Enventor Y011R Green Laser Level Instructions

: June 15, 2024
: Enventor

Table of Contents

Operation & LED Indicator
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Inventor **Y011R Green Laser Level Instructions

**

NOTE

Thank you for purchasing Inventor Y011G/Y011R Laser Level. Before using the product, please read this manual thoroughly to ensure proper use.

Safety Instructions

WARNING

Please read thoroughly and comply with the Safety Instructions and User Manual before using this product.ailure to read and follow may void the warranty

WARNING

CLASS II LASER PRODUCT
COMPLIES WITH CFR 1040.10 AND 1040.11
Max. Power Output: <1mW
Wavelength: 505nm-660nm
LASER RADIATION:
DO NOT STARE INTO BEAM.
DO NOT DIRECT EYE EXPOSURE.
AVOID VIEW WITH OPTICAL INSTRUMENTS.

ATTENTION

Read all instructions prior to operating this laser tool. Do not remove any labels from too

While the product is in operation, be careful not to expose your eyes to the emitting laser beam . Exposure to a laser beam for an extended time may be hazardous to your eyes.
Do not attempt to view the laser beam through optical tools such as telescopes as serious eye injury may result.
Do not disassemble or modify the laser in any way. Modifying the tool may result in hazardous Laser Radiation Exposure.
Do not operate the laser around children or allow children to operate the laser. Serious eye injury may result.
An exposure to the beam of a Class 2 laser is considered safe for a maximum of 2 seconds. Eyelid reflexes will normally provide adequate protection.
The following label/print samples are placed on the product to inform of the laser class for your convenience and safety

User Guide, Maintenance and Care：

When not in use please power OFF the tool and place the pendulum lock in its locked position.
The laser tool is sealed and calibrated at the plant to the accuracy specified.
It’s recommended to carry out an accuracy check before its first use and periodic checks during future use, especially for precise layouts.
Do not store the laser tool in direct sunlight or expose it to high temperatures.
Exterior plastic parts may be cleaned with a damp cloth, NEVER use solvents. Use a soft, dry cloth to remove moisture from the tool before storage.
Do not dispose of this product with household waste.
Please recycle in line with local provisions for the collection and disposal of electrical and electronic waste under the WEEE Directive.

CAU ON

LASER RADIATION-DO NOT STARE INTO THE BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS MAX OUTPUT <1mW 2505nm-660nm CLASS I LASER PRODUCT COMPLIES WITH CFR 1040.10 AND 1040.11

Charging and Battery Safety

Please read thoroughly and comply with the battery safety instructions and precautions before charging.
Failure to read and follow may result in personal injury, fire, and property damages if the battery is charged and/or used improperly.

Charging Precautions:

Suitable power adapter: Universal adapter with output of 5V=1A or 5V=2A
The first charging time is recommended to be more than 4 hours. Each charge time is not less than 2.5 hours, but not more than 12 hours.
If the laser tool is not used for an extended time, please charge once every 6 months, each charging time is not less than 4 hours.
The best charging temperature: 0℃ to 20℃ (32℉ to 68℉)

Battery Safety:

DO NOT SHORT CIRCUIT. Short circuits may cause fire, and injury!
Do not charge unattended.
Do not disassemble, or modify the battery.
Keep away from children, and pets.
Immediately discontinue use of the battery if the battery abnormal/ deformed (emits an unusual smell, feels hot, changes color or shape, or appears abnormal in any other way). Please contact themnufacturer to replace it.
Never charge or store the batteries inside your car. Extreme temperatures (low or high) might ignite the battery, and cause a fire.
Do not place the battery in high-pressure containers, microwave ovens, or on induction cookware.
Do not carry, or store the batteries together with hairpins, necklaces, or other metal

objects.

On (battery electrolytes) exposure to skin, flush with water immediately. If eye exposure occurs, flush with water for 15 minutes, and seek emergency care immediately

Mode	Y011G-Green Beams	Y011R-Red Beam
Laser Class:	Class 2 (IEC/EN60825-1/2014), <1mW
Laser Wavelength	505-530nm	625-645nm
Leveling Accuracy	±3mm/10m(±1/9 in. at 33 ft)
Leveling / Compensation Range:	3°± 1° ≤4 second
Reference Working Distance ( 60-100 LUX):	25m / 82	20m / 65ft
Reference Working Distance (with Laser Detector)	Up to 50m / 164f	Up to 35m

NOTE

Appearance and specifications may differ due to product improvement.
Working distance varies depending on the operating environment.
When use with receiver for a larger working range, it’s necessary to turn on the pulse mode.

.Product Overview

Operation Button
LED Indicator
Laser Window
Pendulum / Transit Lock
1/4″-20 threaded mount
Type – C Charging Port

Operation & LED Indicator

Turn ON the laser tool:

Method 1 – Turn ON the self-leveling mode:

Slide the pendulum to the Unlocked Position to turn ON the laser tool, the self-leveling mode is activated by default.
The laser beams blink fast when the tool is out of self-leveling range (3° ± 1°).

Method 2 – Turn ON the manual / Tilt mode:

When the pendulum in Locked Position, press operation button(1) and hold for ≥ 2 seconds to turn ON the laser tool, the manual mode is activated by default.
The laser beam will blink about every 5 seconds to notify the user it is not self-leveling
now.
Under manual mode, users can position the laser tool at various angles. Note: Please notice the laser beam projected in manual mode cannot be used as a horizontal or vertical reference in nature.

Lines Switching:

After power on, all laser beams will be on by default. •Short press operation button(1) to switch horizontal and vertical laser line.

Turn OFF the laser tool:

Step 1: Slide the pendulum/transit switch to the Locked Position.
Step 2: press operation buttons(1) and hold for ≥ 2 seconds to turn the laser tool OFF.

NOTE

The laser level can only be turned off when the pendulum/transit in its Locked Position.

Pulse Mode (Use with Laser Receiver):

Under pulse mode, laser tool can work with a laser receiver for working in a brighter environment or a larger working distance.
It is necessary to turn on the pulse mode when use with the receiver. Switch to Pulse Mode:
Step 1: Turn ON the laser tool.
Step 2: short press the operation button twice in a row to switch to Pulse Mode.
The laser beams are dimmer in pulse mode, and the LED indicator(2) will light up in blue.

Return Back to Normal Mode:

short press the operation button twice in a row to return back to Normal Mode.
The laser beams will be recovered, and the LED indicator (2) will light up in green.

LED Indicator :

After Power ON, the LED indicator will light up in Green.
When the battery is low, the power indicator will flash in red.
During charging, the power indicator will flash in green.
When charging is complete, the power indicator will light up in green continuously.
When switching to pulse mode, the LED indicator will light up in blue.
When the battery voltage is low, switch to pulse mode, the LED indicator will flash in red.

After-Sales Service Hot-mail

For questions about this or any other Products, please email us: aftersale_service@en ventor.net.

EU DECLARATION OF CONFORMITY
We hereby declare that the essential requirements set out in the EMC
directive 2014/30/EU and ROHS directive 2011/65/EU and FCC and IEC60825.
have been fully fulfilled on our product with Indica tin as below:
Manufacturer: ZHONGSHAN SMART OPTOELECTRONICS TECHNOLOGY CO, LTD
Address: 1/F-3,Building A, No 16 Tianjin 3rd Road, Taizhou Town, Zhongzheng,
Guangdong, China
Object(s) of the declaration；
Product: :Self-leveling Cross Line Laser Level；
Model Number: Y011G,Y011R
Type: Electric
Applied Standard:
the EMC Directive 2014/30/EU
EN55032:2015
EN55035:2017
ROHS directive 2011/65/EU:
IEC62321-4:2013/AMD1:2017;IEC62321-5:2013;
IEC62321-6:2015;IEC62321-7-1:2015;
IEC62321-7-2:2017;IEC62321-8:2017
FCC
FCC Part 15 Subpart B
IEC
IEC 60825-1:2014