Sunco DL_SL6_NL-WH-2750K 6 Inch Slim Selectable Nightlight User Manual

Sunco DL_SL6_NL-WH-2750K 6 Inch Slim Selectable Nightlight

Product Information

Specifications

• Voltage: 120V
• Wattage: 6W
• Wattage Equivalency: N/A
• Beam Angle: N/A
• Weight: N/A
• Housing Material: N/A
• Dimmable: Yes
• Model: DL_SL6_NL-WH-2750K
• Average Lifetime: 50,000 hrs
• Lumens: 1100LM
• Moisture Rating: Damp
• CRI: 90+
• Usage: Indoor
• IC Rated: Yes
• Warranty: 7 Years

Product Usage Instructions

Before You Start
Safety Information:
To reduce the risk of fire, electric shock, or physical injury:

• This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference.
  2. This device must accept any interference that may cause undesired operation.
• Please review all instructions carefully before installation.

Quickstart Guide

1. Step 1: Use template to cut hole.
2. Step 2: Connect supply & junction wires.
3. Step 3: Attach fixture to junction box.
4. Step 4: Insert fixture into ceiling.

Installation Guide

STEP 1:

1. Turn off circuit breaker before installation.
2. Cut out 6.33 housing size on Installation Template, then tape onto ceiling in desired location.
3. Cut ceiling hole using Installation Template as a guide.

STEP 2:

1. Open junction box and remove appropriate knockout.

STEP 3:

1. Connect supply and junction wires using wire nuts:
   • Black to Black (Live)
   • White to White (Neutral)
2. Tuck connected wires inside junction box & close cover.

STEP 4:

1. Slide the CCT Selection Switch to choose from five color temperatures: 5000K, 4000K, 3500K, 3000K, 2700K.
2. New Construction Applications:
   • Secure to studs, joists, or similar fixed structural units.
3. Remodel Applications:
   • Do not require to secure to studs, joists, or similar fixed structural units.

STEP 5:

1. Attach fixture to junction box using connector as shown on image (1). Tighten connector by hand (2).
2. Push up spring clips and insert fixture into ceiling.
3. Turn on circuit breaker and test light.

STEP 6:
Note: To toggle between downlight and nightlight, turn wall switch and night light off, wait 3 seconds, then switch on. To reset fixture, turn off, wait 5 seconds, then turn on.

FAQ
Common Troubleshooting

• Issue: Light isn’t turning on.
  Solution: Double-check if fixture is properly connected and circuit breaker hasn’t been tripped.

• Issue: Light isn’t bright enough. Dimming not working.
  Solution: Ensure that the dimmer switch being used is compatible with the product. Refer to the recommended dimmers list provided in the user manual for compatible dimmers.

Whats in the Box

Nightlight Selectable

Get Your Gear

Before You Start

Safety Information
To reduce the risk of fire, electric shock, or physical injury:

• Turn off the circuit breaker before installing this fixture.
• This product should be installed by a person familiar with the construction and operation of the product and the hazards involved. Safety eyeglasses and gloves are recommended.
• Abide by related regional and local laws or regulations.
• Proper grounding is required to ensure safety.
• Do not alter, relocate, or remove wiring during installation.
• Do not make or alter any open holes in the wiring enclosure or electrical components during installation.
• Check for shipping damage before installing. If the product is damaged, do not use it.
• Keep fixtures away from corrosive substances.
• Suitable for damp locations at temperatures ranging from 4°F to 113°F. Not for use where directly exposed to water.
• Clean the fixture regularly to ensure proper operation. Do not clean with harsh solvents.
• Use safety precautions and abide by regional and local laws or regulations.
• This product is not compatible with 3rd party sensors.
• This product is not compatible with photo controls.
• This product is not compatible with occupancy sensors.
• This product is not compatible with timing devices.

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation. Please review all instructions carefully before installation.

Quickstart Guide

Installation Guide

• STEP 1

  • a. Turn off circuit breaker before installation.
  • b. Cut out 6.33” housing size on Installation Template, then tape onto the ceiling in the desired location.
  • c. Cut ceiling hole using the Installation Template as a guide.

• STEP 2

  • a. Open junction box and remove the appropriate knockout.

• STEP 3

  • a. Connect supply and junction wires using wire nuts:
  • Black to Black (Live)
  • White to White (Neutral)
  • b. Tuck connected wires inside junction box & close cover.

• STEP 4
  Slide the CCT Selection Switch to choose from five color temperatures. Insert junction box through the ceiling hole.

  • a. New Construction Applications: Secure to studs, joists, or similar fixed structural units.
  • b. Remodel Applications: Do not require to secure to studs, joists, or similar fixed structural units.

• STEP 5

  • a. Attach fixture to junction box using the connector as shown on image (1). Tighten the connector by hand (2).
  • b. Push up spring clips and insert fixture into ceiling. Turn on circuit breaker and test light.

• STEP 6

  • Note: To toggle between the downlight and the nightlight, turn wall switch and night light off, wait 3 seconds, then switch on.
    To reset fixture, turn off, wait 5 seconds, then turn on.

Product Details

Recommended Dimmers

Specifications

Common Troubleshooting

Feeling in the dark about an issue with your product? No worries! Our troubleshooting section is here to shed some light and provide you with easy- to-follow solutions for any problem.
If you still need some assistance, please feel free to contact us with any questions. Our team of lighting experts are happy to help brighten your day .

Light Distribution Angle

• Lighting distribution angle refers to the spread of light emitted from a light source. It is an important factor to consider when selecting a fixture or bulb, as it affects the way it will illuminate an area. There are two main types of lighting distribution angles:
• Asymmetric lighting distribution emits light evenly in all directions, creating a cone-shaped pattern that provides a pool of light. This type of lighting is ideal for general lighting and illuminating large areas. Common applications for symmetric lighting include general area illumination, security lighting, and perimeter lighting. Symmetric lighting is also used to a certain degree in up-lighting.
• An asymmetric lighting distribution angle, also known as a beam angle, creates a pattern that focuses light in a specific direction. This type of lighting is ideal for task lighting as it reduces glare and light spills in other areas. Common applications include task lighting in spaces such as landscape settings, retail stores, museums, and much more.
• It is important to note that the lighting distribution angle can also be affected by other factors such as the reflector design of the light source, the type of lens used, and the distance between the light source and the surface being illuminated.

Customer Support

• Warranty Policy
  This product is covered by our industry-leading 7-year warranty. It gets even better – scan the QR code for 2 extra years of protection!

• 30-Day Return Policy
  At Sunco we value our customers and stand by the quality and performance of our products. If you are not completely satisfied with your purchase, we accept returns within 30 days of your purchase date.

• Customer Service
  Our Los Angeles team of lighting experts is here to assist you with all your needs! Contact us at:
  Email: support@sunco.com
  Text or Call: 844-334-9938 6 AM – 6 PM PST Monday – Friday

support@sunco.com
844-334-9938

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>