed, the order of the
tracks played will be as follows:
- Repeat 1 (REP1): Repeat the current track
- Repeat all (ALL): Repeat all tracks
- Random play (SHUF): Play tracks in random order
How to Program the Play
- CD 01:25 REP1
Press the PROG button to enter the programming mode when the play stops. Press the PREVIOUS or NEXT button to select the track you want to program. Press PROG again to confirm the programming. You can program up to 20 tracks in this mode. After programming, press the PLAY button to enter the programming play mode. Press the STOP button directly to enter the stop mode to cancel or reprogram.
How to Setup EQ Effect
Press the EQ button to change the different sound effects. There are a total
of 5 sound effects: BBS, POP, JAZZ, ROCK, and CLASSIC, FLAT.
A-B Repeat
- A. During playback, press A-B to set the Starting Point A.
- B. Press A a second time to set the Ending Point B and the player will repeatedly play the part between Point A and Point B.
- C. Press A-B a third time to cancel A-B repeat and resume normal playback.
FAQ (Frequently Asked Questions)
-
Q: How long does it take to fully charge the player?
A: It will take approximately 4 hours for a full charge. -
Q: What are the available sound effects?
A: The available sound effects are BBS, POP, JAZZ, ROCK, and CLASSIC, FLAT. -
Q: How many tracks can be programmed in the programming mode?
A: Up to 20 tracks can be programmed in the programming mode. -
Q: How do I cancel or reprogram the programming play mode?
A: Press the STOP button directly to enter the stop mode and cancel or reprogram. -
Q: How do I set the A-B repeat?
A: During playback, press A-B to set the Starting Point A. Press A-B a second time to set the Ending Point B and the player will repeatedly play the part between Point A and Point B. Press A-B a third time to cancel A-B repeat and resume normal playback. -
Q: How do I switch to Bluetooth mode?
A: Press the MODE button to switch to Bluetooth mode. The LED display will show “BT” and the unit will be ready to pair with other Bluetooth devices such as mobile phones, pads, etc.
Accessories
Buttons Instruction
- Status display
- Remote control light sensor
- Light charging LED
- VOL-
- Mode
- Previous
- VOL+
- Next
- Pause/Play
- Stop
- DC IN 5V
- Power ON/OFF switch (Push the cable)
- AUX IN
- USB IN
- Earphone
- CD cover Open button
Remote Control
Operation
Button Operation
-
STANDBY
When the power on, turn the unit on/off. -
Number Pad (10+)
Press this button to enter the 10+ songs such as 10,20,30,etc. -
PLAY/PAUSE
- Press PAUSE button to pause playback.
- Press it again to continue playing from where it was paused.
-
STOP
- Press STOP button to stop playback.
- Press PLAY Button to play from the beginning.
-
MUTE
Press to mutes the audio output on the player. -
VOL+/VOL Press to increase or decrease the volume output.
-
MODE
Press to change the playing mode. -
PROGRAM
PROGRAM button apply for CD, USB, AUX, Bluetooth, FM Radio, MP3, WMA & HD-CD. This function allows you randomly assign 20 songs (max) and play them in order. -
AUX IN
Connect it with the AUX output device(such as DVD player, CD player or Mobile phone, etc) via AUX cable.
Basic Operation
-
How to Turn the Player on/off.
- A. the power switch is located on the side. Please toggle it to the ON position to play normally.
- B. the power switch is located on the side. Please toggle it to the OFF position to turn it off.
-
How to Charge for the Player
Connect the supplied USB charging cable with the power adapter, then plug it into a power source to charge the player. OR Connect the supplied USB Charging cable to a computer/ desktop/car charger/power bank to charge it. Charging Time: It will take about 4 hours for a full charge. When charging, the charging indicator on the player will be RED. Once the player is fully charged, the indicator will turn to GREEN.
NOTE: When the player is in low battery, the LCD screen will be flashing. Please charge it. -
How to setup the Circle Mode
Each time the REPEAT button on the remote control is pressed, the order of the tracks played will be as follows: Repeat 1(REP1), Repeat all (ALL), random play(SHUF). -
How to Program the Play
Press the PROG button to enter the programming mode when the play stops, press the PREVIOUS or NEXT button to select the track you want to program, press PROG again to confirm the programming. Up to 20 tracks can be programmed in this mode. After that, press the PLAY button to enter the programming play mode. Press the STOP button directly to enter the stop mode to cancel or reprogram. -
How to setup EQ effect
Press the EQ button to changes the different sound effects. There are a total of 5 sound effects: BBS, POP, JAZZ, ROCK, and CLASSIC,FLAT. -
A-B Repeat
- A. During playback press “A-B” to set the Staritng Point A.
- B. Press “A-B” a second time to set the Ending Point B and player will repeatedly play the part between Point A and Point B.
- C. Press “A-B”a third time to cancel “A-B” repeat and resume normal playback.
Bluetooth Mode Instructions
- Press the “MODE” button to switch to Bluetooth mode, the “BT” will show on the LED display, then the unit will be ready to pair with other Bluetooth devices such as mobile phones, pads, etc.
- Activate the Bluetooth in your mobile phone and it will automatically search for nearby Bluetooth devices to pair.
- Choose the name ” HCD-12 ” device in your mobile phone Bluetooth device list to pair.
- Your mobile phone will be paired/connected to the CD player in a few seconds.
- Playing music on your mobile phone and the audio will be transmitted to the CD player speaker through Bluetooth.
Note: This Player isn’t compatible with Bluetooth headsets, Bluetooth speakers, and the Car’s Bluetooth.
USB Mode Instructions
- Plug in a USB stick to the CD player USB port.
- Press the “MODE” button to switch to USB mode.
- The CD player will read and play the music in the USB stick automatically.
Note:
- Supports a maximum 32GB USB flash drive, which must be FAT-32 format.
- If can’t read the USB stick, please check the format and capacity. If not FAT-32 format, please format it to FAT32.
FM Mode Instructions
- Press the “MODE” button to switch to FM radio mode.
- Press the ” ” button to go to auto searching, the channels will be automatically stored when searching channels.
- After auto searching finished, press button to adjust channels. (Note: the channels storage capacity is 40 channels. P1-P40)
Troubleshooting
Problem | Reason | Solu on |
---|---|---|
Cannot be turned on | Switch is not turned on. | Press the ON/OFF bu on. |
HOLD is turned on. | Press the HOLD bu on. | |
The baery is exhausted. | Charge the ba ry. | |
The player is damaged. | Please contact Oakcastle Tech Support. | |
Cannot read discs | The disc is installed incorrectly. | 1. Make sure |
the label side of the disc is facing up.
2. Ensure disc is inserted fully.
The disc cannot be recognised.| The player is only compa ble with CD, CDR, MP3
& HDCD
The disc is dirty or damaged.| 1. Make sure the disc is not heavily
scratched or damaged.
2. Wipe the disc gently from the centre towards to the edge of the disc with a clean and so cloth.
3. Try another disc to check if the disc is faulty.
The loader is dirty.| Wipe the lens gently with a degreasing co on swab.
Cannot charge ba ery| There is no current at poweroutlet.| Make sure the
power outlet is working.
The plug is not plugged incorrectly.| Make sure that the two plugs of the
power cords are connected correctly.
The charger is damaged.| Replace a charger with one that matches the original
specifica on (DC5V/1A).
The player is damaged.| Please contact Oakcastle Tech Support. NOTE: While
charging, make sure the Power Source and the Charging Voltage are DC5V/1A.
Excessive voltage inputmay cause machine overload damage.
Automa cally skips parts of the contents of the disc| The player has
MODE func on (Repeat, Repeat All, Random
Play& Preview Play).
| Please ensure Preview Play MODE is off.
Noisy & Screaming when it plays| Usage me of the disc may be too long, so
the disc is not smooth.| 1. Make sure the disc is not heavily damaged.
2. Wipe the disc gently from the centre towards to the edge of the disc with a clean and so cloth.
3. Try another disc to check if the disc is faulty.
If there is a scratching sound from inside of the CD player this might be caused due to the CD not being inserted correctly.| Please change to another disc, and do not use the other one again.
SPEC & WARRANTY
Installation Instructions
- Fix the wall-mounted plate on the wall with 4 screws (included in the package).
- Hang the CD player on the wall-mounted plate.
Product Features
Model | CD150 |
---|---|
Frequency response | 20-22KHz |
Power output of earphones | 16mW+16mW/16-32Ohm |
Impedance of earphone | 32Ohm/16mW |
Compatible Disc | CD/CDR/HDCD/MP3/WMA |
Bluetooth | Bluetooth Speaker, Version: 4.2 |
HIFi Speaker | Support EQ function 3Wx2 |
USB | Support MAX 32G/ FAT 32 Format |
Battery | Rechargeable battery 3.7V 2000mAh , Support about 3 hours |
Power source | Micro USB 2.0 Standard |
Power consumption | about 10W |
Dimensions (LWH): | 165x165x45mm |
Weight | 502.4g |
WARRANTY
All products come with a standard 12-month warranty. All items must be
registered on www.oakcastle.co.uk for the warranty to be valid. Once on the
web page, use the menu to find “register your product”. You will also be given
the chance to extend your warranty for an additional 24 months, free of
charge.
SAFETY INFORMATION
- Read these instructions.
- Keep these instructions. Instructions are also available for download at www.oakcastle.co.uk
- Heed all Warnings
- Follow all instructions
- Do not clean the apparatus near or with water
- Do not block any ventilation openings. Install by the manufacturer’s instructions
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Protect the power from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in a way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to the rain or moisture, does not operate normally or has been dropped.
- No naked flame sources, such as lit candles, should be placed on the apparatus.
- Dispose of used electrical products and batteries safely according to your local authority and regulations.
ADDITIONAL WARNINGS
The apparatus shall not be exposed to dripping or splashing and no objects
filled with liquid, such as vases, shall be placed on the apparatus. The main
plug is used to disconnect device and it should remain readily operable during
intended use. In order to disconnect the apparatus from the main mains
completely, the mains plug should be disconnected from the main socket outlet
completely. The battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
RECYCLING ELECTRICAL PRODUCTS
You should now recycle your waste electrical goods and in doing so help the
environment. This symbol means an electrical product should not be disposed of
with normal household waste. Please ensure it is taken to a suitable facility
for disposal when finished with.
IMPORTANT: Please read all instructions carefully before use and keep for future reference.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>